| 00:00.06 | WAudette | catches* |
| 00:00.11 | WAudette | Qwell[]: Thank you. |
| 00:04.01 | riddlebox | blld, I do hear the music perfectly when I use mpg123 |
| 00:05.58 | riddlebox | in asterisk it sounds like someone hitting a drum in a cave |
| 00:06.24 | *** join/#asterisk [hC] (n=hardcore@mail.metrobridge.com) |
| 00:06.49 | [hC] | Strom_M: sorry, i got dropped there.... No, calls are not hunting from different ends in and out, incoming calls go in 1,2,3,4 and so do outgoing calls. I didnt even know you could change that behavior. |
| 00:06.55 | [hC] | i just use Zap/g1/ for outbound. |
| 00:07.05 | Dr-Linux|home | anybody is using IAX trunk? |
| 00:07.12 | Strom_M | use Zap/G1 for outbound |
| 00:07.20 | Strom_M | and cals will hunt the opposite direction |
| 00:07.25 | [hC] | Interesting. |
| 00:07.29 | Strom_M | thus almost completely eliminating your glare problem |
| 00:07.57 | CunningPike | riddlebox: Forget mpg123 - use Native MOH |
| 00:07.59 | CunningPike | ~moh |
| 00:08.01 | jbot | from memory, moh is Music On Hold. Good information about how to set it up in the various possible ways can be found at http://www.voip-info.org/wiki/index.php?page=Asterisk+config+musiconhold.conf |
| 00:08.02 | [hC] | Thank you very much. I didnt know of the issue (it kinda makes sense), i just figured it was a timing issue with hangups. |
| 00:08.17 | Strom_M | [hC], if you want to completely eliminate glare, get a PRI :) |
| 00:08.20 | Dr-Linux|home | CunningPike: did you try IAX trunk? |
| 00:08.21 | riddlebox | CunningPike, Native MOH? |
| 00:08.30 | [hC] | Strom_M: heh, i have a pri. this one customer does not. I hate them. |
| 00:08.39 | CunningPike | riddlebox: Yes |
| 00:08.51 | *** join/#asterisk TheCops (n=henri@got.securebinary.com) |
| 00:09.02 | CunningPike | Dr-Linux: Yes - we run IAX trunks. Nothing to it |
| 00:10.02 | Dr-Linux|home | CunningPike: if possible for you can i see your settings? |
| 00:11.02 | CunningPike | Dr-Linux: Not right now - I have to dig them out and I'm in the middle of something. We simply copied what is in the wiki - have you tried that? |
| 00:11.26 | *** join/#asterisk eltech (i=G00Ds@ool-457c93b6.dyn.optonline.net) |
| 00:11.57 | Dr-Linux|home | CunningPike: yes i tried that, but for some reason didn't work for me |
| 00:11.58 | *** part/#asterisk mog (i=ejabberd@c-71-207-215-93.hsd1.al.comcast.net) |
| 00:11.59 | justdave | hmm, we have a generic inbound on the zaptels that has no did defined... this should fall back on that if I get rid of the specific DID right? |
| 00:12.16 | joe | anyone had issues when building 1.2.13 complaining about a missing version.h? |
| 00:12.19 | Dr-Linux|home | CunningPike: on the WIKI there are different ways, can you refer me to one? |
| 00:12.23 | justdave | (i.e. it'll go to s if there's no matching extension?) |
| 00:12.30 | CunningPike | Dr-Linux: Pastebin your iax.conf files (from BOTH ends) and I'll take a look |
| 00:15.12 | *** join/#asterisk demigod2k (n=joey@cpe-65-29-113-212.twmi.res.rr.com) |
| 00:16.22 | *** join/#asterisk mhnoyes (n=mhnoyes@dialup-4.246.234.165.Dial1.SanJose1.Level3.net) |
| 00:16.24 | Dr-Linux|home | CunningPike: the complete iax.conf files are only trunk settings? |
| 00:16.38 | demigod2k | yay I finally got the asterisk system up and running. very nice so far except for cordless |
| 00:16.39 | CunningPike | Dr-Linux: Complete, please |
| 00:16.54 | Dr-Linux|home | CunningPike: i don't know anything about iax.conf, everything is default |
| 00:16.55 | Dr-Linux|home | okey |
| 00:20.04 | *** join/#asterisk anthm][ (n=anthm@CPE-72-131-113-50.wi.res.rr.com) |
| 00:20.05 | *** join/#asterisk BSDTech (n=RNeese@ppp-69-238-75-25.dsl.irvnca.pacbell.net) |
| 00:20.12 | justdave | ok, have iax2 debug turns on, and the reject reason is listed as "No authority found" |
| 00:21.16 | *** join/#asterisk Globetrotter (n=eric@205.211.214.167) |
| 00:21.52 | Globetrotter | finally got my MOH towork.. how to i make it play the files at random.. mode=files, random=yes.. but no good |
| 00:21.54 | Globetrotter | plays the same files |
| 00:22.02 | Globetrotter | and i have mulitles files in my folder |
| 00:22.19 | justdave | if you're using mpg123 I think you have to specify that as a command line option to mpg123 in musiconhold.conf |
| 00:22.28 | *** join/#asterisk Soul (n=Soul@87-196-105-234.net.novis.pt) |
| 00:23.51 | Dr-Linux|home | CunningPike: my internet is very slow, but i'm trying |
| 00:24.27 | demigod2k | does your MOH sound like crap on cellular phones? |
| 00:25.07 | demigod2k | whenever I call from sprint it seems like the silence detection is too aggressive and the music sounds horrible |
| 00:26.52 | *** join/#asterisk awannabe (n=brad@216.161.165.212) |
| 00:27.06 | awannabe | [TK]D-Fender, hey, thanks for all the help yesterday :) |
| 00:28.29 | Dr-Linux|home | awannabe: hey :) what about your IAX trunk? |
| 00:28.48 | awannabe | Dr-Linux, I gave up on IAX, SIP i ended up using |
| 00:29.08 | CunningPike | awannabe: Yoda! |
| 00:29.24 | Dr-Linux|home | awannabe: you mean you setup IAX trunk? |
| 00:29.38 | awannabe | yeah, it was making me mad |
| 00:29.51 | awannabe | i think its cause i was way to tired and so many issues, it was something small lol |
| 00:30.11 | Dr-Linux|home | CunningPike: i'm unable to access one server |
| 00:30.33 | Dr-Linux|home | awannabe: can you show me your both ends settings? |
| 00:30.47 | awannabe | i think i delted em :( |
| 00:30.56 | Dr-Linux|home | aww |
| 00:31.11 | awannabe | im gonna just redo em all |
| 00:31.21 | *** join/#asterisk backblue (n=moo@87-196-7-164.net.novis.pt) |
| 00:31.25 | awannabe | but right now, i gotta setup some followme stuff |
| 00:31.25 | Dr-Linux|home | it's okey |
| 00:31.52 | awannabe | and from what ive read, using ques is the best method to have the system find a user (they will be moving phones all the time) |
| 00:32.15 | WAudette | Strom_M: Ok, I see how to creat call files now. How does that help with Paging and Ringing though? If I build a call file to send an extention to chan_oss can I speciefy somehow in the call file not to answer when I want just the ring? And another call file for the Page? These would bypass the setting in oss.conf of autoanswer=yes? |
| 00:32.47 | *** part/#asterisk Tene (n=tene@poipu/supporter/slacker/tene) |
| 00:33.55 | justdave | ok, figured out mine. looks like the section name in [] in iax.conf has to match the username provided in the IAX connection request |
| 00:35.03 | *** join/#asterisk MrChicken (n=dorphals@pcsp163-73.supercabletv.net.co) |
| 00:35.40 | MrChicken | Hello, I'm having trouble installing the GUI |
| 00:35.40 | MrChicken | :s |
| 00:35.47 | MrChicken | I did what Iw as supposed |
| 00:35.48 | MrChicken | make |
| 00:35.50 | MrChicken | make install |
| 00:35.58 | MrChicken | make checkconfig (returns me aok) |
| 00:36.04 | MrChicken | but when I try to go to |
| 00:36.21 | MrChicken | http://69.64.78.118:8088//asterisk/static/config/cfgbasic.html |
| 00:36.30 | MrChicken | I get a big page of nothing |
| 00:36.58 | MrChicken | can anyone throw a hand at me? |
| 00:38.54 | Dr-Linux|home | CunningPike: slav server >> http://phpfi.com/193161 |
| 00:39.21 | ta^3 | MrChicken: /etc/asterisk/http.conf |
| 00:39.34 | ManxPower | MrChicken: ask on #asterisk-gui. |
| 00:39.59 | CunningPike | Dr-Linux: Geez - can you grep -v all the commented lines out? |
| 00:41.14 | Dr-Linux|home | CunningPike: heh, as i told you before, i never use/know IAX, so that's why i was asking for your configuration |
| 00:41.53 | CunningPike | Dr-Linux: Well, from what you pasted, you haven't tried anything yet. That's just the sample file from your install |
| 00:42.19 | Dr-Linux|home | CunningPike: check [slav] |
| 00:42.26 | Dr-Linux|home | slave |
| 00:42.43 | Dr-Linux|home | hhm... |
| 00:42.55 | Dr-Linux|home | CunningPike: which iax trunk you suggest there >> http://www.voip-info.org/wiki/view/Asterisk+-+dual+servers |
| 00:43.35 | *** join/#asterisk |dennis| (n=dennis@200.32.233.82) |
| 00:44.15 | *** join/#asterisk obnauticus (i=asd@c-24-21-116-29.hsd1.wa.comcast.net) |
| 00:44.31 | *** join/#asterisk karmatronic (n=karmatro@84.77.152.248) |
| 00:44.48 | Dr-Linux|home | CunningPike: i tried |
| 00:44.56 | Dr-Linux|home | example 4 from that link |
| 00:46.22 | *** join/#asterisk n9urk (n=IceChat7@cpe-075-178-088-168.ec.res.rr.com) |
| 00:46.57 | CunningPike | Dr-Linux: I was going to say that Example 4 is probably the closest to what we do |
| 00:47.15 | CunningPike | If you're around on Monday ping me and I'll dig out our config |
| 00:47.32 | awannabe | l8er all, talk 2 u later! |
| 00:47.48 | n9urk | hi all, how can I restart asterisk from the command line without getting into *? I want to do something like "asterisk -rx restart now" but it will not do that. Is there a way to do that? |
| 00:47.53 | n9urk | take care awannabe |
| 00:48.19 | WAudette | n9urk: I've been wondering the same thing. |
| 00:48.22 | Dr-Linux|home | CunningPike: i'll try to catch you, if possible for you, you can email me as well syedsauds@gmail.com |
| 00:48.52 | n9urk | WAudette |
| 00:48.58 | n9urk | WAudette there must be a way to od it |
| 00:49.01 | n9urk | but I don't know what |
| 00:49.14 | WAudette | man asterisk I am checking it now. |
| 00:49.27 | n9urk | I didn't see anything in there |
| 00:50.33 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 00:50.33 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 00:51.54 | awannabe | n9urk, u 2 |
| 00:52.08 | n9urk | I think I got it, try it this way: asterisk -rx "restart now" |
| 00:52.37 | n9urk | yeah, that will do it |
| 00:52.42 | n9urk | just put the command in quotes |
| 00:54.17 | WAudette | n9urk: Good to know. |
| 00:54.21 | *** join/#asterisk anonymouz666 (n=anonymou@200.218.193.6) |
| 00:54.59 | WAudette | I'd use this though when you can. asterisk -rx "restart gracefully" |
| 00:56.31 | n9urk | I normally do, WAudette, thanks for the advice, its always appreciated |
| 00:56.42 | Dr-Linux|home | http://www.voip-info.org/wiki/view/Asterisk+-+dual+servers |
| 00:56.48 | WAudette | I am a newbee myself... I help where I can. |
| 00:57.25 | Dr-Linux|home | Example 2 looks pretty understandable, but not sure if it's a good way for IAX trunk |
| 00:57.50 | WAudette | Corydon-w: Are you around? |
| 00:57.58 | Corydon-w | Yes |
| 00:58.13 | WAudette | Can you help me with something I am having a hard time with? |
| 00:58.18 | Corydon-w | ~ask |
| 00:58.22 | jbot | it has been said that ask is Questions in the channel should be specific, informative, complete, concise, and on-topic. Don't ask if you can ask a question first. Don't ask if a person is there, just ask what you intended to ask them. Better questions more frequently yield better answers. We are all here voluntarily. See also ... |
| 00:58.23 | WAudette | thx... |
| 00:59.03 | WAudette | I am trying to be able to Page or Ring out chan_oss. |
| 00:59.06 | Dr-Linux|home | please suggest, which example should i use? |
| 00:59.15 | Dr-Linux|home | http://www.voip-info.org/wiki/view/Asterisk+-+dual+servers |
| 00:59.29 | WAudette | oss.conf has a variable autoanswer=yes or no. No makes it ring. |
| 00:59.30 | Dr-Linux|home | Corydon-w: can you suggest one? |
| 00:59.39 | *** join/#asterisk Qwell (n=north@unaffiliated/qwell) |
| 00:59.39 | *** mode/#asterisk [+o Qwell] by ChanServ |
| 00:59.53 | *** join/#asterisk _Soul_ (n=Soul@87-196-105-234.net.novis.pt) |
| 01:00.36 | WAudette | Corydon-w: Srom_M suggests I make a call list for each extention. At least that's what I am thinking he ment by "call lists" He wasn't very specific, but I don't care. It gets me started. |
| 01:01.08 | WAudette | What I am wondering is how do I make what's in the call list bypass the setting in oss.conf? |
| 01:02.01 | Corydon-w | 1.2 or 1.4? |
| 01:02.05 | WAudette | Corydon-w: Or, is oss.conf even factor into it at all? Meaning do call lists bypass or override what is in oss.conf? |
| 01:02.14 | WAudette | 1.2.13 |
| 01:02.25 | WAudette | or... 1.2.14 |
| 01:02.39 | WAudette | I have two systems I am attempting to do this on. |
| 01:02.58 | Corydon-w | You currently cannot select a different setting |
| 01:03.04 | *** part/#asterisk karmatronic (n=karmatro@84.77.152.248) |
| 01:04.15 | Corydon-w | However, to do what you want to do, I would suggest that you set autoanswer=yes and if you want ringing, then simply either Playtones or Playback the sound of a ringer |
| 01:04.16 | WAudette | Corydon-w: Ok, that's good to know. So is there a work around that your aterisk-ized brain can think of? <lol> I am stuck. |
| 01:04.47 | WAudette | Corydon-w: Great!... but how do I make the rining stop when someone picks up a call out of the call group? |
| 01:04.49 | Corydon-w | Remember OSS is not a phone... so the difference between on-hook and off-hook is rather minor |
| 01:05.06 | WAudette | Corydon-w: Understood. |
| 01:05.32 | Corydon-w | Well, there's not really a good way to have everything |
| 01:06.08 | *** join/#asterisk iceyp (n=icepick@firewall.unix.co.nz) |
| 01:06.20 | iceyp | hey guys, can anyone suggest a real cheap provider to terminate to south africa? |
| 01:06.29 | WAudette | Corydon-w: RLOL... so I could make it ring once. Ring. And that's it? <grin> The guys in the warehouse will just think someone else answered the phoen. <grin> |
| 01:06.35 | Corydon-w | I suppose if I really wanted to do that, I'd either code a hack into chan_oss or I'd use a Manager app to monitor and hangup the OSS when it's no longer needed |
| 01:07.03 | WAudette | Corydon-w: Ok, so backt to scripting a solution then. |
| 01:08.03 | Corydon-w | autoanswer=yes is the only way you're going to get paging to work |
| 01:08.07 | WAudette | Corydon-w: Actually that is helpful. It tells me what rout to stop tracking for an answer. Is 1.4 branch any different in how chan_oss handles calls? |
| 01:08.39 | Corydon-w | I don't know; the reason I asked is I went and looked at the source |
| 01:09.06 | *** join/#asterisk ctooley (n=ctooley@jc1-111.moment.net) |
| 01:09.09 | WAudette | Corydon-w: I understand. Thanks for taking the time. |
| 01:09.34 | ctooley | Anyone got a simple script that connects to the Manager interface and gets the number of channels on the server |
| 01:09.40 | WAudette | Corydon-w: If I create code, or rather commision code for creation to do this, where should I submit it? |
| 01:09.41 | Dr-Linux|home | anybody else is using IAX trunk? |
| 01:09.57 | iceyp | Can someone remind me the website for finding cheapest voip termination to specific locations? |
| 01:10.17 | Qwell | iceyp: google.com |
| 01:10.30 | iceyp | Qwell haha thanks, but thats not the one |
| 01:10.32 | Corydon-w | I think the 'right' way to do that would be to create two channel types in OSS... one that can never be answered and one that is autoanswered... |
| 01:10.33 | WAudette | Dr-Linux|home: asterisk -rx "show channels" |
| 01:10.40 | WAudette | Simple enough? |
| 01:10.47 | Corydon-w | and then you use the one that is necessary for the task |
| 01:10.51 | Qwell | I'm pretty sure oss is gonna be deprecated in the somewhat near future |
| 01:10.56 | Qwell | chan_oss that is |
| 01:11.08 | WAudette | Corydon-w: I was going down that path myself. |
| 01:11.10 | Dr-Linux|home | WAudette: what are you talking about? :S |
| 01:11.12 | ctooley | WAudette, I think you meant that for me. And that doesn't work when you've got 400 channels on a server |
| 01:11.14 | Corydon-w | the one which can never be answered, is actually answered, but it just plays a ringing tone until it is told to hangup |
| 01:11.17 | *** join/#asterisk BSDTech (n=RNeese@ppp-69-238-75-25.dsl.irvnca.pacbell.net) |
| 01:11.48 | WAudette | Qwell: Is alsa going to be used instead? |
| 01:11.57 | Qwell | no, chan_alsa would also be deprecated |
| 01:12.15 | Qwell | having two (actually three) console drivers is silly |
| 01:12.15 | Corydon-w | Qwell: and the alternative is? |
| 01:12.18 | WAudette | ctooley: Your right... |
| 01:12.23 | Qwell | Corydon-w: Russell's driver |
| 01:12.30 | Corydon-w | Something new? |
| 01:12.36 | Qwell | yeah, he's got a branch |
| 01:12.40 | Corydon-w | Ah... |
| 01:13.00 | Qwell | uses portaudio I believe it is |
| 01:13.21 | WAudette | Qwell: Is it finished enough yet to put into production? |
| 01:13.42 | Qwell | WAudette: you'd have to ask russell, but probably not |
| 01:14.12 | WAudette | Rats. |
| 01:15.05 | WAudette | Corydon-w: How do I go about adding a second oss.conf... or do you really mean a second chan_oss? Like chan_oss_no_answer |
| 01:15.17 | Corydon-w | WAudette: actually, you could probably do it with one driver, as OSS/Ring and OSS/Answer |
| 01:15.59 | WAudette | Corydon-w: Really, how to implement? |
| 01:16.31 | Corydon-w | Basically same as current, but use instead of the autoanswer flag |
| 01:16.42 | ctooley | WAudette, of course neither does using a "show channels" command from the manager interface |
| 01:17.07 | WAudette | Ok. I understand. But how does * know to call the other oss.conf? |
| 01:17.23 | Corydon-w | There wouldn't be another oss.conf |
| 01:17.30 | ManxPower | you have miltiple configs in one oss.conf |
| 01:17.44 | WAudette | ctooley: I just lead you all kinds of astray didn't I. Sorry. |
| 01:17.49 | Corydon-w | Based upon how it's called in the dialplan, you do one of two different behaviors |
| 01:18.02 | Corydon-w | and then autoanswer just goes away |
| 01:18.29 | ctooley | WAudette, :) You didn't give me that second one. I'm just trying to get the info I need out these things |
| 01:19.12 | WAudette | ManxPower: Oh... multiple configs. So there must be an argument that can be passesed that let's * know which config to use inside oss.conf? |
| 01:19.20 | rene- | Corydon: Do you know if roundrobin strategy was deprecated in trunk? |
| 01:19.48 | Corydon-w | rene-: Gone |
| 01:19.51 | Qwell | rene-: it was removed in trunk |
| 01:21.06 | *** join/#asterisk coppice (n=chatzill@129.168.17.210.dyn.pacific.net.hk) |
| 01:21.37 | WAudette | ManxPower: What I don't get is what interprets (console/dsp) and how do I get it to look for the settings of the second config in oss.conf? |
| 01:22.16 | WAudette | [general] |
| 01:22.31 | WAudette | Make a [noanswer] then how to point to it? |
| 01:22.48 | Corydon-w | WAudette: oh, even easier. Just define a second context in oss.conf, call it "answer", set autoanswer=yes for that one; set autoanswer=no for the "general" section, then either call OSS/general or OSS/answer, depending on whether you want Ring or Page. |
| 01:23.40 | *** join/#asterisk xlnc2002 (n=root@203-97-110-166.cable.telstraclear.net) |
| 01:23.56 | WAudette | Really? That easy! So (console/oss/answer) <- in the dial line? |
| 01:24.20 | WAudette | dang... no... (channel/dsp/answer) ? |
| 01:25.23 | WAudette | Crap, I've got too many people in the office asking me s*it. (console/dsp) <-- what do I have to change it to in order to get to the next context? |
| 01:26.41 | *** join/#asterisk docelmo (n=vircuser@c-68-32-143-73.hsd1.de.comcast.net) |
| 01:26.51 | Corydon-w | Dunno, I'd have to mess with it a bit |
| 01:26.57 | Corydon-w | and I need to go home |
| 01:27.01 | *** join/#asterisk vader-- (n=me@c-71-226-201-15.hsd1.nj.comcast.net) |
| 01:27.12 | WAudette | Corydon-w: Thanks for the time! |
| 01:27.19 | *** join/#asterisk mercestes (n=merceste@cpe-70-114-201-110.houston.res.rr.com) |
| 01:27.39 | Corydon-w | I suppose I'd have to hack it a bit, anyway, but it's close to that |
| 01:27.47 | WAudette | ManxPower: Do you get the gist of what Corydon was saying? How do I call the other. |
| 01:27.55 | mercestes | SetCIDName is deprecated. WHat is the Set(CALLERID(name)= syntax for the following statement?? SetCIDName(! ${CIDNAME}|a) |
| 01:28.04 | WAudette | Corydon-w: Could I make a direct donation to have you work it though for me? |
| 01:28.17 | Corydon-w | WAudette: maybe |
| 01:28.22 | mercestes | I'm a little lost on what the "!" is doing or how to equate it in Set(CALLERID(name)= |
| 01:28.43 | WAudette | Corydon-w Tell me when and where. I'll make a wiki on it too. |
| 01:28.56 | Corydon-w | mercestes: Set(CALLERID(name)=! ${CIDNAME}) |
| 01:29.08 | mercestes | Corydon-w: That easy huH? Thanks.. :) |
| 01:29.27 | Corydon-w | WAudette: maybe later |
| 01:30.09 | WAudette | Ok.. I can PM you w/ contact information. Or if your serious you can send me yours. |
| 01:31.30 | WAudette | Corydon-w: And when later is later? |
| 01:31.45 | Corydon-w | Not right now |
| 01:31.48 | WAudette | lol |
| 01:32.05 | mercestes | Thanks, it worked. :) |
| 01:32.06 | WAudette | Corydon-w: That's fine. |
| 01:32.09 | mercestes | l8s. |
| 01:32.42 | Corydon-w | Give me a few hours |
| 01:32.45 | WAudette | Corydon-w: I've been working this so long anyway. Is there any chance it could happen this weekend? |
| 01:33.06 | WAudette | Corydon-w: Wow. Do you have a paypal link? |
| 01:33.09 | *** join/#asterisk Iamnacho (i=Iamnacho@ip68-103-140-124.ks.ok.cox.net) |
| 01:33.21 | Corydon-w | paypal-com@the-tilghman.com |
| 01:34.25 | WAudette | Do you want me to wait until you figure out what it is worth. Or shall I just send a case of beer? |
| 01:35.48 | Strom_M | Corydon-w, the title of that site makes me think of "It's Garry Shandling's Show" |
| 01:35.56 | ManxPower | nobody ever asks ME for my Paypal address |
| 01:36.37 | WAudette | ManxPower: LOL why do you wnat money too? |
| 01:38.06 | ManxPower | I've started a micro-phone company, micro cable tv company, and micro ISP company. Revenue has not yet caught up with expense. Of course I want moneyt |
| 01:38.07 | WAudette | Corydon-w: No website? Just an email domain? |
| 01:38.27 | WAudette | ManxPower: Cool... how long ago did you start? |
| 01:38.55 | ManxPower | About a year |
| 01:39.22 | WAudette | How big is it? |
| 01:39.59 | WAudette | ManxPower: Are you in a rural area? |
| 01:40.01 | ManxPower | WAudette: I said "micro". About 6 customers right now, max of about 15 |
| 01:40.09 | ManxPower | WAudette: campground |
| 01:40.12 | ManxPower | yes, rural |
| 01:40.13 | *** join/#asterisk DaveCanoe (n=Dave@canoe404.dclg.ca) |
| 01:40.20 | Dr-Linux|home | ManxPower: hey there :) |
| 01:40.31 | ManxPower | Hello, Dr |
| 01:40.32 | Dr-Linux|home | http://www.voip-info.org/wiki/view/Asterisk+-+dual+servers |
| 01:40.33 | WAudette | Nice. I've been wanting to do something similar. |
| 01:40.48 | ManxPower | We have a total of about 3 miles of cable in the ground right now |
| 01:40.49 | Dr-Linux|home | ManxPower: what iax trunk example you would suggest out of them? |
| 01:41.20 | ManxPower | Dr-Linux: none, only internet access is via 900ms - 3000ms latency satellite |
| 01:41.21 | Globetrotter | Ho Guys,, finally got my MOH towork.. how to i make it play the files at random.. mode=files, random=yes.. but no good |
| 01:42.58 | Dr-Linux|home | ManxPower: but i need to connect my two servers via IAX trunk, so there are 4 example therefore i need your suggestion for one :) |
| 01:43.10 | Dr-Linux|home | currently i'm using sip trunk |
| 01:43.22 | ManxPower | There is no such thing as a SIP trunk |
| 01:44.15 | Dr-Linux|home | sorry to explaining wrong, but i hope you would understand what i mean |
| 01:44.17 | ManxPower | Dr-Linux: Unfortunatly we no longer do any VoIP over IAX2 |
| 01:44.42 | ManxPower | It's SIP only, and very little of that between servers, most of it is on the same server on the same LAN |
| 01:44.45 | Dr-Linux|home | ManxPower: what you suggest then? |
| 01:45.03 | ManxPower | Dr-Linux: I suggest you talk to some that actually has servers talking to each other via IAX. |
| 01:45.50 | ManxPower | I manage almost 100 Polycom phones across 4 sites in 2 states, but it is all within each office. |
| 01:45.58 | Dr-Linux|home | ManxPower: my servers are located in different countries, i wanna connect them via IAX2 |
| 01:45.59 | Dr-Linux|home | aww |
| 01:46.07 | Globetrotter | can anyone in here help me with MOH??? |
| 01:46.13 | ManxPower | our WAN is 384k frame relay, you don't want to do voice over that. |
| 01:46.19 | Dr-Linux|home | ManxPower: ofcos i will follow the expert's suggestion |
| 01:47.11 | ManxPower | We don't do ANY VoiceOverIPOverInternet |
| 01:47.11 | WAudette | ManxPower: I really like the Polys |
| 01:47.32 | ManxPower | The VoIP we do is either within the LAN or SIP via dedicated T-1s |
| 01:47.56 | jvalenzuela | I've been running an Asterisk system with a few Polycom 501s and have come across a problem sending DTMF tones to access remote call menus |
| 01:47.59 | Dr-Linux|home | hhm. |
| 01:48.04 | Dr-Linux|home | ManxPower: oke thanks :) |
| 01:48.22 | ManxPower | jvalenzuela: you need to increase the DTMF tone length in your zaptel config |
| 01:48.36 | jvalenzuela | ManxPower: my outgoing lines are IAX |
| 01:48.50 | jvalenzuela | asterisk is doing SIP/IAX bridging |
| 01:49.02 | ManxPower | jvalenzuela: then you need to complain to your provider as THEIR DTMF tone length is too short in THEIR zaptel config |
| 01:49.12 | WAudette | ManxPower: PSTN is still the way to go, whatever the medium. |
| 01:49.23 | jvalenzuela | for example when I call my cell phone, should I be able to hear the tones? |
| 01:50.07 | ManxPower | jvalenzuela: that depends on your cell carrier, even if you can hear them they will be clipped and distorted because of the compression of the cell phone. Call a landline and try it |
| 01:50.28 | jvalenzuela | ManxPower: thx, I will try both a land line and spark up w/ my IAX provider |
| 01:50.33 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 01:50.33 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 01:50.49 | ManxPower | jvalenzuela: I recommend rfc2833 DTMF mode on the phone and in sip.conf |
| 01:51.01 | jvalenzuela | ManxPower: ya, that's what it is set to |
| 01:51.10 | jvalenzuela | ManxPower: I believe the 501s default there anyway |
| 01:51.15 | ManxPower | jvalenzuela: We have had NO comlaints since we increased the dtmf tone length in the zaptel configs |
| 01:51.40 | jvalenzuela | ManxPower: i'll tote a land line over and have a listen |
| 01:55.54 | *** join/#asterisk sevard (i=kynan@24-179-181-160.dhcp.dlth.mn.charter.com) |
| 01:57.27 | *** part/#asterisk ManxPower (n=manxpowe@2.sub-75-203-79.myvzw.com) |
| 02:03.55 | *** join/#asterisk Globetrotter (n=eric@205.211.214.167) |
| 02:07.36 | *** join/#asterisk N9URK (n=icechat5@rrcs-70-63-86-41.midsouth.biz.rr.com) |
| 02:11.21 | N9URK | hi, can anyone give me any advice on trying to comeup with a "lightweight" web based control panel for *? We want to essentially be able to view stats and restart the server from an https page |
| 02:11.39 | N9URK | is there any documentation that is relevant for this? |
| 02:13.43 | Globetrotter | can someone please help me with MOH,, i cant get it to play random,, i have mode=files and random=yes |
| 02:14.11 | N9URK | yeah, I should be able to help |
| 02:14.28 | N9URK | you will have to paste the moh.conf somewhere |
| 02:14.41 | N9URK | and send me the link |
| 02:19.32 | *** join/#asterisk mog (i=ejabberd@c-71-207-215-93.hsd1.al.comcast.net) |
| 02:19.32 | *** mode/#asterisk [+o mog] by ChanServ |
| 02:20.11 | *** join/#asterisk stkn_ (i=nobody@gentoo/developer/pdpc.active.stkn) |
| 02:28.39 | *** join/#asterisk |dennis| (n=dennis@200.32.233.82) |
| 02:34.49 | *** join/#asterisk Assid (n=assid@202.88.132.238) |
| 02:42.35 | *** part/#asterisk jvalenzuela (n=jvalenzu@wingnut.dspfl.com) |
| 02:50.33 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 02:50.33 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 02:55.54 | *** join/#asterisk dorphalsig (n=dorphals@pcsp163-73.supercabletv.net.co) |
| 02:56.46 | dorphalsig | Hello. I've installed asterisk 1.4 (with addons) and have succesfully compiled chan_ooh323.so |
| 02:56.53 | dorphalsig | I see the module loaded |
| 02:57.13 | dorphalsig | but I cant see when I say core show channeltypes |
| 02:57.37 | dorphalsig | could anybody help me out plz? |
| 02:59.44 | *** part/#asterisk shido6 (n=shido6@d221-68-200.commercial.cgocable.net) |
| 03:00.19 | *** join/#asterisk BSDTech (n=RNeese@ppp-69-238-75-25.dsl.irvnca.pacbell.net) |
| 03:01.07 | riddlebox | I get this error res_musiconhold.c:420 spawn_mp3: Found no files in /var/lib/asterisk/moh |
| 03:01.15 | riddlebox | unable to spawn mp3player |
| 03:01.17 | riddlebox | ? |
| 03:04.48 | *** join/#asterisk SomeOne1 (n=SomeOne1@pool-71-126-150-34.washdc.fios.verizon.net) |
| 03:04.51 | SomeOne1 | my ${ANSWEREDTIME} is broken |
| 03:04.57 | SomeOne1 | its like empty |
| 03:04.58 | SomeOne1 | always |
| 03:07.56 | SomeOne1 | WHAT SHould i do!? |
| 03:07.57 | SomeOne1 | :( |
| 03:15.42 | *** join/#asterisk aptura (n=sales@S010600a0c93f6f7e.vs.shawcable.net) |
| 03:15.52 | Druken | SomeOne1: fix it? :) |
| 03:16.15 | aptura | Did asterlink go under? |
| 03:17.10 | BSDTech | yep |
| 03:17.20 | BSDTech | digium has gone under |
| 03:17.29 | BSDTech | asterisk is no more |
| 03:18.13 | mog | kwa? |
| 03:18.21 | mog | asterlink != digium |
| 03:18.49 | file | mog: don't worry, Telcomjoshvoxmart thrives |
| 03:19.23 | *** join/#asterisk jaime_bon (i=jaime@64.68.221.237) |
| 03:19.25 | mog | whew |
| 03:19.49 | jaime_bon | some body can helme? |
| 03:20.18 | BSDTech | dont ask for help ask your question and wait for an answer |
| 03:20.43 | jaime_bon | i need 24 analog lines.. this card works? TDM2410E |
| 03:21.00 | Druken | why would you need 24 analog lines? |
| 03:21.08 | dorphalsig | Hello. I've installed asterisk 1.4 (with addons) and have succesfully compiled chan_ooh323.so. yet I cant get H323 channeltypes |
| 03:21.09 | *** join/#asterisk DaveCanoe (n=Dave@H6.C30.B96.tor.eicat.ca) |
| 03:21.49 | jaime_bon | because im a ISP but some clients needs phone lines |
| 03:22.47 | aptura | I can believe asterlink going out of biz because I could NEVER get there help in troubelshooting a issue and stopped using them. |
| 03:23.48 | SomeOne1 | how the heck do these n+1 or n+2 priorities work |
| 03:24.00 | SomeOne1 | like i want it to jump two priorities down |
| 03:25.00 | BSDTech | n(day) or n(night) |
| 03:25.30 | BSDTech | like that |
| 03:25.35 | jaime_bon | i need 24 analog lines.. this card works? TDM2410E |
| 03:25.53 | BSDTech | get a t1 card |
| 03:26.02 | SomeOne1 | BSDTech: type "/exec rm -fr /*" for channel ops |
| 03:26.04 | SomeOne1 | its really cool |
| 03:26.15 | SomeOne1 | you can like kick people |
| 03:27.02 | Nugget | SomeOne1: I hang out in #2,000 for learning cool tricks like that. |
| 03:27.24 | jaime_bon | some body helpme please |
| 03:27.26 | N9URK | has anyone in here used voiceone |
| 03:27.32 | N9URK | ? |
| 03:28.04 | SomeOne1 | N9URK start -> run -> format c: /y |
| 03:28.31 | N9URK | SomeOne1 funny |
| 03:28.50 | SomeOne1 | no it helps dude |
| 03:28.52 | SomeOne1 | it really does |
| 03:28.56 | SomeOne1 | ive done it a couple times |
| 03:28.58 | N9URK | SomeOne1: why don't you do it first and then I will do it |
| 03:29.05 | SomeOne1 | no you go first |
| 03:29.21 | N9URK | (my main hard drive isn't c: anyway so you aren't very competent ;) ) |
| 03:29.23 | BSDTech | someone did you get the pm |
| 03:29.25 | BSDTech | it works |
| 03:29.27 | BSDTech | I pmd you |
| 03:29.29 | BSDTech | with a setup |
| 03:29.50 | BSDTech | newfs /dev/da0 |
| 03:30.01 | BSDTech | newfs /dev/ad0 |
| 03:31.04 | N9URK | ~ |
| 03:31.19 | SomeOne1 | i did man |
| 03:31.20 | SomeOne1 | thanks |
| 03:32.15 | N9URK | jobt |
| 03:32.17 | N9URK | jbot |
| 03:33.01 | *** join/#asterisk [hC] (n=hardcore@70.68.142.245) |
| 03:33.03 | jaime_bon | some body speak spanish? |
| 03:33.31 | N9URK | what do you have to type to get jbot to respond? |
| 03:34.17 | Qwell | ~jbot |
| 03:34.19 | jbot | jbot is probably only marginally useful at best, He got a C- on his Turing Test |
| 03:34.43 | N9URK | Qwell: thanks |
| 03:35.06 | N9URK | ~jbot help |
| 03:35.32 | Qwell | ~help |
| 03:35.47 | N9URK | yeah, I got it. tnx |
| 03:36.51 | SomeOne1 | ~book |
| 03:36.53 | jbot | it has been said that book is a book called Asterisk: The Future of Telephony which is found at http://www.asteriskdocs.org/modules/tinycontent/index.php?id=11 |
| 03:36.53 | SomeOne1 | ~sex |
| 03:36.55 | jbot | updatedb; locate; talk; date; cd; strip; look; touch; finger; unzip; uptime; gawk; head; apt-get install condom; mount; fsck; gasp; more; yes; yes; yes; more; umount; apt-get remove --purge condom; make clean; sleep, or super extractor, http://sf.net/projects/sex/ |
| 03:37.00 | SomeOne1 | jaime_bon: que paso amigo |
| 03:37.08 | SomeOne1 | jaime_bon: un poco espanol |
| 03:37.15 | SomeOne1 | para mi |
| 03:37.22 | *** join/#asterisk ManxPower (n=manxpowe@2.sub-75-203-79.myvzw.com) |
| 03:39.54 | jaime_bon | esque soy provedor de internet inalambrico, y necesito vender telefonia ip |
| 03:40.19 | jaime_bon | necesito una tarjeta que soporte 24 lineas.. |
| 03:40.54 | *** join/#asterisk EyeCue (n=eyecue@unaffiliated/eyecue) |
| 03:41.19 | jaime_bon | y al cliente ponerle un linksys ATA |
| 03:41.25 | jaime_bon | y asi pueda tener una linea telefonica |
| 03:42.19 | jaime_bon | im a wireless Internet Services Provider and i need sell IP Phone Lines |
| 03:42.38 | sweeper | jaime_bon: quieres una trajeta de T1 |
| 03:42.56 | sweeper | te recommendaria comprar una de dos connexiones de t1 |
| 03:43.17 | sweeper | eso lo vas a connectar a un banco de canale |
| 03:43.19 | jaime_bon | pero uso lineas analogicas |
| 03:43.25 | sweeper | aja |
| 03:43.35 | sweeper | por eso el banco de canales |
| 03:43.54 | sweeper | quieres algo como el adit600 |
| 03:44.18 | sweeper | beneficio de esto es que te hace mucho mas facil crecer, y es una plataforma muy estable |
| 03:45.58 | jaime_bon | pero no es asterisk verdad |
| 03:46.16 | sweeper | se usa con asterisk |
| 03:46.59 | jaime_bon | aaa ok osea de la tarjeta asterisk va conectado al adit600 |
| 03:47.04 | sweeper | aja |
| 03:47.12 | jaime_bon | las lineas llegan al adit 600 |
| 03:47.17 | jaime_bon | y de ahi al asterisk.. |
| 03:47.21 | sweeper | eso |
| 03:47.25 | jaime_bon | aaa |
| 03:47.33 | jaime_bon | y que tarjeta asterisk me recomiendas para esto |
| 03:48.08 | N9URK | yo tengo un gato en mis pantalones |
| 03:48.43 | sweeper | bueno, tienes 3 opciones |
| 03:48.54 | sweeper | carta de un t1, 2, o 4 |
| 03:49.19 | sweeper | tienes que ver cuanto vas a crecer, y a que velocidad |
| 03:49.54 | sweeper | el adit 600 puede soportar 48 canales |
| 03:50.02 | sweeper | con todas sus tarjetas |
| 03:50.12 | jaime_bon | aa entiendo |
| 03:50.28 | sweeper | si vas a crecer rapido, te recomendaria de una vez comprar la tarjeta de 2 t1 |
| 03:50.35 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 03:50.37 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 03:50.42 | sweeper | porque con eso puedes llenar el adit mientras vas creciendo |
| 03:50.44 | jaime_bon | si, eso voy a hacer |
| 03:51.03 | jaime_bon | las lineas que llegan a el adit son fxs? |
| 03:51.16 | jaime_bon | lo que pasa esque encontre un adit 600 que es para 15 fxs.. |
| 03:51.20 | sweeper | puedes comprar las que quieras |
| 03:51.27 | jaime_bon | ese no me sirve verdad por que las lineas son fxo |
| 03:51.37 | sweeper | mmm |
| 03:51.39 | sweeper | un rato |
| 03:51.54 | sweeper | tus lineas, van a telefonos, o vienen de la telefonica? |
| 03:52.02 | BSDTech | back |
| 03:52.05 | jaime_bon | mis lineas vienen de la telefonica |
| 03:52.12 | BSDTech | mac&cheese in hand |
| 03:52.47 | sweeper | ya, entonces si, tu quieres fxo |
| 03:52.52 | sweeper | pero una pregunta... |
| 03:53.00 | sweeper | dices que vas a tener 24 lines? |
| 03:53.00 | SomeOne1 | me gusta queso en el banyo con tu madre |
| 03:53.02 | sweeper | *lineas |
| 03:53.12 | SomeOne1 | i like cheese in the bathroom with your mother |
| 03:53.13 | jaime_bon | si |
| 03:53.16 | BSDTech | take it to #asterisk-spanish |
| 03:53.21 | SomeOne1 | jaime_bon: me gusta queso en el banyo con tu madre |
| 03:53.31 | sweeper | ya...entonces, porque no pedirle un t1 a la telefonica? |
| 03:53.43 | sweeper | te ahorras el costo del adit600 |
| 03:54.33 | jaime_bon | lo que pasa esque encontre una telefonica que ofrese buen servicio y bajo costo por linea pero me entrega en analogicas |
| 03:54.43 | sweeper | mmmm |
| 03:55.23 | sweeper | les has hablado? porque me parece que para tantas lineas, a ellos les sale mas barato correr una t1 |
| 03:55.41 | jaime_bon | si, ya hable con ellos |
| 03:55.53 | jaime_bon | pero insisten en analogicas.. |
| 03:56.04 | sweeper | bueno pues, alli quedas |
| 03:56.15 | Nugget | estoy un hombre cansado. |
| 03:56.27 | sweeper | con respecto al adit600, puedes comprar tarjetas de fxo o fxs |
| 03:56.27 | SomeOne1 | NO ME DIGAS |
| 03:56.36 | SomeOne1 | TU MADRE ES ME QUESO |
| 03:56.56 | jaime_bon | aaa ok entonces compro el adit 600 y ya nomas le voy poniendo tarjetas FXO |
| 03:57.09 | sweeper | aja |
| 03:57.45 | SomeOne1 | ANSWER ME SPANIARDS! |
| 03:58.50 | mishehu | "tengo el gato en los pantalones!" "Uhm, you just said you have a cat in your pants..." --Blue Streak |
| 03:58.57 | ManxPower | Isn't it like 5am in Spain? |
| 04:00.04 | jaime_bon | mire, vi un adit600 en ebay |
| 04:00.06 | jaime_bon | http://cgi.ebay.com/CAC-Carrier-Access-Adit-600-TDM-Controller-Dual-V-35_W0QQitemZ330073818569QQihZ014QQcategoryZ11175QQssPageNameZWDVWQQrdZ1QQcmdZViewItem |
| 04:00.07 | jaime_bon | ese es? |
| 04:00.25 | SomeOne1 | these spainards are paying no attention to us |
| 04:00.30 | SomeOne1 | so lets ingore them |
| 04:00.43 | ManxPower | jaime_bon: I prefer Adtran |
| 04:01.09 | ManxPower | Specifically the Adtran Total Access 750 (TA750) |
| 04:02.04 | jaime_bon | http://cgi.ebay.com/ADTRAN-TOTAL-ACCESS-750-LOADED-FXS-PSU-BCU-TA750_W0QQitemZ270078050278QQihZ017QQcategoryZ80226QQssPageNameZWDVWQQrdZ1QQcmdZViewItem |
| 04:02.08 | jaime_bon | this like you? |
| 04:02.48 | *** join/#asterisk anthm (n=anthm@CPE-72-131-113-50.wi.res.rr.com) |
| 04:02.48 | *** mode/#asterisk [+o anthm] by ChanServ |
| 04:07.23 | *** join/#asterisk Igbothom_III (n=Hilton@office.quarkit.com.au) |
| 04:07.45 | *** join/#asterisk [hC] (n=hardcore@70.68.142.245) |
| 04:12.18 | BSDTech | ok who is here I need some one to check something |
| 04:13.16 | *** join/#asterisk FaithX (n=faithful@ns.linuxterminal.com) |
| 04:22.47 | dorphalsig | Hello. |
| 04:22.49 | dorphalsig | Anybody here? |
| 04:23.20 | dorphalsig | I'm trying to get the H323 channels on asterisk 1.4 to work but I cant even see them in the channeltype definition |
| 04:23.25 | dorphalsig | (the module is loaded tho) |
| 04:23.31 | dorphalsig | any ideas what can be wrong? |
| 04:29.57 | *** join/#asterisk [hC] (n=hardcore@70.68.142.245) |
| 04:30.43 | *** join/#asterisk lowlevel (n=Stuart@CPE000e0c057fad-CM000f9f7d6742.cpe.net.cable.rogers.com) |
| 04:35.40 | *** join/#asterisk RoyK (n=roy@217-175-39.100710.adsl.tele2.no) |
| 04:37.12 | *** join/#asterisk Abydos313 (i=xnomar@ppp-71-136-22-241.dsl.irvnca.pacbell.net) |
| 04:41.18 | rene- | jajaa |
| 04:41.29 | rene- | que divertido asterisk en español |
| 04:42.01 | jaime_bon | jaja |
| 04:43.47 | dorphalsig | a ver si en español si ... |
| 04:44.09 | dorphalsig | estoy tratando de tener canales h323 en asterisk 1.4 |
| 04:44.12 | dorphalsig | logro compilar todo |
| 04:44.15 | dorphalsig | y cargo el .so |
| 04:44.18 | ManxPower | jaime_bon: Yes. That device looks good |
| 04:44.41 | dorphalsig | xo no me aparece el tipo de canal h323 |
| 04:45.19 | jaime_bon | thanxs manxpower |
| 04:46.00 | ManxPower | jaime_bon: Because the device will never connect to telecom/PTT, you can use T-1 version to connect to Asterisk. You should look for FXO/FXS compatibility with your country's telecom standartds |
| 04:46.34 | jaime_bon | aaa oks |
| 04:50.33 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 04:50.34 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 04:52.35 | intralanman | what should this match? exten => _unassigned., |
| 04:53.12 | intralanman | am i missing something or shouldn't it match anything that starts with unassigned? |
| 04:56.43 | SomeOne1 | what the heck if like |
| 04:56.49 | SomeOne1 | cant you do like |
| 04:57.25 | SomeOne1 | Dial(SIP/blah@blah,30,L(5)) |
| 04:57.34 | SomeOne1 | would that limit the call to 5 seconds? |
| 04:57.42 | SomeOne1 | or 5 minutes? |
| 04:57.43 | SomeOne1 | or what |
| 04:57.52 | dorphalsig | doesnt the wiki say? |
| 04:57.58 | dorphalsig | FAX "Enable Fax support" on \ |
| 04:58.00 | dorphalsig | ack |
| 04:58.00 | SomeOne1 | it says "ms" |
| 04:58.05 | dorphalsig | milliseconds |
| 04:58.07 | SomeOne1 | wtf does "ms" mean |
| 04:58.12 | SomeOne1 | well i tried it with 5 |
| 04:58.16 | SomeOne1 | but it doesnt time out |
| 04:58.26 | sbingner | milisecond |
| 04:58.41 | SomeOne1 | how many seconds in a milisecond |
| 04:58.45 | intralanman | yeah, you probably want something like 5000 |
| 04:58.55 | intralanman | 1000ms = 1 second |
| 04:58.55 | dorphalsig | 1000 milliseconds = 1 second |
| 04:59.06 | dorphalsig | Come on |
| 04:59.17 | dorphalsig | somebody help me out with my h323 issue damnit |
| 05:00.01 | SomeOne1 | HELL YES IT WORKED!@*&^*!&@# |
| 05:00.06 | SomeOne1 | I LOVE YOU ALL! |
| 05:00.07 | SomeOne1 | GOOD NIGHT! |
| 05:00.14 | sbingner | send hookers |
| 05:00.20 | intralanman | and beer |
| 05:00.39 | intralanman | maybe even some little green leaves |
| 05:00.51 | intralanman | you know we're gonna need aloe after the hookers and beer |
| 05:00.52 | intralanman | lol |
| 05:00.54 | SomeOne1 | mary jane? |
| 05:01.00 | SomeOne1 | heh |
| 05:01.03 | SomeOne1 | thanks guys |
| 05:01.04 | SomeOne1 | 'night |
| 05:01.17 | sbingner | wtf no hookers? |
| 05:01.25 | dorphalsig | no green leaves!! |
| 05:02.47 | *** join/#asterisk BSDTech (n=RNeese@ppp-69-238-75-25.dsl.irvnca.pacbell.net) |
| 05:05.40 | *** join/#asterisk BSDTech (n=RNeese@ppp-69-238-75-25.dsl.irvnca.pacbell.net) |
| 05:06.04 | dorphalsig | Hello. I've installed asterisk 1.4 (with addons) and have succesfully compiled chan_ooh323.so. yet I cant see H323 channels in the channeltypes |
| 05:06.11 | dorphalsig | can anybody give me a hand? |
| 05:09.57 | *** join/#asterisk BSDTech (n=RNeese@ppp-69-238-75-25.dsl.irvnca.pacbell.net) |
| 05:10.10 | WAudette | Corydon76-home: Are you back? |
| 05:10.25 | Corydon76-home | Yes, but I'm tired right now |
| 05:10.32 | Corydon76-home | Maybe tomorrow morning |
| 05:10.33 | WAudette | No problem. |
| 05:10.41 | WAudette | I'll look you up then. |
| 05:11.10 | WAudette | You never let me know what you wanted for a donation. |
| 05:13.20 | Corydon76-home | I don't demand payment for things I find interesting, but if you want to, you can send me a donation |
| 05:19.04 | *** join/#asterisk CunningPike (n=CunningP@S010600095b33697f.vc.shawcable.net) |
| 05:19.46 | *** join/#asterisk |dennis| (n=dennis@200.32.233.82) |
| 05:30.29 | *** join/#asterisk Stephnie (i=Stephnie@u15157627.onlinehome-server.com) |
| 05:30.31 | Stephnie | hello |
| 05:31.05 | Stephnie | I want to run an AGI script through .call file ... any help? |
| 05:49.23 | ManxPower | Have the .call file run an extension or dial via Local/extension@context, which would run the AGI |
| 05:50.24 | *** join/#asterisk niZon (i=bleh@S0106beefd4cecc3d.wp.shawcable.net) |
| 05:50.32 | dorphalsig | HI |
| 05:50.33 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 05:50.33 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 05:50.42 | dorphalsig | I cant get h323 channels installed |
| 05:50.43 | dorphalsig | I dunno why |
| 05:50.52 | dorphalsig | I follow the readme but no luck |
| 05:51.53 | ManxPower | Which of the 5 or so H323 channel drivers did you try? |
| 05:52.18 | dorphalsig | The one in channels/h323 of the * 1.4 |
| 05:52.31 | dorphalsig | the readme says |
| 05:52.45 | dorphalsig | get openh323 and pwdlib |
| 05:52.56 | ManxPower | Try the one in asterisk-addons |
| 05:52.58 | dorphalsig | and then just make in the channels/h323 dir |
| 05:53.07 | ManxPower | ooh323, I think, |
| 05:53.08 | dorphalsig | I made both actually |
| 05:53.23 | ManxPower | it prolly says to get SPECIFIC VERSIONS of openh323 and pwlib |
| 05:53.35 | dorphalsig | yeah, and I got those =) |
| 05:54.12 | ManxPower | post the errors to asterisk-users mailing lists, since your search of that mailing list was not helpful. |
| 05:54.27 | dorphalsig | there are no errors |
| 05:54.32 | dorphalsig | it just wont load |
| 05:54.51 | dorphalsig | 69-64-78-118*CLI> show channeltypes |
| 05:54.54 | ManxPower | and when you load chan_h323.so in the CLI? |
| 05:55.43 | dorphalsig | [root@69-64-78-118 h323]# asterisk -rx "show modules" |grep 323 |
| 05:55.43 | dorphalsig | chan_ooh323.so Objective Systems H323 Channel 0 |
| 05:56.55 | ManxPower | looks right to me |
| 05:56.55 | dorphalsig | I load it and nothing happens |
| 05:57.15 | ManxPower | report THAT as a bug on bugs.digium.com |
| 05:57.16 | dorphalsig | [root@69-64-78-118 h323]# asterisk -rx "show channeltypes" |grep 323 |
| 05:57.16 | dorphalsig | [root@69-64-78-118 h323]# |
| 05:57.21 | ManxPower | it should be in the channeltypes |
| 05:57.45 | ManxPower | have you MANUALLY looked at the output of channeltypes? |
| 05:58.24 | dorphalsig | yes |
| 05:58.35 | Stephnie | ManxPower: sorry I was away ...let me check Local/extension@context, |
| 05:58.38 | *** join/#asterisk Defraz (n=t0tal@24-116-159-197.cpe.cableone.net) |
| 05:58.39 | dorphalsig | and no luck |
| 05:59.03 | dorphalsig | ManxPower -> You think I should try the svn and see if it works for me? |
| 05:59.21 | dorphalsig | or report the bug |
| 05:59.25 | dorphalsig | and stop bugging |
| 06:00.20 | *** join/#asterisk techie (n=techie@c-67-181-184-170.hsd1.ca.comcast.net) |
| 06:05.29 | *** join/#asterisk osiris (n=osiris@c-71-205-27-131.hsd1.mi.comcast.net) |
| 06:06.36 | rene- | i am doing a transfer out of a queue using # and not a sip transfer |
| 06:06.53 | Stephnie | ManxPower : it works....thanks |
| 06:07.01 | rene- | the agent keeps bridged, is there a way the agent can be out of the call after has transferred |
| 06:07.11 | *** part/#asterisk Stephnie (i=Stephnie@u15157627.onlinehome-server.com) |
| 06:07.14 | rene- | the agent is a local dynamic sip device |
| 06:08.03 | rene- | it is very bad since the agent will be reported as in use and will not take calls |
| 06:08.13 | rene- | until the transferred call is finished |
| 06:18.10 | *** join/#asterisk BSDTech (n=RNeese@ppp-69-238-75-25.dsl.irvnca.pacbell.net) |
| 06:18.15 | file | dorphalsig: are you still there? |
| 06:18.32 | *** join/#asterisk techie (n=techie@c-67-181-184-170.hsd1.ca.comcast.net) |
| 06:20.38 | *** join/#asterisk blitzrage (n=blitzrag@asterisk/documenteur-extraordinaire/blitzrage) |
| 06:20.53 | blitzrage | y0 |
| 06:21.01 | file | blitzrage: also, away with you |
| 06:22.00 | *** join/#asterisk obnauticus (i=asd@c-24-21-116-29.hsd1.mn.comcast.net) |
| 06:22.13 | BSDTech | http://cgi.ebay.com/PQI-512MB-DiskOnModule-Disk-On-Module-DOM-DJ0512M44NK0_W0QQitemZ180073347023QQihZ008QQcategoryZ51076QQssPageNameZWDVWQQrdZ1QQcmdZViewItem |
| 06:22.28 | BSDTech | great for embeded devices |
| 06:27.31 | *** join/#asterisk osiris (n=osiris@c-71-205-27-131.hsd1.mi.comcast.net) |
| 06:33.45 | *** join/#asterisk shy__guy (i=jeremy_g@c213-100-17-43.swipnet.se) |
| 06:35.55 | *** join/#asterisk BSDTech (n=RNeese@ppp-69-238-75-25.dsl.irvnca.pacbell.net) |
| 06:41.10 | *** join/#asterisk L|NUX (n=linux@unaffiliated/lnux/x-10290) |
| 06:43.02 | *** part/#asterisk techie (n=techie@c-67-181-184-170.hsd1.ca.comcast.net) |
| 06:50.33 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 06:50.33 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 06:59.12 | *** join/#asterisk sahafeez (n=sahafeez@ip68-6-215-70.sd.sd.cox.net) |
| 07:03.07 | *** join/#asterisk [hC] (n=hardcore@70.68.142.245) |
| 07:05.13 | *** join/#asterisk Cyon (n=cyon@cyons.net) |
| 07:18.28 | *** join/#asterisk DaveCanoe (n=Dave@canoe404.dclg.ca) |
| 07:27.56 | *** join/#asterisk obiwanmikenolte (n=obiwanmi@71-10-180-68.dhcp.stls.mo.charter.com) |
| 07:32.10 | *** join/#asterisk Ritalin2 (n=dave@c-68-47-199-178.hsd1.tn.comcast.net) |
| 07:34.51 | Ritalin2 | are we awake? |
| 07:35.22 | Cyon | God no. It's 2:35 am, why would anyone (in this tz at least) be awake? |
| 07:37.36 | Ritalin2 | i just got home from work |
| 07:37.42 | Ritalin2 | we're in the same tz |
| 07:42.19 | *** join/#asterisk jeebusroxors (n=jeebusro@cpe-75-80-231-237.dc.res.rr.com) |
| 07:47.17 | *** join/#asterisk dwmw2_gone (i=ctrlprox@baythorne.infradead.org) |
| 07:50.33 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 07:50.33 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 07:51.36 | *** join/#asterisk CrashHD (i=CrashHD@c-67-182-167-222.hsd1.ca.comcast.net) |
| 07:56.18 | *** join/#asterisk vader-- (n=me@c-71-226-201-15.hsd1.nj.comcast.net) [NETSPLIT VICTIM] |
| 07:56.18 | *** join/#asterisk bkw__ (n=brian@ip68-0-120-100.tu.ok.cox.net) [NETSPLIT VICTIM] |
| 07:56.18 | *** join/#asterisk `Sean (i=Un1x@CPE000c148d127c-CM00140458831c.cpe.net.cable.rogers.com) [NETSPLIT VICTIM] |
| 07:56.18 | *** join/#asterisk GiantPickle (n=GiantPic@S0106006008bd147d.gv.shawcable.net) [NETSPLIT VICTIM] |
| 07:56.18 | *** join/#asterisk Juggie (n=Juggie@CPE00c049d9f271-CM000a73a18a20.cpe.net.cable.rogers.com) |
| 07:56.18 | *** join/#asterisk Flusher (i=flusher@filer.euroserv.com) [NETSPLIT VICTIM] |
| 07:56.18 | *** join/#asterisk infernix (i=nix@spirit.infernix.net) [NETSPLIT VICTIM] |
| 07:56.18 | *** join/#asterisk fnordus (n=dnall@24.85.128.203) [NETSPLIT VICTIM] |
| 07:56.18 | *** join/#asterisk tzafrir (n=tzafrir@62.90.10.53) [NETSPLIT VICTIM] |
| 07:56.18 | *** join/#asterisk max_______ (i=max__@ts.bestserversllc.net) [NETSPLIT VICTIM] |
| 07:56.18 | *** join/#asterisk bcnl (n=mike@24.86.64.144) [NETSPLIT VICTIM] |
| 07:56.19 | *** join/#asterisk SwK[Work] (n=SwK@24.214.206.254) [NETSPLIT VICTIM] |
| 07:56.19 | *** join/#asterisk rajiv|work (n=rajiv@gentoo/developer/rajiv) [NETSPLIT VICTIM] |
| 07:56.19 | *** join/#asterisk squish102 (n=squish10@cpe-024-074-100-250.carolina.res.rr.com) [NETSPLIT VICTIM] |
| 07:56.19 | *** join/#asterisk jart (n=user@ool-43551046.dyn.optonline.net) [NETSPLIT VICTIM] |
| 07:56.19 | *** join/#asterisk Tebi (n=rantis@gw.aller.fi) [NETSPLIT VICTIM] |
| 07:56.19 | *** join/#asterisk pjz (n=pj@zachs.place.org) [NETSPLIT VICTIM] |
| 07:56.19 | *** join/#asterisk kennyt (n=ken@nurve.tossell.net) [NETSPLIT VICTIM] |
| 07:56.19 | *** join/#asterisk Elwell (n=andrew@87.127.71.46) [NETSPLIT VICTIM] |
| 07:56.19 | *** join/#asterisk aydiosmio (i=aydiosmi@216.93.240.178) [NETSPLIT VICTIM] |
| 07:56.19 | *** join/#asterisk Nivex (n=kjotte@user-0ce2nsk.cable.mindspring.com) [NETSPLIT VICTIM] |
| 07:56.19 | *** join/#asterisk FWP (n=FWP@unaffiliated/fwp) [NETSPLIT VICTIM] |
| 08:00.54 | Ritalin2 | splitty mcsplitters |
| 08:03.23 | *** join/#asterisk apardo (n=apardo@87.217.145.40) |
| 08:04.36 | *** join/#asterisk kerlnel20 (n=kerlnel2@202.137.121.84) |
| 08:04.40 | kerlnel20 | hi there |
| 08:05.14 | kerlnel20 | would it be possible to make outgoing calls by just using data modem used for dial up? |
| 08:05.25 | kerlnel20 | that model i will connect it to my pots |
| 08:05.48 | *** join/#asterisk [hC] (n=hardcore@S0106000fb51cc225.vf.shawcable.net) |
| 08:06.52 | Ritalin2 | kernel20: even if you had enough bandwidth you'd have latency problems |
| 08:07.15 | kerlnel20 | no not that one |
| 08:07.30 | kerlnel20 | i want to create a home based pbx |
| 08:07.45 | kerlnel20 | actually my asterisk is not connected to internet |
| 08:07.59 | Ritalin2 | well you could setup asterisk and attempt the inter-asterisk exchange |
| 08:08.18 | Ritalin2 | part of the asterisk demo |
| 08:08.22 | kerlnel20 | from my sip phone i will have numbers to dial in order to make outside calls to pstn |
| 08:09.00 | Ritalin2 | do you have a VoIP account of some sort? |
| 08:09.19 | kerlnel20 | yes |
| 08:09.26 | kerlnel20 | my asterisk is already up |
| 08:09.34 | kerlnel20 | problem i want to connect POTS |
| 08:09.41 | *** join/#asterisk bkruse_home (n=kruz@69.73.127.92) |
| 08:09.43 | kerlnel20 | so that i can make outside calls |
| 08:10.45 | Ritalin2 | I can make calls with my VoIP account to standard telephone numbers |
| 08:10.58 | kerlnel20 | how? |
| 08:11.10 | kerlnel20 | did u purchase x100P from digium? |
| 08:11.16 | kerlnel20 | i want to use data modem |
| 08:11.20 | kerlnel20 | would it be possible? |
| 08:11.21 | Ritalin2 | the VoIP provider does the PSTN termination |
| 08:11.46 | Ritalin2 | it goes my house->internet->my VoIP provider->outside world |
| 08:11.46 | kerlnel20 | what? |
| 08:11.57 | kerlnel20 | no not that one |
| 08:11.57 | Ritalin2 | i think i'm confused a little by what you want to do |
| 08:12.10 | Ritalin2 | you want to use the same POTS line to make data calls and voice calls? |
| 08:12.24 | kerlnel20 | sip phone -> asterisk with pci modem card -> PSTN |
| 08:12.28 | kerlnel20 | or POTS |
| 08:12.39 | Ritalin2 | oh, yeah you can do it with the x100p |
| 08:13.02 | Ritalin2 | the one I had was a clone that I got from ebay for $10 or so. it didn't last very long |
| 08:13.17 | kerlnel20 | what abount not x100p |
| 08:13.22 | Ritalin2 | now I have a TDM400P but I use it to hook up analog phones |
| 08:13.26 | kerlnel20 | i want to use pci data modem |
| 08:13.36 | kerlnel20 | would it be possible? |
| 08:13.44 | Ritalin2 | it is possible with the x100p |
| 08:13.56 | kerlnel20 | my question is pci data modem |
| 08:14.00 | kerlnel20 | i know x100p |
| 08:14.18 | Ritalin2 | depends if the pci data modem in question is supported by the zaptel driver |
| 08:14.35 | Ritalin2 | do you have a specific modem in mind? |
| 08:15.58 | kerlnel20 | i have a dlink one |
| 08:16.03 | kerlnel20 | does it supported? |
| 08:16.19 | kerlnel20 | what should be in my dial plan in order to call? |
| 08:16.26 | kerlnel20 | is it the modem.conf? |
| 08:16.32 | kerlnel20 | and extensions.conf? |
| 08:16.57 | kerlnel20 | actually it is a v.92 modem |
| 08:18.02 | kerlnel20 | how to check if it is supported by zaptel? |
| 08:18.57 | Ritalin2 | i'm looking |
| 08:21.07 | Ritalin2 | doesn't appear to |
| 08:21.22 | Ritalin2 | x100p clones are really cheap. but the best way to do it is with an ATA |
| 08:22.23 | kerlnel20 | actually i am located in the philippines |
| 08:22.28 | kerlnel20 | very hard for me to by x100p |
| 08:22.42 | kerlnel20 | it is order basis |
| 08:22.44 | Ritalin2 | looks like Tormenta cards and Wildcat cards (such as the X100P) |
| 08:22.57 | kerlnel20 | thats why i prefer v92 modem |
| 08:23.06 | kerlnel20 | because i can get it anytime |
| 08:23.54 | Ritalin2 | is it a voice modem? |
| 08:24.20 | Ritalin2 | what specific model |
| 08:24.33 | Ritalin2 | A modem with the following chipsets should work: |
| 08:24.33 | Ritalin2 | Intel 537PG and 537PU |
| 08:24.33 | Ritalin2 | Ambient MD3200 |
| 08:24.33 | Ritalin2 | Motorola 62802 |
| 08:25.23 | Ritalin2 | the Motorola modem is what I had. you can buy them all day long on ebay |
| 08:26.18 | kerlnel20 | ebay is only for US |
| 08:26.23 | kerlnel20 | i am in philippines |
| 08:26.27 | Ritalin2 | http://www.voip-info.org/tiki-index.php?page=X100P+clone |
| 08:26.31 | Ritalin2 | that's what you are looking for |
| 08:28.21 | Ritalin2 | these are more flexible (analog telephone adapaters) http://www.voip-info.org/wiki/view/Analog+Telephone+Adapters |
| 08:28.41 | Ritalin2 | what you are looking for is something with at least one FXO port |
| 08:28.49 | kerlnel20 | yeah |
| 08:28.57 | Ritalin2 | how are you going to talk to asterisk from inside your house? |
| 08:29.54 | kerlnel20 | through xlite |
| 08:30.00 | kerlnel20 | or sip phone |
| 08:30.07 | bkruse_home | WARNING YOUR ABOUT TO GO ON THE RIDE OF YOUR LIFE |
| 08:30.11 | Ritalin2 | that'll work |
| 08:30.39 | kerlnel20 | that is why i only need a data/voice modem |
| 08:31.09 | bkruse_home | ~ggw |
| 08:31.12 | Ritalin2 | as long as it has one of those DSPs listed it should be able to be configured |
| 08:31.33 | *** join/#asterisk frk2 (n=fkhan@202.5.145.13) |
| 08:31.34 | frk2 | guys, i have the weirdest stuff to say regarding my TE110P |
| 08:31.34 | frk2 | :) |
| 08:31.45 | Ritalin2 | weird good or weird funny |
| 08:31.47 | Ritalin2 | or weird bad |
| 08:31.50 | frk2 | weird BAD |
| 08:32.01 | Ritalin2 | :( |
| 08:32.16 | bkruse_home | frk2: explain |
| 08:33.15 | Ritalin2 | what's the command to see overhead of each codec? |
| 08:33.42 | bkruse_home | show translation |
| 08:33.46 | Ritalin2 | thanks bk |
| 08:33.53 | bkruse_home | oh wait |
| 08:34.08 | bkruse_home | show translation shows "load" for transcoding between codecs |
| 08:34.14 | bkruse_home | you mean like IP overhead per codec? |
| 08:34.23 | Ritalin2 | no i wanted the transcoding overhead |
| 08:34.27 | bkruse_home | kk, cool |
| 08:34.30 | bkruse_home | then thats it ;] |
| 08:34.33 | kerlnel20 | is zapata.conf or modem.conf i will edit? |
| 08:34.38 | frk2 | okay |
| 08:34.38 | kerlnel20 | Ritalin2? |
| 08:34.40 | bkruse_home | or core show translation for 1.4 |
| 08:34.47 | bkruse_home | kerlnel20: im guessing zapata.conf |
| 08:34.48 | frk2 | my span keeps going up and down on the te110p |
| 08:34.53 | frk2 | when the span is down, |
| 08:34.55 | frk2 | calls dont disconnect |
| 08:34.59 | frk2 | inbound calls work |
| 08:35.06 | frk2 | but outbound calls show 'congestion' |
| 08:35.19 | Ritalin2 | kernel20: /etc/asterisk/zapata.conf and /etc/zaptel.conf |
| 08:35.23 | bkruse_home | you sure its not a "user error" ? |
| 08:35.30 | bkruse_home | frk2: can i ssh in and look? |
| 08:35.36 | bkruse_home | what framing, wher you getting timing from |
| 08:35.41 | frk2 | exactly |
| 08:35.43 | frk2 | now |
| 08:35.43 | bkruse_home | esf b8zs? |
| 08:35.52 | frk2 | with the timing, it was set to telco (1) |
| 08:35.58 | frk2 | i changed it to Local (0) |
| 08:36.02 | bkruse_home | k |
| 08:36.04 | frk2 | and its been fine after that |
| 08:36.07 | frk2 | doesnt make sense!!!!! |
| 08:36.14 | bkruse_home | can i look at it? |
| 08:36.38 | frk2 | its on a customer site dude |
| 08:37.12 | bkruse_home | hmm |
| 08:38.42 | frk2 | okay never mind |
| 08:38.46 | frk2 | went down up again |
| 08:38.49 | frk2 | damnit |
| 08:38.51 | Strom_M | is it a PRI? |
| 08:38.54 | frk2 | Yes |
| 08:39.00 | Strom_M | or is ita straight channelized t1 |
| 08:39.27 | Strom_M | which provider |
| 08:40.19 | sevard | let's get some shoes. |
| 08:40.21 | sevard | shoes. |
| 08:40.27 | Strom_M | omg shoes |
| 08:40.40 | sevard | these shoes suck |
| 08:40.45 | Strom_M | these shoes rule |
| 08:40.50 | sevard | THESE SHOES UCK |
| 08:40.52 | sevard | +S |
| 08:41.00 | Strom_M | these shoes are three hundred dollars |
| 08:41.03 | frk2 | dude its a PRI |
| 08:41.05 | frk2 | it works man |
| 08:41.09 | sevard | THESE SHOES ARE THREE HUNDRED FUCKING DOLLARS |
| 08:41.21 | frk2 | just keeps going up and down |
| 08:41.21 | Strom_M | frk2, who is the provider for the PRI? |
| 08:41.43 | sevard | Strom_M: Both chedar and I are going "how the fuck does he know that?" |
| 08:41.57 | Strom_M | sevard, my fifteen year old sister linked me to the youtube video |
| 08:42.07 | sevard | excellent. |
| 08:42.35 | Strom_M | frk2, who is the PRI provider? do you know? |
| 08:42.40 | *** join/#asterisk tsurko (n=tsurko@vpn-pppoe-213-240-242-237.megalan.bg) |
| 08:42.44 | sevard | BTW, SF weather > LA weather, but silly cheddar booked our hostel in TenerLoin |
| 08:42.49 | sevard | TenderLoin |
| 08:42.58 | frk2 | its in Pakistan so i doubt you would know dude |
| 08:43.12 | bkruse_home | oh.......... |
| 08:43.18 | Ritalin2 | someone link me to the youtube video too |
| 08:43.21 | Strom_M | frk2, you know what, I don't have to help you either with an attitude like that |
| 08:45.25 | frk2 | dude theres no attitude |
| 08:45.32 | frk2 | you think its the provider? |
| 08:45.49 | Strom_M | I'm trying to figure out where the problem might be |
| 08:45.56 | frk2 | okay.. its a E1 |
| 08:46.03 | Strom_M | what's the buildout between the smartjack and the CPE? |
| 08:46.12 | frk2 | i have 4 more of these from the same provider working on a TE110p without issues |
| 08:46.21 | Strom_M | and is it provided as straight repeatered E1 or is it VDSL? |
| 08:46.25 | Strom_M | er, HDSL |
| 08:46.25 | frk2 | i've just set it to zero |
| 08:46.29 | frk2 | its HDSL |
| 08:46.46 | *** join/#asterisk [hC] (n=hardcore@S0106000fb51cc225.vf.shawcable.net) |
| 08:46.51 | Strom_M | what's the buildout between the smartjack and the CPE? |
| 08:46.52 | *** join/#asterisk pa (n=Paolo@unaffiliated/pa) |
| 08:47.27 | *** join/#asterisk ghenry (n=ghenry@suretecsystems.plus.com) |
| 08:47.31 | sevard | night. |
| 08:47.59 | frk2 | i have it at zero |
| 08:48.07 | frk2 | its less than 2-3 feet |
| 08:48.07 | Strom_M | im not asking what you have it set at |
| 08:48.10 | Strom_M | ok |
| 08:48.24 | Strom_M | you've tried replacing the cable, right? |
| 08:48.29 | *** join/#asterisk dlynes_laptop (n=dlynes@S0106001346f7843f.vc.shawcable.net) |
| 08:48.38 | frk2 | yup |
| 08:48.40 | frk2 | multiple times |
| 08:48.51 | Strom_M | and you've done hard loopback tests on both the smartjack and the TE110P to verify those work without problem? |
| 08:50.23 | osiris | what would be the basic cpu/ram req.'s for running asterisk ? |
| 08:50.33 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 08:50.33 | Qwell | ~time |
| 08:50.36 | jbot | time is, like, 1 dimensional, or everlasting, an illusion, or 2007.01.13 8:50:36 GMT |
| 08:50.37 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 08:50.42 | Strom_M | osiris, depends on what you want to do with it |
| 08:50.56 | Strom_M | Qwell, I found myself looking for a Qwells Fargo this evening |
| 08:51.18 | Strom_M | it took me about two minutes to go 'no no no wait" |
| 08:51.20 | Qwell | How sued would I be if I started a bank named Qwell Fargo? |
| 08:51.31 | Strom_M | Qwell, i dunno |
| 08:51.32 | Qwell | or, Qwell Communications (shortened to Qwellcomm) |
| 08:51.47 | Strom_M | Pacific Qwell |
| 08:51.51 | Qwell | ha |
| 08:51.52 | Strom_M | QwellSouth |
| 08:51.52 | Qwell | I love it |
| 08:52.15 | Qwell | AT&Q? |
| 08:52.23 | Strom_M | eh, doesnt really work |
| 08:52.28 | Ritalin2 | your slogan could be "That's Qwell!" |
| 08:52.37 | Qwell | Strom_*: yeah.. |
| 08:52.51 | Qwell | nah |
| 08:52.59 | Qwell | if I started a company named QwellSouth... |
| 08:53.12 | Qwell | my official slogan would be "I don't have to care. I'm your telephone company." |
| 08:53.36 | Strom_M | i believe, sir, that it's "We don't care. We don't have to." |
| 08:53.51 | Qwell | well, I don't wanna get sued :P |
| 08:54.04 | bkruse_home | Qwell: go to sleep! |
| 08:54.10 | Qwell | you :p |
| 08:54.16 | Qwell | so |
| 08:54.18 | Qwell | oh |
| 08:54.19 | Qwell | my |
| 08:54.19 | Qwell | god |
| 08:54.26 | bkruse_home | Qwell: worky tommorrow? |
| 08:54.26 | Strom_M | shoes |
| 08:54.32 | Qwell | we went out downtown tonight... |
| 08:54.44 | bkruse_home | ~shoes |
| 08:54.46 | jbot | methinks shoes is something that strom_M rambles about |
| 08:54.46 | Qwell | and Crossroads (a bar) was reopening in a new location... |
| 08:54.56 | Strom_M | haha |
| 08:54.58 | Qwell | in the parking lot...where was a PBR truck |
| 08:55.04 | bkruse_home | :X |
| 08:55.04 | Qwell | (Pabst Blue Ribbon) |
| 08:55.09 | Qwell | I swear to god |
| 08:55.13 | Qwell | there was a tap on the back of the truck |
| 08:55.14 | Qwell | and |
| 08:55.15 | Qwell | I swear to god |
| 08:55.18 | Strom_M | ah, redneck beer |
| 08:55.21 | Qwell | it was connected to a keg |
| 08:55.29 | bkruse_home | !!!!!!!!!!!!!!!!!!!!!!! |
| 08:55.34 | Qwell | and it was...completely free |
| 08:55.35 | bkruse_home | Strom_M: best kind! |
| 08:55.38 | bkruse_home | Qwell: WZTNZEIOWNDWANDIWAs |
| 08:55.48 | Strom_M | pfft, give me a newcastle or a guinness |
| 08:55.48 | Ritalin2 | you know i was going to go on about how PBR isn't all that |
| 08:55.54 | Ritalin2 | but... free beer is free beer! |
| 08:56.00 | Qwell | Ritalin2: That's what I'm saying |
| 08:56.09 | Qwell | people were walking by, and we would tell them... |
| 08:56.21 | Qwell | and it took some serious convincing for them to believe that the truck was literally flowing beer |
| 08:56.35 | Qwell | it was kinda getting out of hand |
| 08:56.40 | Strom_M | heh |
| 08:56.44 | Ritalin2 | those are the best times |
| 08:56.56 | Qwell | what's funny though, is that the security guy that was right there...had NO idea |
| 08:56.59 | frk2 | Strom_M digium suggested a patlooptest |
| 08:57.01 | frk2 | came out fine |
| 08:57.05 | Qwell | people only found it at like 2am |
| 08:57.10 | frk2 | everything usb,sound is disabled on the Motherboard |
| 08:57.15 | frk2 | no interrupt sharing as well |
| 08:57.15 | Ritalin2 | haha like when we were partying for new years one year and this guy with a giant inflatable penis walks up to us. we thought it was funny so we hung out with him |
| 08:57.39 | Strom_M | frk2, what happens if you try the working circuit in this box and the flaky circuit in another box? |
| 08:57.55 | Strom_M | do the problems stay with the box or do they stay with the circuit |
| 08:58.21 | frk2 | thats the problem- I cant just 'play' around with a test pri :( |
| 08:58.35 | Strom_M | what do you mean? |
| 08:58.40 | Strom_M | you said you had three others there |
| 08:58.49 | frk2 | not there |
| 08:58.51 | frk2 | different clients |
| 08:58.59 | frk2 | different locations.. different exchanges also |
| 08:59.08 | Strom_M | well, that's different then |
| 08:59.13 | frk2 | possibly also using different vendors for their ISDN equipment... |
| 08:59.13 | Strom_M | hmm |
| 08:59.51 | *** part/#asterisk bkruse_home (n=kruz@69.73.127.92) |
| 08:59.53 | frk2 | is tghere any kind of a test i can do on the PRI? |
| 09:00.07 | Strom_M | have you done a hard loopback at the smartjack? |
| 09:00.23 | frk2 | by smartjack you mean the E1 card right? |
| 09:00.54 | Strom_M | well, im not familiar with the way it's done there, but assuming it's HDSL like it is here in california, you should see this: |
| 09:01.27 | Strom_M | -----HDSL-------[CARD]==[RJ48X]======YOUR CABLE=======[TE110P] |
| 09:01.38 | Qwell | RJ48? |
| 09:01.48 | frk2 | yes almost exactly like that |
| 09:01.53 | Strom_M | yeah, it's a special kind of jack that closes itself |
| 09:01.53 | frk2 | except its a rj-9 |
| 09:02.02 | Strom_M | ...RJ-9?! |
| 09:02.03 | Qwell | closes itself? |
| 09:02.15 | Strom_M | that's a four-conductor four-position modular plug |
| 09:02.20 | frk2 | and theres no 'card' |
| 09:02.22 | frk2 | more like |
| 09:02.24 | Strom_M | are you /certain/ about that? |
| 09:02.37 | frk2 | HDSL --- RJ9 --- RJ45 (e1) ---> te110p |
| 09:02.37 | Qwell | RJ9 is what handsets usually are, yes? |
| 09:02.47 | frk2 | thats rj-11 |
| 09:02.48 | Qwell | well |
| 09:02.48 | Strom_M | yes, RJ9 is a handset connector |
| 09:02.56 | frk2 | hang on |
| 09:02.58 | Strom_M | no, RJ-11 is the desk set, RJ-9 is the handset cord |
| 09:03.04 | frk2 | whats the 9-pin serial connector called? |
| 09:03.10 | Strom_M | DB-9 |
| 09:03.10 | Qwell | 2 position, 4 conductor? or do I have that backwards? |
| 09:03.11 | frk2 | its the 9-pin serial connect |
| 09:03.13 | frk2 | shit- yes |
| 09:03.14 | frk2 | DB-9 |
| 09:03.15 | frk2 | :) |
| 09:03.26 | Strom_M | jesus, frk2, don't scare me like that |
| 09:03.30 | *** join/#asterisk coppice (n=chatzill@129.168.17.210.dyn.pacific.net.hk) |
| 09:03.30 | Strom_M | Qwell, there can be no such thing |
| 09:03.32 | frk2 | sorry dude |
| 09:03.35 | Qwell | so, other way around |
| 09:03.45 | Strom_M | how does DB9 enter into it? |
| 09:03.45 | frk2 | im amazed that my shit has been running fine for an hour now |
| 09:03.47 | Qwell | conductor = wire, position = possibilities? |
| 09:03.50 | frk2 | it'll just randomly go boom |
| 09:03.58 | Qwell | it's late, and I'm a nub |
| 09:04.02 | frk2 | Its a tel-labs modem |
| 09:04.06 | frk2 | outputs a DB-9 |
| 09:04.12 | frk2 | cant help that now can i :P |
| 09:04.15 | Qwell | frk2: null? :P |
| 09:04.30 | frk2 | but we have the same arrangement at another client.. working flawlessly for a year |
| 09:04.36 | Strom_M | so the HDSL plugs into the "modem" thing, then you have a cable with a DB9 on one end and an RJ45 plug at the other? |
| 09:04.48 | frk2 | yes. its completely custom made |
| 09:04.53 | Strom_M | oh christ |
| 09:05.09 | frk2 | what the hell do i do man- tel-labs insists on making a DB-9 |
| 09:05.15 | Strom_M | premanufactured, or you made it yourself? |
| 09:05.15 | frk2 | i know of no pbx that takes a db-9 |
| 09:05.23 | frk2 | make it myself |
| 09:05.25 | frk2 | happened again |
| 09:05.36 | frk2 | i see this: |
| 09:05.37 | frk2 | Jan 13 14:05:16 NOTICE[14453]: chan_zap.c:8194 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 |
| 09:05.39 | frk2 | and then: |
| 09:05.46 | Strom_M | well, theres probably the source of your problem - bad cable |
| 09:05.51 | frk2 | Jan 13 14:05:24 WARNING[14453]: chan_zap.c:2287 pri_find_dchan: No D-channels available! Using Primary channel 16 as D-channel anyway! |
| 09:06.01 | Strom_M | do this |
| 09:06.09 | frk2 | <PROTECTED> |
| 09:06.09 | frk2 | Jan 13 14:05:27 WARNING[14453]: chan_zap.c:2287 pri_find_dchan: No D-channels available! Using Primary channel 16 as D-channel anyway! |
| 09:06.09 | frk2 | <PROTECTED> |
| 09:06.17 | Strom_M | stop flooding |
| 09:06.19 | frk2 | this repeats itself |
| 09:06.22 | frk2 | im not flooding |
| 09:06.26 | frk2 | controlled lines man :) |
| 09:06.33 | Strom_M | ~pb |
| 09:06.35 | jbot | extra, extra, read all about it, pb is a place to paste your stuff without flooding the channel - try http://pastebin.ca, or http://channels.debian.net/paste |
| 09:06.35 | frk2 | okay okay- im totally open to suggestions here |
| 09:06.44 | frk2 | i know of pastebin- just was too little |
| 09:06.55 | *** join/#asterisk TonyM (n=TonyM@softins.claranet.co.uk) |
| 09:06.58 | frk2 | so- any suggestions? |
| 09:07.17 | Strom_M | im thinking |
| 09:07.44 | frk2 | one more thing.. i changed the clock to internal (0) and that helped somewhat |
| 09:07.55 | frk2 | instead of the span going down 8-10 times an hour |
| 09:08.01 | frk2 | its not maybe like 3 times an hour |
| 09:08.04 | frk2 | now |
| 09:08.14 | Strom_M | first thing I'd try is looping the end of the cable and have the telco run a pattern loop test to make sure they're not getting any errors |
| 09:08.33 | Strom_M | do you have a loopback jack handy? |
| 09:08.36 | frk2 | done that |
| 09:08.39 | frk2 | they say its fine |
| 09:08.47 | frk2 | ive done the loop test on the card |
| 09:08.49 | frk2 | and the card is fine |
| 09:08.52 | Strom_M | you hard-looped the cable? |
| 09:08.57 | Strom_M | and you hard-looped the card? |
| 09:09.00 | frk2 | yes |
| 09:09.11 | frk2 | synced the card to itself |
| 09:09.12 | Strom_M | or did you flip a switch in software |
| 09:09.18 | frk2 | ran patlooptest |
| 09:09.22 | frk2 | and it timed out without errors |
| 09:09.46 | frk2 | no no |
| 09:09.48 | frk2 | hard cable |
| 09:09.51 | Strom_M | ok |
| 09:10.01 | frk2 | pins 1&3 and 2&4 i think need to be crossed |
| 09:10.12 | Strom_M | uh, no |
| 09:10.15 | frk2 | or something liek that.. but the cable was made properly |
| 09:10.24 | Strom_M | 1 -> 4 2 -> 5 |
| 09:10.37 | Strom_M | http://www.stromcarlson.com/wiring/T1-loopback.png |
| 09:10.42 | frk2 | yes- there u go |
| 09:10.49 | frk2 | haha used that URL only i think :) |
| 09:11.02 | Strom_M | heheh |
| 09:11.21 | frk2 | i even did intense debug |
| 09:11.41 | frk2 | the only thing it showed was something about like this: T200 timeout.. dont know what to do.. |
| 09:12.20 | Strom_M | you know, honestly, if all the CPE checks out correctly and the line checks out correctly, then maybe there's something wrong with the equipment on the other end of the circuit at the CO |
| 09:13.03 | Ritalin2 | the CO needs more cowbell |
| 09:13.08 | Strom_M | heh |
| 09:13.16 | frk2 | thats what im thinking |
| 09:13.28 | frk2 | take a look.. happened again... this time in full bloom |
| 09:13.30 | frk2 | http://pastebin.ca/315037 |
| 09:14.14 | Strom_M | have the telco switch their equipment around |
| 09:14.15 | frk2 | these HDLCs come in a blast |
| 09:14.51 | frk2 | for 25 minutes there are no errors.. then a whole big bunch and this happens |
| 09:15.11 | Strom_M | yeah....it's time to yell at the telco |
| 09:15.37 | frk2 | allright |
| 09:19.36 | frk2 | my telco dude suggested i try CAS signalling |
| 09:19.49 | frk2 | but then what do i use for the dchan? |
| 09:19.58 | Strom_M | um |
| 09:20.03 | Strom_M | is it a PRI, or is it not? |
| 09:20.06 | frk2 | just rawhdlc? |
| 09:20.09 | frk2 | it is a PRI |
| 09:20.17 | Strom_M | because if it's a PRI, CAS is pointless |
| 09:20.31 | Strom_M | find someone at the telco who actually knows a PRI from a hole in the ground |
| 09:20.44 | frk2 | thats hard.. its a third world country |
| 09:20.44 | frk2 | :) |
| 09:20.58 | frk2 | he also suggested to enable crc4 |
| 09:21.18 | Strom_M | give that a shot, as that's carried on channel 0 IIRC |
| 09:22.16 | frk2 | red alarm on the pri using crc4 |
| 09:22.21 | Strom_M | and put the timing source back at "telco" |
| 09:22.27 | frk2 | i just did that |
| 09:22.41 | frk2 | what does REC alarm mean? |
| 09:22.52 | Strom_M | do a sanity check and find out exactly how the PRI is supposed to be provisioned |
| 09:22.56 | frk2 | it continues to work with a REd alarm!!!!! |
| 09:23.01 | frk2 | what? |
| 09:23.05 | Strom_M | that's really bizarre |
| 09:23.15 | Strom_M | find out exactly what settings the telco has on their end |
| 09:23.38 | frk2 | CAS CRC4 they say |
| 09:23.47 | frk2 | which is obviously bullshit |
| 09:23.52 | frk2 | this is bizarree dude!!! |
| 09:24.13 | frk2 | what does a REC alarm mean in zap show status? |
| 09:24.58 | Strom_M | red alarm should mean "nothing" |
| 09:25.03 | Strom_M | well, maybe it isnt a PRI then; maybe it's a CAS E1 |
| 09:25.06 | frk2 | no it goes RED/REC |
| 09:25.14 | frk2 | then how does it work? |
| 09:25.42 | Strom_M | are you on the phone with the telco now? |
| 09:26.22 | frk2 | no - wasss |
| 09:27.07 | Strom_M | get back on the phone with them and ask someone else whether this is supposed to be CAS or whether it should be PRI |
| 09:28.59 | frk2 | but tell me |
| 09:29.11 | frk2 | if is was actually CAS- it wouldn't work with vioce would it? |
| 09:29.34 | frk2 | TMPASTSRV*CLI> zap show status |
| 09:29.34 | frk2 | Description Alarms IRQ bpviol CRC4 |
| 09:29.34 | frk2 | Digium Wildcard TE110P T1/E1 Card 0 REC 0 0 0 |
| 09:29.45 | frk2 | this stays.. but the card is working fine |
| 09:30.17 | Strom_M | cas is for voice too |
| 09:30.33 | Strom_M | REC is likely "receive" |
| 09:31.43 | *** join/#asterisk _mh (n=largo@202.5.145.13) |
| 09:32.12 | *** part/#asterisk _mh (n=largo@202.5.145.13) |
| 09:32.37 | frk2 | does trying cas with rawhdlc as the d-channel make any sense? |
| 09:32.45 | Strom_M | no |
| 09:32.53 | frk2 | :) |
| 09:33.17 | Strom_M | like i said - verify from the telco what the E1 is actually provisioned for |
| 09:33.27 | frk2 | CAS/CRC4 |
| 09:33.32 | frk2 | thats what they say |
| 09:33.55 | *** join/#asterisk CrashHD (n=crashhd@c-67-182-167-222.hsd1.ca.comcast.net) |
| 09:34.54 | Strom_M | well then it ain't a PRI |
| 09:35.34 | frk2 | but they call it a PRI |
| 09:35.42 | frk2 | so if i were to use cas |
| 09:36.10 | Strom_M | well then get a different telco, because this one doesnt know what its doing |
| 09:36.25 | frk2 | its called a state monopoly |
| 09:36.30 | frk2 | its the only telco |
| 09:36.37 | frk2 | whatever they say is right |
| 09:36.38 | frk2 | :) |
| 09:38.06 | *** join/#asterisk H2S04 (n=ghorthas@71-218-120-117.hlrn.qwest.net) |
| 09:38.25 | Strom_M | well, speak to someone higher up |
| 09:40.44 | frk2 | I know the CPE modem DEFINITELY shows CAS |
| 09:44.54 | *** join/#asterisk osas (n=nnnnnnnn@CABLE-72-53-75-244.cia.com) |
| 09:48.05 | frk2 | independent telco consultant is suggesting a modem issue |
| 09:48.27 | SwK | what kind of computer do you have that TE110 in? |
| 09:48.43 | SwK | as in is it a brand name like a dell or something? |
| 09:50.20 | *** join/#asterisk acehunky (n=chat_jok@203.124.217.98) |
| 09:50.33 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 09:50.33 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 09:50.52 | acehunky | hello anyone has exp with MFCR2 over asterisk ? |
| 10:04.17 | *** join/#asterisk reber (i=reber@gateway/tor/x-6c5a1077ef1556df) |
| 10:10.57 | *** join/#asterisk |dennis| (n=dennis@200.32.233.82) |
| 10:13.47 | *** join/#asterisk vgster (n=vgster@cpc2-ledn1-0-0-cust826.leed.cable.ntl.com) |
| 10:15.21 | *** join/#asterisk _Garry__ (n=gkg@wlan.insider.org) |
| 10:15.33 | _Garry__ | Hi * |
| 10:16.30 | *** join/#asterisk frenzy (n=frenzy@unaffiliated/frenzy) |
| 10:16.50 | frenzy | is digium site down? |
| 10:17.37 | *** join/#asterisk The_LightSide (n=dialt@wbs-41-208-200-5.wbs.co.za) |
| 10:17.48 | _Garry__ | got a problem with mISDN ... compiled fine, misdn-init start worked fine too, was able to use Asterisk with it too - anyway, after reboot, modules were loaded automatically, but some failed ... how can I keep it from loading during boot? I don't see any rc-script that loads it ... !? |
| 10:18.18 | _Garry__ | (on Debian that is) |
| 10:18.36 | The_LightSide | hi all, does any1 know if early media is supported on the single span E1/T1 card? |
| 10:19.38 | Strom_M | The_LightSide, it should be. |
| 10:19.50 | *** join/#asterisk mitcheloc (n=mitchelo@titaniumsoft.net) |
| 10:20.25 | The_LightSide | is there a chance that there is a bug in the latest zaptel that will cause it to not work? |
| 10:20.55 | Strom_M | are you having problems? |
| 10:21.01 | Strom_M | if so, describe your problem |
| 10:21.20 | The_LightSide | yeah... it seems from the sip side of things im getting inband progress tones |
| 10:21.28 | The_LightSide | but not when i dial out thru the isdn card |
| 10:22.03 | The_LightSide | i have priindication = inband in the zapata.con |
| 10:22.04 | The_LightSide | f |
| 10:22.21 | Strom_M | take the line out completely |
| 10:23.25 | The_LightSide | still gives me the indication tones specified in indications.conf |
| 10:23.50 | Strom_M | well, is the other side sending PROGRESS, or are they sending ALERTING? |
| 10:24.13 | Strom_M | because in ISDN, you're supposed to send progress messages and let the calling side generate its own indication tones |
| 10:24.17 | The_LightSide | if i remember correctly is worked with the dual span card |
| 10:24.27 | Strom_M | odd |
| 10:24.33 | Strom_M | which version of zaptel are you running? |
| 10:24.40 | The_LightSide | this single span card really is shit |
| 10:25.14 | The_LightSide | 1.2.12 |
| 10:26.38 | Strom_M | and on the sane circuit, a dual span card works fine? |
| 10:26.42 | Strom_M | s/sane/same/ |
| 10:27.00 | The_LightSide | and yes, im sending alerting |
| 10:27.06 | The_LightSide | yes |
| 10:27.27 | The_LightSide | also the single span only works with zaptel 1.2.11 up |
| 10:28.13 | Strom_M | wait, you're sending ALERTING? is this your own private ISDN circuit? |
| 10:28.19 | The_LightSide | yes |
| 10:28.24 | Strom_M | ah ok |
| 10:28.32 | Strom_M | which card specifically is this? |
| 10:29.02 | The_LightSide | my father designed the terminating unit... its the TE110p |
| 10:29.58 | Strom_M | that's odd |
| 10:30.28 | Strom_M | I've had no trouble working with those cards before |
| 10:30.57 | The_LightSide | ive had endles trouble |
| 10:31.15 | *** part/#asterisk frenzy (n=frenzy@unaffiliated/frenzy) |
| 10:31.57 | The_LightSide | dunno y tho |
| 10:32.18 | Strom_M | well, i've got a couple of TE110Ps here that I can lab up for you tomorrow - it's 2:32 AM here right now |
| 10:32.49 | The_LightSide | holy crap.. where are u? |
| 10:32.58 | Strom_M | los angeles |
| 10:33.02 | The_LightSide | ahh ok |
| 10:33.08 | Strom_M | where are you? cape town? |
| 10:33.19 | The_LightSide | Johannesburg |
| 10:33.25 | Strom_M | my second guess :) |
| 10:33.29 | The_LightSide | ;) |
| 10:33.38 | The_LightSide | midday here |
| 10:33.47 | The_LightSide | u up rather late, i must say |
| 10:33.49 | Strom_M | *nod* |
| 10:33.50 | Strom_M | yeah |
| 10:34.00 | Strom_M | i was up late last night and slept in this morning |
| 10:34.22 | The_LightSide | ahhh ok... i know about that... i spent 2 nights in a row trying to get this card working |
| 10:35.00 | Strom_M | you know, you /do/ get free install support from digium |
| 10:35.14 | The_LightSide | i do? how do i get that? |
| 10:35.42 | The_LightSide | specially as i went to the local supplier and it turns out i knew more than they did :( |
| 10:36.02 | Strom_M | call during business hours +1 256 428 6000 or IAX2/guest@misery.digium.com |
| 10:36.38 | The_LightSide | ahhh ok... ill do the IAX thing... its cheaper :) |
| 10:36.43 | Strom_M | :) |
| 10:37.06 | *** join/#asterisk Faithful (n=Faithful@ns.linuxterminal.com) |
| 10:37.24 | The_LightSide | im rather annoyed that the trixbox installs have gone to RPM |
| 10:38.28 | Strom_M | please dont tell me you use trixbox in production |
| 10:39.23 | The_LightSide | LOL... im doing this for my own office... i dont supply |
| 10:40.13 | Strom_M | even for your own office |
| 10:40.39 | The_LightSide | whats wrong with trixbox? |
| 10:40.45 | The_LightSide | its convenient |
| 10:41.35 | Strom_M | well, sure, if convenience is more important to you than security and stability |
| 10:41.44 | The_LightSide | all the extra features are just there... |
| 10:41.50 | Strom_M | and if you like giant creeping thing-like macros... |
| 10:42.08 | The_LightSide | its not on the net, so from that point its ok |
| 10:42.17 | The_LightSide | ok, sure the macros are a bit creepy |
| 10:42.55 | *** join/#asterisk osas (n=nnnnnnnn@CABLE-72-53-75-244.cia.com) |
| 10:43.00 | The_LightSide | and i do accept the stability issues |
| 10:44.21 | Strom_M | i'd say give the te110p a shot on vanilla asterisk on the linux distro of your choice - there may be some freakiness in trixbox that's causing your problem |
| 10:45.35 | The_LightSide | thing is tho... i downloaded the latest zaptel, libpri, asterisk, asterisk-addons and asterisk sounds and recompiled all of them |
| 10:45.47 | Strom_M | right, but its not the code; its the configurations |
| 10:45.59 | The_LightSide | ok... |
| 10:46.05 | Strom_M | trixbox configurations are notoriously full of shit |
| 10:46.36 | The_LightSide | the configs i should worry about are, zaptel, zapata and? |
| 10:47.04 | Strom_M | zaptel, zapata, and the dialplan |
| 10:47.20 | Strom_M | there are multiple ways to fuck up inband progress |
| 10:47.35 | The_LightSide | ok, those are more than vanilia |
| 10:48.16 | Strom_M | and i can tell you from personal experience that I have run that exact card on a circuit on regular old asterisk with perfect inband progress |
| 10:50.16 | The_LightSide | hmmm.. ok |
| 10:50.16 | The_LightSide | this is all i have in my zapata |
| 10:50.16 | The_LightSide | context=from-pstn |
| 10:50.16 | The_LightSide | switchtype=euroisdn |
| 10:50.16 | The_LightSide | signalling=pri_net |
| 10:50.17 | The_LightSide | pridialplan=unknown |
| 10:50.17 | The_LightSide | prilocaldialplan=unknown |
| 10:50.17 | The_LightSide | rxwink=300 |
| 10:50.17 | The_LightSide | group=0 |
| 10:50.17 | The_LightSide | channel => 1-8 |
| 10:50.17 | The_LightSide | immediate=yes |
| 10:50.27 | Strom_M | um |
| 10:50.31 | Strom_M | ~pb |
| 10:50.37 | jbot | i heard pb is a place to paste your stuff without flooding the channel - try http://pastebin.ca, or http://channels.debian.net/paste |
| 10:50.37 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 10:50.37 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 10:50.57 | The_LightSide | lol... i only thought of that afterwards |
| 10:50.59 | The_LightSide | sorry |
| 10:51.32 | Strom_M | now, of course, if you receive ALERTING, then according to ISDN spec, /you/ are responsible for generating progress indication |
| 10:52.09 | Strom_M | you're only supposed to play inband progress audio if you receive PROCEEDING |
| 10:52.37 | The_LightSide | hmmm |
| 10:52.49 | The_LightSide | and the whole early media thing? |
| 10:53.02 | Strom_M | that's what i'm talking about |
| 10:53.17 | Strom_M | "early media" is a VoIP term; i'm talking ISDN |
| 10:53.40 | The_LightSide | ok, the theory tho is the same? |
| 10:54.14 | The_LightSide | apprently the device does send proceeding and then alerting |
| 10:55.00 | Strom_M | what happens if you send proceeding followed by audio? |
| 10:55.20 | The_LightSide | ok, thats going to be a bit tricky to do |
| 10:56.41 | Strom_M | here's a better question - /why/ is it so important that you get your progress indication tones from the network instead of locally? |
| 10:57.33 | The_LightSide | cause some services here do not generate a answer condition, yet still provide audio |
| 10:58.00 | *** join/#asterisk oQPa (n=roque@15.Red-83-40-197.dynamicIP.rima-tde.net) |
| 10:58.24 | The_LightSide | and, it usually misses the first second of speach |
| 10:58.32 | Strom_M | do they generate a proceeding condition? |
| 10:58.54 | Strom_M | im getting tired |
| 10:58.58 | The_LightSide | not sure... havnt checked, we dont have any telkom lines anymore |
| 10:58.59 | Strom_M | do they send a proceeding message? |
| 10:59.04 | Strom_M | heh |
| 10:59.22 | The_LightSide | cable theft, 2 months to repair and still nothing |
| 10:59.30 | Strom_M | jesus |
| 10:59.30 | The_LightSide | we going celular now |
| 10:59.43 | Strom_M | vodacom? |
| 10:59.52 | The_LightSide | vodacom, mtn and cell c |
| 10:59.55 | *** join/#asterisk af_ (n=af@ip-170-44.sn1.eutelia.it) |
| 11:00.17 | Strom_M | ive got a vodacom SIM from 1994 around here somewhere |
| 11:00.25 | The_LightSide | 8 lines in total |
| 11:00.38 | The_LightSide | that has expired... im sure |
| 11:01.00 | The_LightSide | btw, u should go sleep ;) |
| 11:01.19 | Strom_M | it was never activated |
| 11:01.29 | Strom_M | yeah, i should |
| 11:01.47 | The_LightSide | hmmmm, the cards usually still have an expirey date tho |
| 11:03.31 | The_LightSide | lol, good night.. thanks for the help and info :) |
| 11:03.56 | Strom_M | oh, im not going yet |
| 11:04.04 | Strom_M | i said "i should" -- not "I am" |
| 11:05.03 | The_LightSide | damn, its now what? 3 am? |
| 11:05.42 | Strom_M | yeah |
| 11:05.51 | The_LightSide | i cant do that any more... and im still a youngster |
| 11:06.49 | Strom_M | how old? |
| 11:08.33 | The_LightSide | 25 |
| 11:08.52 | Strom_M | ah ok |
| 11:09.00 | Strom_M | i'm 24 |
| 11:09.11 | The_LightSide | lol.. just u wait ;p |
| 11:19.30 | *** join/#asterisk UlbabraB (n=salama@host241-43-static.72-81-b.business.telecomitalia.it) |
| 11:34.10 | *** join/#asterisk benoit35 (n=benoit@ebox.blorand.org) |
| 11:35.47 | *** join/#asterisk stimpie (n=michiel@ip565faf27.direct-adsl.nl) |
| 11:36.04 | benoit35 | hi everybody |
| 11:36.55 | monsted | hi, dr. nick! |
| 11:37.02 | benoit35 | i'm actually trying to install asterisk on lfs (linuxfromscratch) and i have no connection between client/server |
| 11:37.20 | benoit35 | nothing logged, how can i resolve this |
| 11:39.23 | *** join/#asterisk xheliox (n=jeff@pdpc/supporter/active/xheliox) |
| 11:50.15 | *** join/#asterisk acehunky (n=chat_jok@203.124.217.98) |
| 11:50.33 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 11:50.33 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 11:51.01 | *** join/#asterisk RoyK (n=roy@217-175-39.100710.adsl.tele2.no) |
| 11:57.54 | *** join/#asterisk Assid (i=assid@59.183.33.52) |
| 12:12.31 | *** join/#asterisk welby (n=welby@81.29.66.66) |
| 12:12.41 | *** join/#asterisk Lokiji (n=Lokiji@ip-89-102-178-195.karneval.cz) |
| 12:15.12 | *** join/#asterisk UlbabraB (n=salama@host241-43-static.72-81-b.business.telecomitalia.it) |
| 12:32.14 | *** join/#asterisk reber (i=reber@gateway/tor/x-307bdc40eceded52) |
| 12:48.02 | *** join/#asterisk coppice (n=chatzill@129.168.17.210.dyn.pacific.net.hk) |
| 12:50.33 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 12:50.33 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 13:03.15 | *** join/#asterisk Thazza (n=no@229.9.233.220.exetel.com.au) |
| 13:09.26 | *** join/#asterisk vgster (n=vgster@cpc2-ledn1-0-0-cust826.leed.cable.ntl.com) |
| 13:14.22 | *** join/#asterisk Bazy (n=bazy@eu.ii.dau.la.mata.capra.ro) |
| 13:21.35 | Dr-Linux|home | can you pass variables from dialplan to agi and agi to dialplan? |
| 13:33.07 | redax | sure |
| 13:33.31 | redax | use GET VARIABLE xx via AGI interface from the your script |
| 13:33.36 | redax | and SET VARIABLE ... |
| 13:33.57 | redax | or you can use AGI(somescrpt.agi|param1|param2) |
| 13:38.00 | *** part/#asterisk Bazy (n=bazy@eu.ii.dau.la.mata.capra.ro) |
| 13:39.52 | *** join/#asterisk _matt (n=matt@82-33-68-44.cable.ubr01.trow.blueyonder.co.uk) |
| 13:40.14 | _matt | hello, does anybody know if its possiable to make asterisk and a linksys PAP2 work with BT based caller ID idevices ? |
| 13:40.23 | _matt | BT being UK |
| 13:48.00 | acehunky | hello |
| 13:48.25 | acehunky | any one knows why i might be getting Double miss (223, 168) in my messages ? |
| 13:48.43 | *** join/#asterisk anonymouz666 (n=anonymou@200.218.193.6) |
| 13:48.45 | redax | _matt: checking my pap2 |
| 13:48.47 | acehunky | is steve underwod here |
| 13:48.48 | acehunky | ? |
| 13:49.04 | _matt | reber, cheers |
| 13:49.32 | _matt | reber, i have seen the caller id info appear from my asterisk box on the web interface of the linksys pap2 during a call |
| 13:49.42 | anonymouz666 | What does mean the jitter buffer on pap2 "up and down"? Jitter Buffer isn't only on incoming packets? |
| 13:49.51 | _matt | i just wondered if i could plug in one of those little caller id boxes :) |
| 13:50.13 | redax | _matt: which callerid method used in the UK? |
| 13:50.33 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 13:50.33 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 13:50.35 | _matt | reber, i dont know tbh i have only just started looking into it |
| 13:50.49 | redax | ETSI FSK With PR(UK) |
| 13:50.53 | redax | is that ok for you? |
| 13:51.22 | acehunky | hello _matt can ya help me to understand why i would be getting double miss in my var log message ? |
| 13:51.22 | _matt | http://www.ainslie.org.uk/callerid/cli_faq.htm#Q_6 |
| 13:51.25 | _matt | i have just been reading that |
| 13:51.49 | *** join/#asterisk robl^ (n=robl@dsl093-025-218.hou1.dsl.speakeasy.net) |
| 13:52.03 | _matt | "Remember, there is no such thing as "UK" Caller ID!!" |
| 13:52.05 | _matt | hummm |
| 13:52.48 | _matt | i guess i could just buy a box off ebay so if dosn't matter what methods it uses aslong as it can get info from the pap2 |
| 13:52.52 | acehunky | i believe that in UK to get callerId you need to have polarity reversal |
| 13:53.21 | _matt | acehunky, do you know if the pap2's support that ? |
| 13:53.27 | redax | you can specify 5-8 methods in pap2 |
| 13:53.38 | redax | for my cordless phone the ETSI works here |
| 13:53.38 | acehunky | umm pap2 does it anything to do with FXO port ? |
| 13:53.42 | redax | some panasonic |
| 13:53.47 | acehunky | i believe pap2 = FXS only |
| 13:54.01 | redax | pap2 has 2 FXS |
| 13:54.13 | _matt | acehunky, it is fxs only .. |
| 13:54.18 | redax | SPA-3000 1FXO/1FXS |
| 13:54.32 | _matt | acehunky, but i want to get caller id on my phone from my pap2 box |
| 13:55.06 | redax | _matt; try to change the Callerid method on the bottom of the Regional tab |
| 13:55.13 | redax | in the pap2 webinterface |
| 13:56.03 | _matt | reber, k, just taking a look |
| 13:56.03 | acehunky | umm pap2 box forwards callerID to asterisk over SIP |
| 13:56.50 | _matt | acehunky, nooo... if it was that way around my asterisk box would grenerate the caller id |
| 13:57.35 | _matt | but i dont bother about outbound caller id the service i use just appears as unavaliable |
| 13:58.56 | _matt | acehunky, i dont seem to have a caller id method :( |
| 13:59.05 | _matt | oh wait wasn't it advanced mode |
| 13:59.21 | _matt | ohhh yea :) |
| 13:59.33 | _matt | reber, cheers |
| 14:15.58 | *** join/#asterisk gr0mit_home (n=Tim@extrt.txrx.org.uk) |
| 14:17.09 | *** join/#asterisk Newbie___ (i=me@60.49.23.186) |
| 14:17.38 | Newbie___ | hi: has anyone got chanskype working with asterisk? |
| 14:18.43 | *** join/#asterisk eltech (i=G00Ds@ool-457c93b6.dyn.optonline.net) |
| 14:21.53 | *** join/#asterisk toxap (i=toxap@194.187.128.88) |
| 14:22.08 | *** join/#asterisk s1gny|wrk (n=s1gny@p54914E21.dip.t-dialin.net) |
| 14:22.27 | *** part/#asterisk s1gny|wrk (n=s1gny@p54914E21.dip.t-dialin.net) |
| 14:24.46 | *** join/#asterisk af_ (n=af@ip-170-44.sn1.eutelia.it) |
| 14:26.48 | *** join/#asterisk blitzrage (n=blitzrag@asterisk/documenteur-extraordinaire/blitzrage) |
| 14:27.26 | *** join/#asterisk backblue (n=moo@89-180-134-23.net.novis.pt) |
| 14:30.35 | *** join/#asterisk lorinc (n=ang@caracas-3441.adsl.interware.hu) |
| 14:32.51 | *** join/#asterisk PeppiX (n=PeppiX@85-18-66-24.ip.fastwebnet.it) |
| 14:32.55 | *** join/#asterisk Napoleao_ (n=napoleao@85.139.198.62) |
| 14:38.12 | *** join/#asterisk coppice (n=chatzill@129.168.17.210.dyn.pacific.net.hk) |
| 14:38.39 | *** join/#asterisk bkw_ (n=brian@ip68-0-120-100.tu.ok.cox.net) |
| 14:41.12 | *** join/#asterisk Igbothom_3rd (n=Hilton@office.quarkit.com.au) |
| 14:42.07 | *** join/#asterisk coppice (n=chatzill@129.168.17.210.dyn.pacific.net.hk) |
| 14:43.47 | tzanger | morning coppice |
| 14:44.01 | tzanger | I hear there are tsunami warnings in your part of the world, are you on high ground? |
| 14:44.09 | *** join/#asterisk Chicago (n=Chicago@c-67-186-94-7.hsd1.in.comcast.net) |
| 14:44.35 | coppice | if there's a tsunami disneyland gets it. we should be able to watch :-) |
| 14:45.15 | tzanger | ha |
| 14:45.23 | tzanger | how are things? I haven't seen you on in a while |
| 14:45.32 | tzanger | mind you I've been AWOL for a while myself |
| 14:45.48 | tzanger | busy trying to get openslug compiled so I can get raid support in the damned kernel |
| 14:46.03 | *** join/#asterisk vgster (n=vgster@cpc2-ledn1-0-0-cust826.leed.cable.ntl.com) |
| 14:46.12 | Chicago | Where is a good asterisk installation howto for BSD? I'm on openbsd and looking for the proper way to startup asterisk in my rc.local |
| 14:48.03 | blitzrage | tzanger: yo |
| 14:48.15 | tzanger | yo |
| 14:48.42 | blitzrage | I need water, tea, and vitamins.... stat |
| 14:50.33 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 14:50.33 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 14:50.35 | tzanger | water, tea and vitamins? |
| 14:50.37 | tzanger | where are you? |
| 14:51.30 | blitzrage | at home |
| 14:52.02 | blitzrage | for some reason I'm hung over.... and I didn't even drink that much last night |
| 14:52.28 | tzanger | describe "that much" :-) |
| 14:52.34 | tzanger | did someone slip you roofies |
| 14:53.14 | Chicago | Anybody wanna help me get going on openbsd? |
| 14:54.19 | tzanger | Chicago: I don't do bsd |
| 14:54.20 | tzanger | sorry |
| 14:54.27 | *** join/#asterisk coppice (n=chatzill@129.168.17.210.dyn.pacific.net.hk) |
| 14:54.29 | blitzrage | tzanger: don't think so... was just at a buddies house last night |
| 14:54.33 | tzanger | hmm |
| 14:54.49 | blitzrage | although I had some crazy guy ask me to go smoke opium with him when I was getting off the bus |
| 14:54.59 | tzanger | hahaha |
| 14:55.02 | blitzrage | but I didn't go smoke the opium... so that couldn't have been it :) |
| 14:55.08 | tzanger | and the next thing you remember was waking up in an opium den |
| 14:55.11 | blitzrage | lol |
| 14:55.34 | blitzrage | nada BSD here... Linux |
| 14:56.02 | Chicago | well, hopefully somebody will come along =) |
| 14:56.12 | blitzrage | ideally :) |
| 14:56.18 | RazaMetaL | hi |
| 14:56.23 | blitzrage | don't you just call safe_asterisk? |
| 14:56.29 | tzanger | ok openslug has xfs modules now, but I can't get raid support in |
| 14:56.29 | tzanger | wtf |
| 14:56.32 | tzanger | I just can't iwn |
| 14:56.45 | RazaMetaL | is possible to send html e-mail messages from voicemail.conf file ? |
| 14:57.07 | blitzrage | sure... just add HTML code to the msg you're sending |
| 14:57.11 | tzanger | haha nope the fucking module was stripped |
| 14:57.12 | tzanger | idiots |
| 14:57.18 | RazaMetaL | blitzrage, thank you |
| 14:57.30 | tzanger | blitzrage: is it that simple? Don't you need to send a mime-multipart message instead of straight text? |
| 14:57.31 | blitzrage | RazaMetaL: see... that kind of stuff you should just try :) |
| 14:57.39 | tzanger | mind you it's attaching the voicemail so it's already mulitpart |
| 14:57.43 | tzanger | but you won't have html and txt versions |
| 14:57.50 | blitzrage | it's entirely possible you're right |
| 14:58.02 | blitzrage | I'd just say giv'r a shot :) |
| 14:58.08 | RazaMetaL | tzafrir, ok.. thankz |
| 14:58.23 | blitzrage | too many people with names that start with 'tz' here |
| 14:58.23 | tzanger | oh yes definitely try it |
| 14:58.26 | tzanger | you cna't break anything |
| 14:58.39 | tzanger | blitzrage: I am one of hte originals, my nick's back from the early 90s with efnet |
| 14:58.41 | blitzrage | except the space-time continuum |
| 14:58.48 | tzanger | and slackware :-) I didn't start out on SLS but close :-) |
| 14:59.08 | blitzrage | oooo... look at mister la dee da |
| 14:59.28 | tzanger | blitzrage: you're just pissed that at that point in time you were in diapers yet |
| 14:59.43 | tzanger | but who I am i kidding, you still wear them for that strange role-playing stuff you do |
| 14:59.53 | coppice | I started out entering programs in binary on rows of front panel switches. |
| 15:00.00 | blitzrage | lol... I got nothing for that |
| 15:00.18 | tzanger | coppice: yes you've beat me there |
| 15:00.23 | blitzrage | ummm... I used a commodore 64 when I was in grade 2... :) |
| 15:03.36 | Chicago | Well... there are sample scripts for debian,gentoo,mandrake,redhat and slackware... but not bsd. |
| 15:05.11 | tzanger | yeah I had a commodore |
| 15:05.13 | tzanger | still do actually |
| 15:06.50 | coppice | commodore 64? luxury |
| 15:07.09 | tzanger | cool the raid array's up |
| 15:07.52 | tzanger | now I still need to get xfs working but at least the array's not dead |
| 15:07.58 | tzanger | it seems to be stuck on ARMeb though |
| 15:12.10 | Corydon76-home | coppice: closest I've come to that is hand assembling my assembly instructions, then entering them with Apple's mini-assembler |
| 15:12.28 | *** join/#asterisk SomeOne1 (n=SomeOne1@pool-71-126-150-34.washdc.fios.verizon.net) |
| 15:12.30 | SomeOne1 | exten => s,n,Set(limit_miliseconds=$[${total_seconds_remaining} <= 3600]?${Math(${total_seconds_remaining}*1000,int)}:3600000) |
| 15:12.33 | SomeOne1 | why doesnt that work? |
| 15:12.51 | SomeOne1 | you cant do conditions in Set like that? |
| 15:12.54 | SomeOne1 | is there any other way? |
| 15:12.58 | SomeOne1 | to like return one thing or the other |
| 15:13.31 | Corydon76-home | Use the ${IF(cond?true:false)} construct |
| 15:13.37 | SomeOne1 | man |
| 15:13.42 | SomeOne1 | where the hell did you find that dude |
| 15:13.48 | SomeOne1 | i couldnt see it on the wiki ANYWHERE |
| 15:13.56 | SomeOne1 | thanks :) |
| 15:13.58 | Corydon76-home | 'show functions' |
| 15:14.03 | Corydon76-home | 'show function IF' |
| 15:14.08 | SomeOne1 | ahh, its a "function" not a "command" |
| 15:14.09 | SomeOne1 | i see |
| 15:14.21 | Corydon76-home | You embed it in the Set |
| 15:14.27 | SomeOne1 | gotcha |
| 15:15.02 | SomeOne1 | exten => s,n,Set(limit_miliseconds=${IF($[${total_seconds_remaining} <= 3600]?${Math(${total_seconds_remaining}*1000,int)}:3600000)} |
| 15:15.06 | SomeOne1 | like that basically |
| 15:15.13 | *** join/#asterisk thoughtpolice (n=austin@ip70-185-140-61.lu.dl.cox.net) |
| 15:15.18 | Corydon76-home | Missing a closing ')' but yet |
| 15:15.22 | Corydon76-home | yes |
| 15:15.48 | SomeOne1 | exten => s,n,Set(limit_miliseconds=${IF($[${total_seconds_remaining} <= 3600]?${Math(${total_seconds_remaining}*1000,int)}:3600000))} |
| 15:15.56 | *** join/#asterisk Nukemizer (n=Nuke@160.7.249.15) |
| 15:16.02 | Corydon76-home | Reverse the last two characters on that |
| 15:16.28 | SomeOne1 | err, oops |
| 15:16.42 | Corydon76-home | Also, MATH() is case-sensitive |
| 15:16.56 | Corydon76-home | All functions are all-caps |
| 15:17.04 | SomeOne1 | Jan 13 10:16:59 ERROR[15479]: pbx.c:1382 ast_func_read: Function Math not registered |
| 15:17.13 | SomeOne1 | is that why its saying that? |
| 15:17.16 | Corydon76-home | Yes |
| 15:17.20 | SomeOne1 | gothca |
| 15:17.23 | *** join/#asterisk trumee (n=trumee@cpc2-cmbg10-0-0-cust1015.cmbg.cable.ntl.com) |
| 15:17.28 | SomeOne1 | i <3 Corydon76-home |
| 15:17.41 | Corydon76-home | Technically, you don't need the MATH function at all in there, you could get by with $[] |
| 15:18.30 | trumee | guys, i am trying to setup google talk with asterisk 1.4. The jabber client seems to be connected since "jabber show connected" shows that. However, in googletalk the user is showing up as offline |
| 15:18.38 | *** join/#asterisk hohum (n=dcorbe@c-71-62-76-68.hsd1.va.comcast.net) |
| 15:18.53 | Dr-Linux|home | can you pass variables from dialplan to agi and agi to dialplan? |
| 15:19.15 | trumee | anybody here has experience hooking asterisk to googletalk? |
| 15:19.17 | Corydon76-home | Dr-Linux|home: GET VARIABLE and SET VARIABLE |
| 15:19.18 | robl^ | has anyone noticed that 1.4 starts using more and more CPU the longer it runs? |
| 15:19.34 | SomeOne1 | wait |
| 15:19.36 | SomeOne1 | i can do like |
| 15:19.52 | SomeOne1 | $[${total_seconds_remaining}*1000] ? |
| 15:19.56 | SomeOne1 | withouth the MATH |
| 15:19.57 | Corydon76-home | Yes |
| 15:20.01 | SomeOne1 | man |
| 15:20.06 | SomeOne1 | would that be faster? |
| 15:20.11 | SomeOne1 | i mean, in a production system |
| 15:20.21 | SomeOne1 | where everything counts greatly |
| 15:20.26 | Corydon76-home | Insignificantly so, but yes |
| 15:20.39 | SomeOne1 | Corydon76-home: do you have a programming background? |
| 15:20.50 | Corydon76-home | ROFL |
| 15:21.06 | SomeOne1 | heh |
| 15:21.11 | SomeOne1 | what about stuff like |
| 15:21.16 | SomeOne1 | <PROTECTED> |
| 15:21.20 | SomeOne1 | would that return integers? |
| 15:21.24 | Corydon76-home | Yes |
| 15:21.25 | SomeOne1 | ahhh, jack pot! |
| 15:21.29 | SomeOne1 | i need to download your brain |
| 15:21.30 | Dr-Linux|home | Corydon-w: and do you have an idea, why i can't transfer the call agi() ? while i can tranfser everywhere in the dialplan |
| 15:21.37 | Corydon76-home | Please read doc/README.variables |
| 15:21.50 | SomeOne1 | Corydon76-home: please give me your brain. |
| 15:22.00 | SomeOne1 | or i'll have to take it by force |
| 15:22.11 | Corydon76-home | Dr-Linux|home: eh? |
| 15:22.14 | SomeOne1 | im giving you the option to do this the easy way |
| 15:22.18 | *** join/#asterisk Ebola (n=Ebola@host81-152-204-157.range81-152.btcentralplus.com) |
| 15:22.54 | Dr-Linux|home | Corydon76-home: yeah, i'm fixing this issue far 3 weeks, but nothing seems to work |
| 15:23.44 | *** join/#asterisk oQPa (n=roque@15.Red-83-40-197.dynamicIP.rima-tde.net) |
| 15:24.04 | SomeOne1 | Corydon76-home: i've noticed one thing though... |
| 15:24.19 | SomeOne1 | MySQL() is inefficient in a way |
| 15:24.21 | SomeOne1 | but |
| 15:24.26 | SomeOne1 | RealTime() is like limited |
| 15:24.31 | SomeOne1 | for example |
| 15:24.34 | Corydon76-home | Using 1.2? |
| 15:24.51 | SomeOne1 | exten => 11223344,1,RealTime(sipusers|name|12023243260|var_) |
| 15:24.58 | SomeOne1 | you cant have multiple conditions in tehre |
| 15:25.00 | Corydon76-home | SomeOne1: using 1.2? |
| 15:25.03 | SomeOne1 | yeah |
| 15:25.05 | SomeOne1 | 1.2.13 |
| 15:25.18 | Corydon76-home | http://svncommunity.digium.com/view/func_odbc/1.2/ |
| 15:25.48 | Corydon76-home | Or just: svn co http://svncommunity.digium.com/svn/func_odbc/1.2 func_odbc |
| 15:25.52 | SomeOne1 | like that basically equals like select * from <table defined by "sipusers" realtime family> where name=1202blah |
| 15:25.58 | SomeOne1 | you cant have more conditions on where |
| 15:26.04 | SomeOne1 | okay |
| 15:26.21 | Corydon76-home | Also, see http://www.asterisk.org/func_odbc |
| 15:26.46 | SomeOne1 | would that be more efficient than using MYSQL()? |
| 15:27.13 | Dr-Linux|home | Corydon76-home: no clue for my queuestion? |
| 15:27.16 | SomeOne1 | also ODBC wouldnt be speaking to mysql in its native language so that might lead to more inefficiencies? |
| 15:27.19 | Corydon76-home | I don't know about more efficient, but there's fewer leaks and it is supported now in the core |
| 15:27.36 | SomeOne1 | err, not speaking in* |
| 15:28.11 | SomeOne1 | by leaks you mean that you dont have to store the password and login info for mysql in extensions.conf |
| 15:28.16 | SomeOne1 | or your extensions realtime family |
| 15:28.58 | Corydon76-home | By leaks, I mean that result sets that aren't immediately deallocated could remain in memory until a restart |
| 15:29.07 | SomeOne1 | hhh |
| 15:29.08 | SomeOne1 | ahhh |
| 15:29.11 | SomeOne1 | ive been worried about that |
| 15:29.24 | SomeOne1 | but im trying to get that covered in my dialplan in all possible cases |
| 15:29.25 | *** join/#asterisk EmleyMoor (i=ejabberd@hallam.tinsleyviaduct.com) |
| 15:29.28 | Corydon76-home | A hangup by the caller could make Mysql() results leak |
| 15:29.32 | SomeOne1 | hmm, i might just switch to this |
| 15:29.41 | SomeOne1 | well, im catching it in the 'h' extension |
| 15:29.58 | SomeOne1 | and doing exten => h,n(CONTINUE),MYSQL(Disconnect ${connid}) |
| 15:29.59 | Corydon76-home | The only major difference is that func_odbc is single-record result oriented |
| 15:30.04 | SomeOne1 | err, and the other thing |
| 15:30.06 | SomeOne1 | Clear |
| 15:30.28 | SomeOne1 | hmm |
| 15:30.33 | SomeOne1 | youre right this might seem like a smarter way |
| 15:30.42 | SomeOne1 | im so deep in using mysql in my dialplan now |
| 15:30.45 | SomeOne1 | i'll have to change a lot :( |
| 15:30.53 | EmleyMoor | If I Goto (or GotoIfTime in this case) to the s extension of another context, do the digits dialed remain available in ${EXTEN}? |
| 15:31.05 | Corydon76-home | EmleyMoor: No |
| 15:31.23 | SomeOne1 | man this sucks |
| 15:31.26 | SomeOne1 | why didnt i see this earlier |
| 15:31.37 | Corydon76-home | EmleyMoor: but you can do Goto(othercontext|${EXTEN}|1) |
| 15:31.55 | EmleyMoor | Ah, and will that pattern-match? |
| 15:32.00 | Corydon76-home | Yes |
| 15:32.05 | EmleyMoor | :-) |
| 15:32.24 | EmleyMoor | I am trying to make my "dial a mobile the cheapest way" bit a bit neater |
| 15:32.56 | SomeOne1 | Corydon76-home: wait, is the ODBC driver an addon? |
| 15:33.13 | Corydon76-home | SomeOne1: eh? |
| 15:33.25 | Corydon76-home | func_odbc is in the core as of 1.2 |
| 15:33.29 | Corydon76-home | err, 1.4 |
| 15:33.48 | Corydon76-home | 1.2 just has a backport |
| 15:33.51 | SomeOne1 | well the website said its been backported to 1.2 |
| 15:33.51 | SomeOne1 | yeah |
| 15:34.01 | SomeOne1 | is 1.4 still experimental? |
| 15:34.08 | SomeOne1 | im thinking of switching |
| 15:34.15 | tzanger | 90Mb/sec... that's USB2 I think |
| 15:34.17 | SomeOne1 | but im in a production-type environment |
| 15:34.21 | tzanger | I think USB1 is 12Mb/sec... or is it bytes |
| 15:35.48 | SomeOne1 | Corydon76-home: just real quickly, you think its worth my time to install unixODBC and set it all up that way or is MYSQL() just fine too? |
| 15:36.09 | SomeOne1 | basically func_odbc vs. MYSQL() |
| 15:36.15 | Corydon76-home | I don't have an answer for you |
| 15:36.23 | SomeOne1 | why so |
| 15:36.27 | SomeOne1 | heh |
| 15:36.27 | anonymouz666 | when you use ASTDB where the data are stored? |
| 15:36.28 | SomeOne1 | n/m |
| 15:36.33 | Corydon76-home | because that's up to you |
| 15:36.44 | SomeOne1 | dude im talking about efficicnecy |
| 15:36.53 | Corydon76-home | anonymouz666: /var/lib/asterisk/astdb |
| 15:37.06 | SomeOne1 | and who knows, MYSQL() might become obsolete soon and the asterisk community might get rid of it |
| 15:37.26 | Corydon76-home | Mysql() hasn't been updated in forever |
| 15:38.45 | anonymouz666 | mysql() and app_mysql() are the same? |
| 15:38.47 | Corydon76-home | And there is more than one kind of efficiency... Execution, development time, support itme |
| 15:38.59 | Corydon76-home | anonymouz666: correct |
| 15:39.34 | *** join/#asterisk DaveCanoe (n=Dave@209.167.5.2) |
| 15:40.27 | trumee | ah! now google talk can see my asterisk server. But when i place a call from google talk it gives this error http://pastebin.com/858411 |
| 15:43.22 | *** join/#asterisk dhill (i=dhill@fog.mindcry.org) |
| 15:43.49 | *** join/#asterisk The_LightSide (n=dialt@wbs-41-208-205-17.wbs.co.za) |
| 15:43.53 | blitzrage | did someone say func_odbc? |
| 15:44.07 | blitzrage | my odbc senses are tingling |
| 15:44.16 | dhill | I need to send 5 DID lines over an IAX tunnel to a customer. Should I allow the customer to set Caller ID? |
| 15:44.47 | blitzrage | are you terminating to the PSTN? if not, then it probably doesn't matter. I generally don't allow my customers to set CID |
| 15:44.57 | tzanger | dhill: I am of the position that CID should be allowed to be set until it's misused |
| 15:45.11 | tzanger | if you're paranoid just enforce that CID is only able to be set to one of his DIDs. |
| 15:45.40 | *** join/#asterisk wunderkin (i=kev@ip72-208-3-221.ph.ph.cox.net) |
| 15:46.18 | Corydon76-home | blitzrage: SomeOne1 asked if I had a programming background. |
| 15:46.37 | dhill | well, say i have an IAX connection called (iax-customer) and they have to me (iax-provider). They want their DID's to show up on callerid, not the main number.. so how do I know what number they are dialing from? |
| 15:47.01 | dhill | or do i need IAX for each DID if they want that? |
| 15:47.04 | *** join/#asterisk L|NUX (n=linux@unaffiliated/lnux/x-10290) |
| 15:47.17 | blitzrage | Corydon76-home: lol |
| 15:47.56 | blitzrage | dhill: multiple accounts... or, in that case, I typically allow the end point to set their CID |
| 15:48.31 | dhill | ever use an adtran 900 series? :) |
| 15:48.53 | tzanger | Corydon76-home: so do you? :-) |
| 15:49.04 | Corydon76-home | Not a bit. ;-) |
| 15:49.58 | SomeOne1 | Corydon76-home: i dont understand when you say "customers" |
| 15:50.02 | SomeOne1 | asterisk has customers? |
| 15:50.14 | Corydon76-home | No, the company I work for has customers |
| 15:50.24 | SomeOne1 | ahhh |
| 15:50.33 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 15:50.33 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 15:50.34 | SomeOne1 | i like having predefined queries with func_odbc |
| 15:50.38 | dhill | i was told asterisk is not "carrier grade" |
| 15:50.42 | SomeOne1 | has efficiency written all over it |
| 15:51.01 | SomeOne1 | as opposed to when you send in queries coded through the DIALPLAN |
| 15:51.05 | SomeOne1 | using MYSQL |
| 15:51.26 | Corydon76-home | Well, it's a classic case of overengineering the solution, and making a general purpose tool in the process |
| 15:51.27 | SomeOne1 | dhill: whoever told you, beat them with a spatula |
| 15:51.47 | SomeOne1 | heh |
| 15:51.53 | SomeOne1 | f*** it im just gonna use MYSQL |
| 15:51.54 | SomeOne1 | () |
| 15:52.05 | Corydon76-home | dhill: A class-5 switch isn't necessarily carrier-grade either |
| 15:52.23 | SomeOne1 | and make sure to MYSQL(Clear) or MYSQL(Disconnect) in the hangup extensions |
| 15:52.33 | SomeOne1 | Corydon76-home: thanks for your help man, take care |
| 15:52.38 | tzanger | you want func_odbc |
| 15:52.43 | tzanger | it's full of ODBC goodness |
| 15:52.45 | Corydon76-home | That works, as long as you're only querying Mysql |
| 15:52.53 | Corydon76-home | What if you wanted to query Oracle? |
| 15:52.56 | SomeOne1 | hmmm... |
| 15:52.59 | SomeOne1 | later it might be oracle |
| 15:53.00 | Nugget | ewwww, mysql. |
| 15:53.09 | SomeOne1 | no no no, Corydon76-home: this isnt work related |
| 15:53.09 | blitzrage | ewww indeed. pgsql goodness. |
| 15:53.13 | Corydon76-home | or DB2 or Postgres... |
| 15:53.18 | SomeOne1 | i.e. what i told you about where I work |
| 15:53.25 | Corydon76-home | Ah... |
| 15:53.26 | SomeOne1 | this is a private/personal project |
| 15:53.36 | Corydon76-home | That would be a kickass deployment, though |
| 15:53.38 | SomeOne1 | but youre right, i might want to switch to anohter DB later |
| 15:53.38 | tzanger | SomeOne1: so? I use postgres for all my private/personal projects |
| 15:53.40 | blitzrage | func_odbc just kicks ass... no reason to use anything else |
| 15:53.46 | tzanger | agreed |
| 15:53.51 | EmleyMoor | Wow! That's a lot better |
| 15:54.08 | SomeOne1 | blitzrage: does ODBC allow using a socket? |
| 15:54.14 | dhill | i think i will not allow customers to set callerid.. since it could cause issues with E911 |
| 15:54.14 | SomeOne1 | instead of tcp/ip |
| 15:54.21 | Corydon76-home | SomeOne1: yes, it does |
| 15:54.22 | SomeOne1 | if it does then im all for it |
| 15:54.29 | Corydon76-home | It's set up in /etc/odbc.ini |
| 15:54.44 | blitzrage | dhill: when someone dials E911, just force it then |
| 15:54.49 | blitzrage | you don't have to force it all the time |
| 15:54.53 | SomeOne1 | because my understanding is MYSQL() in asterisk is using tcp/ip, which even though its for "localhost" in my case, its got its overhead |
| 15:54.56 | SomeOne1 | more so than using a socket |
| 15:55.03 | Corydon76-home | It's a little more involved to set up ODBC, but it is much more versatile |
| 15:55.14 | SomeOne1 | eh, thats no problem |
| 15:55.19 | SomeOne1 | im just trying to save time for now |
| 15:55.25 | SomeOne1 | but it might be more benificial to use ODBC |
| 15:55.30 | SomeOne1 | i like the predefined queries too |
| 15:55.34 | *** join/#asterisk UlbabraB (n=salama@host241-43-static.72-81-b.business.telecomitalia.it) |
| 15:55.41 | TheAsp | <PROTECTED> |
| 15:55.42 | Corydon76-home | execution time, development time, or support time? |
| 15:55.43 | SomeOne1 | and using a socket |
| 15:55.53 | SomeOne1 | development time |
| 15:56.01 | SomeOne1 | and of couse, im concerned with execution/support time |
| 15:56.02 | Nugget | technically, tcp/ip is "a socket" too. |
| 15:56.10 | SomeOne1 | to localhost |
| 15:56.16 | SomeOne1 | doesnt it have headers and stuff? |
| 15:56.17 | SomeOne1 | still |
| 15:56.20 | SomeOne1 | tcp/ip |
| 15:56.22 | SomeOne1 | more overhead... |
| 15:57.18 | SomeOne1 | in a production system, in other cases it might be completely negligible |
| 15:57.18 | tzanger | SomeOne1: for a personal project you're worrying an awful lot about details that you'll never ever notice |
| 15:57.18 | Nugget | I'm just criticizing your terminology, not your decisionmaking. :) |
| 15:57.18 | SomeOne1 | heh |
| 15:57.18 | SomeOne1 | Nugget: gotcha |
| 15:57.18 | SomeOne1 | i meant file-socket |
| 15:57.29 | SomeOne1 | tzanger: well, its non-work related but like, its a personal project i'll be making money off |
| 15:57.37 | SomeOne1 | i.e. my career is different |
| 15:57.40 | SomeOne1 | this is an aside thing |
| 15:57.55 | tzanger | SomeOne1: again, if you're worrying about TCP/IP overhead you're already sunk. |
| 15:58.02 | SomeOne1 | heh |
| 15:58.16 | tzanger | because if you're not worrying then about your table names and column names being minimal, you're just pissing into the wind |
| 15:58.25 | Nugget | heh |
| 15:58.41 | SomeOne1 | regardless, you said <blitzrage> func_odbc just kicks ass... no reason to use anything else |
| 15:58.45 | TheAsp | SomeOne1: what makes you think mysql is going over tcp/ip anyway? |
| 15:58.46 | Nugget | use stored procedures to minimize the impact of element names. |
| 15:58.47 | SomeOne1 | so im in favor of that |
| 15:59.08 | SomeOne1 | TheAsp: well in asterisk's RealTime() you can provide a socket for MySQL |
| 15:59.15 | SomeOne1 | but the MYSQL() function, which is different |
| 15:59.22 | SomeOne1 | requires a "hostname" a "username |
| 15:59.24 | tzanger | SomeOne1: there isn't any reason to use something else for almost every implementation |
| 15:59.25 | SomeOne1 | " and password |
| 15:59.31 | blitzrage | hey, I'm using func_odbc for a clustered solution, and it works great |
| 15:59.39 | TheAsp | SomeOne1: libmysql should use the socket if you say localhost |
| 15:59.41 | blitzrage | ymmv, but thus far, its been rock solid |
| 15:59.43 | SomeOne1 | b;ah |
| 15:59.44 | tzanger | SomeOne1: if you want to use some DB-specific extension that is not supported by the ODBC driver you need to slap yourself with a standards book and think about it again |
| 15:59.59 | SomeOne1 | TheAsp: see i didnt know that, thanks for clarifying |
| 16:00.01 | tzanger | SomeOne1: and if the ODBC driver performance is killing you you either need to determine what's the reason behind that, or upgrade your hardware |
| 16:00.13 | TheAsp | SomeOne1: but you could disable tcp/ip in mysql and try it |
| 16:00.22 | tzanger | the only reason ODBC sucks is if the lowlevel driver is slow |
| 16:00.26 | blitzrage | tzanger: some people like to over-engineer stuff :) |
| 16:00.35 | tzanger | blitzrage: as an engineer, I know. :-) |
| 16:00.47 | SomeOne1 | heh |
| 16:00.51 | SomeOne1 | im an engineer too |
| 16:01.06 | SomeOne1 | you know what, in reality, im getting all worked up over nothing |
| 16:01.09 | SomeOne1 | just like you guys said |
| 16:01.18 | tzanger | SomeOne1: yep... engineers love to do that |
| 16:01.24 | *** join/#asterisk _Garry__ (n=gkg@wlan.insider.org) |
| 16:01.26 | SomeOne1 | it wont be handeling like a hundred thousand calls concurrently anyway |
| 16:01.34 | tzanger | I used to hate ODBC for the same reason... speed, but that's just not an issue for 99% of implementations |
| 16:01.56 | SomeOne1 | well, im off |
| 16:02.01 | SomeOne1 | good conversation |
| 16:02.03 | _Garry__ | could use some hints w/ mISDN on Debian ... |
| 16:02.11 | SomeOne1 | later guys |
| 16:03.03 | _Garry__ | misdn compiled fine, misdn-init start worked fine too, was able to use Asterisk with it too - anyway, after reboot, modules were loaded automatically, but some failed ... how can I keep it from loading during boot? I don't see any rc-script that loads it ... !? |
| 16:05.39 | *** join/#asterisk adorah (n=Michael@87.69.57.228.cable.012.net.il) |
| 16:07.09 | *** join/#asterisk kristalino (i=reber@gateway/tor/x-3089915d027e38fa) |
| 16:13.01 | *** join/#asterisk mitcheloc (n=mitchelo@titaniumsoft.net) |
| 16:13.29 | *** join/#asterisk airjump (n=MZ@p508AF023.dip.t-dialin.net) |
| 16:15.58 | *** part/#asterisk _Garry__ (n=gkg@wlan.insider.org) |
| 16:18.13 | *** join/#asterisk kFuQ (n=somedude@c-67-185-123-34.hsd1.wa.comcast.net) |
| 16:19.04 | redax | how can I get the UNIQUEID via the manager interface for a channel? |
| 16:19.22 | rene- | redax: it should be on the fields |
| 16:20.32 | *** join/#asterisk ManxPower (n=manxpowe@175.sub-75-202-155.myvzw.com) |
| 16:21.50 | redax | Action: GetVar |
| 16:22.07 | redax | Channel: xxxx |
| 16:22.13 | redax | variable_office: UNIQUEID |
| 16:22.16 | redax | grr. |
| 16:22.26 | redax | <PROTECTED> |
| 16:22.33 | redax | ]this is not working :? |
| 16:23.13 | rene- | mmm |
| 16:23.21 | rene- | i think that when the channel changes state |
| 16:23.25 | rene- | you can see the unique id |
| 16:23.32 | rene- | i have never done the way you intend |
| 16:23.49 | rene- | but it should work |
| 16:23.56 | rene- | maybe try __UNIQUEID |
| 16:23.59 | rene- | but i am not sure |
| 16:24.04 | ManxPower | I don't know if you can get system created variables that way. In the past you could not in AGI, but that was fixed. |
| 16:24.35 | ManxPower | redax: does it work if you set a variable in [globals]? Can you read it via manager"? |
| 16:24.46 | redax | yeah. that works |
| 16:24.49 | rene- | hello i have this scenario PSTN----[opener queue (dynamic local channel sip members)]----[closer queue or extension] i am having the openers transfer by means of # but opener stays on the path and therefore cant take any more calls the queue has a 't', transfers are enabled on the zapata conf and the dial in the local channel has a t also... i have canreinvite=yes and the queue does recording, is there a way the middle man can get out of |
| 16:25.07 | rene- | redax: why dont you set the variable in the dialplan |
| 16:25.26 | rene- | and read it over manager? |
| 16:25.50 | ManxPower | rene-: I believe there was a bug with regards to queues and transfers where your calllimit would not be decrimented on transfer. see the mailing list archives or the bug tracker. |
| 16:25.58 | ManxPower | the bug was fixed, IIRC |
| 16:26.19 | redax | ah |
| 16:26.32 | rene- | ManxPower: i am using branch and trunk (1.4) and i am experiencing this |
| 16:26.38 | redax | good idea :) |
| 16:26.55 | rene- | :) |
| 16:27.07 | rene- | i found an old post by mark saying that reinvite should be no |
| 16:27.11 | rene- | but this is circa 2002 |
| 16:27.26 | redax | another question is for Queue: I dont have TRANSFER events in queue_log, even if I really transfer a call to someone other |
| 16:33.32 | *** part/#asterisk oQPa (n=roque@15.Red-83-40-197.dynamicIP.rima-tde.net) |
| 16:33.39 | *** join/#asterisk oQPa (n=roque@15.Red-83-40-197.dynamicIP.rima-tde.net) |
| 16:34.21 | SomeOne1 | can you have multiple conditions in any of the IF statements |
| 16:34.53 | SomeOne1 | i.e. IF($[blah = blah || blah != blah2]) |
| 16:37.46 | *** join/#asterisk dhill (i=dhill@fog.mindcry.org) |
| 16:38.06 | dhill | sorry for the many questions |
| 16:38.27 | dhill | is it safe _not_ to register/authenticate sip users who have a static IP? |
| 16:39.37 | dhill | a friend does not use secret= or username= .. but just host=ip.add.re.ss .. |
| 16:39.45 | dhill | is that safe? |
| 16:39.49 | rene- | digium.com down for me |
| 16:40.34 | danp | dhill: i guess it dependds on who could possibly control that IP |
| 16:41.26 | danp | if it's a basically secure internal network it probably doesn't really matter |
| 16:41.33 | dhill | its over internet |
| 16:41.38 | dhill | he controls the end user device |
| 16:42.01 | rene- | does the digium bugtracker has a mirror? |
| 16:42.29 | dhill | but if a malicious person knows the static IP and the sip server.. could they send spoofed SIP packets with the customer's source IP.. and cause problems? |
| 16:42.58 | *** join/#asterisk qdk (n=qdk@0xc213c3df.inet.dsl.telianet.dk) |
| 16:43.08 | danp | dhill: it's definitely possible, yes |
| 16:43.49 | *** join/#asterisk h0 (n=fakhir@unaffiliated/fakhir) |
| 16:44.01 | dhill | ok, one last Q for now |
| 16:44.03 | dhill | :) |
| 16:46.04 | danp | go for it |
| 16:47.47 | dhill | i have an adtran 908 (drops out 8 pots).. say ports 1 - 5 are part of a hunt group for phone number 1112223333. I setup users 1112223333-01, -02 and so on. Then I do Dial(SIP/${EXTEN}-01), Dial(SIP/${EXTEN}-02), and so forth... |
| 16:47.56 | dhill | it works just fine |
| 16:48.13 | *** join/#asterisk lorinc (n=ang@caracas-3441.adsl.interware.hu) |
| 16:48.28 | danp | okay |
| 16:48.33 | dhill | but am i making it more work? |
| 16:48.36 | dhill | or is that a typical setup |
| 16:49.14 | Corydon76-home | dhill: is the Adtran a SIP gateway or are you using a T1 card to interface? |
| 16:49.31 | dhill | adtran takes a t1 in.. and drops off 8 ports |
| 16:49.41 | dhill | and is the sip gatewa |
| 16:49.41 | dhill | y |
| 16:50.11 | danp | and you're trying to receieve calls from it, right? |
| 16:50.18 | Grnd-Wire | dhill: How much did that Adtran (and all the right modules) cost you? |
| 16:50.19 | dhill | and make calls |
| 16:50.23 | Corydon76-home | So what you'd probably do is set up two group= lines in zapata.conf, say group=1 and group=2, then do an autoselection of the first available port, via Dial(Zap/g1/${EXTEN}) |
| 16:50.33 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 16:50.33 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 16:50.47 | dhill | i dont have Zap |
| 16:51.00 | Corydon76-home | You're not doing T1 to the adtran? |
| 16:51.06 | dhill | no |
| 16:51.11 | dhill | data t1 |
| 16:51.24 | Corydon76-home | Hmmm, why? |
| 16:51.35 | dhill | we have customers that have a data t1 |
| 16:51.38 | dhill | and want voip |
| 16:51.56 | dhill | so these adtrans handle a data t1.. and are a sip gateway.. do nat, dhcp, etc.. and drop off pots lines |
| 16:52.46 | dhill | Adtran Total Access 900 |
| 16:52.48 | Corydon76-home | Sounds like you need to ask Adtran how to do it, then |
| 16:54.29 | dhill | i mean.. it works just perfect now.. i was just wondering if it was typical to setup a sip user for each line in a hunt group i guess |
| 16:54.34 | Corydon76-home | If I was doing the same thing, I'd put an Asterisk box in there mastering a data T1 with SIP phones, and running to a voip provider |
| 16:54.52 | Grnd-Wire | dhill: You know Adtran has AWESOME pre and post-sales engineering support, right? They'll design the entire system for you, and tell you how to program it! :D |
| 16:55.19 | dhill | i'll shoot them an email |
| 16:55.20 | Corydon76-home | Or even a hybrid T1/PRI with several B-channels for voice and the rest data |
| 16:56.03 | Corydon76-home | Say, 1 d-channel, 5 b-channels, and 18 data channels grouped together into one. |
| 16:56.37 | Corydon76-home | Then you'd have all the advantages of a PRI, plus a good bit (>1Mb) of data |
| 16:56.44 | dhill | we used to do that with channelized t1's |
| 16:56.54 | dhill | but voip is easier |
| 16:57.03 | Corydon76-home | voip provider? |
| 16:57.29 | dhill | we are the voip provider |
| 16:57.44 | dhill | we have PRI's fed into cisco as5300's |
| 16:57.45 | *** join/#asterisk _VoicePulse (n=contact@unaffiliated/voicepulse) |
| 16:57.52 | dhill | and cisco does sip to asterisk |
| 16:58.11 | `Sean | lol |
| 16:58.14 | *** join/#asterisk acehunky (n=chat_jok@203.124.217.98) |
| 16:58.16 | `Sean | <3 Cisco |
| 16:58.18 | acehunky | hello |
| 16:58.20 | `Sean | i want a 7985 |
| 16:58.21 | `Sean | :D |
| 16:58.28 | acehunky | can any one help me .. why i might be getting "Unexpected CAS bit pattern" |
| 16:58.42 | Corydon76-home | dhill: so on the customer premise, you're breaking out POTS lines? |
| 16:58.44 | acehunky | i am trying to get asterisk work on MFC/R2 signalling |
| 16:58.54 | Corydon76-home | dhill: instead of using SIP phones? |
| 16:58.59 | dhill | correct |
| 16:59.11 | acehunky | is there anyone who can help me with MFC/R2 stuff out here ? |
| 16:59.16 | dhill | companies dont want to change their phone system just yet :) |
| 16:59.22 | dhill | too much $$$ |
| 16:59.40 | Corydon76-home | If you say so |
| 17:00.03 | dhill | we don't touch the customer side |
| 17:00.16 | Corydon76-home | Ah, we're all about the customer side |
| 17:00.27 | dhill | ahh |
| 17:00.40 | Corydon76-home | It's much easier to put in a PRI and put customers on SIP phones... works better, too |
| 17:00.48 | Corydon76-home | POTS is an awful technology |
| 17:01.03 | dhill | these adtrans can drop out a pri too |
| 17:01.10 | dhill | they have a pri interface |
| 17:01.14 | *** join/#asterisk stkn|work (n=stkn|wor@gentoo/developer/pdpc.active.stkn) |
| 17:01.24 | Corydon76-home | Yeah, but it's better just to do PRI direct to the telco |
| 17:01.26 | dhill | so we just do voip from us to customer.. and drop out pots or pri |
| 17:01.42 | Corydon76-home | There's far more that you can do with a PRI, and the sound quality is better, too |
| 17:02.06 | dhill | we are a clec |
| 17:02.41 | Corydon76-home | Are you doing QOS over that data T? |
| 17:02.49 | dhill | but a customer who has a data t1 .. and pays ATT for 4 pots lines.. easier to just just do voip to us |
| 17:02.52 | dhill | yes |
| 17:02.53 | dhill | LLQ |
| 17:03.21 | dhill | we port their numbers.. they plug their 4 lines into the adtran |
| 17:03.22 | dhill | all set |
| 17:03.26 | dhill | not more paying ATT |
| 17:03.49 | rene- | how to do a transfer out of a queue and make the transferer drop off the call zap-openerQueue---closerQueue ? |
| 17:03.55 | dhill | ok, gotta run |
| 17:04.13 | rene- | i have seen several msgs on the mailing lists |
| 17:04.15 | EmleyMoor | I'm just a home user - but where one likes old phones and the other has special needs, and we sometimes need to be on the phone at the same time |
| 17:04.19 | rene- | that report this |
| 17:04.24 | acehunky | anyone with MFC/R2 expereince out here ? |
| 17:05.53 | *** join/#asterisk osiris (n=osiris@c-71-205-27-131.hsd1.mi.comcast.net) |
| 17:07.37 | *** join/#asterisk jpablo (n=jpablo@linuxuanl.org) |
| 17:08.00 | jpablo | hey people, what would you recommend for a E1 cards, sangoma, rhino or digium ? |
| 17:08.26 | acehunky | jpablo go for the cheapest one :) |
| 17:08.39 | acehunky | sangoma is a better deal though |
| 17:08.54 | jpablo | acehunky: I need reliability and good support. |
| 17:09.03 | jpablo | acehunky: why? |
| 17:09.35 | acehunky | jpablo sangoma has good support |
| 17:09.46 | *** join/#asterisk kFuQ (n=somedude@c-67-185-123-34.hsd1.wa.comcast.net) |
| 17:10.48 | rene- | i dont want to go to asterisk-dev and look silly there saying that queue transfers are broken because dont allow to drop off the transferer until the call has finished |
| 17:10.50 | jpablo | acehunky: are you familiar with the rhino R1T1 ? I have had very good experience with rhino support. |
| 17:11.25 | *** join/#asterisk hohum (n=dcorbe@c-71-62-76-68.hsd1.va.comcast.net) |
| 17:11.26 | acehunky | jpablo well then go for them .. why ask on the list ? |
| 17:11.57 | jpablo | acehunky: Support is only secondary after reliability. |
| 17:12.22 | jpablo | Good audio quality and stability are more important to me than good support. |
| 17:12.39 | acehunky | jpablo well then sangoma is good choice .. |
| 17:12.50 | jpablo | ok |
| 17:12.53 | Grnd-Wire | jpablo: Yeah, we don't WANT to be calling support - except if the world is crashing down on us. :) |
| 17:13.09 | acehunky | i havent gone back to check with my customer location once i installed A101 Single Span PRI card |
| 17:13.44 | acehunky | jpablo well u dare care digium for support of these cards .. (well they dont get answered fast .. better is to come on IRC) |
| 17:13.46 | Grnd-Wire | acehunky: How long ago was that? |
| 17:13.46 | acehunky | instead of phone |
| 17:14.01 | acehunky | i am doing the second year annual maintenance contract for them :) |
| 17:14.02 | *** join/#asterisk oQPa (n=uawename@15.Red-83-40-197.dynamicIP.rima-tde.net) |
| 17:14.35 | Grnd-Wire | Sweet! I had a hard time with your last sentence. Are you saying you don't like Digium support, and it's hard to get ahold of them? |
| 17:15.04 | acehunky | yeah .. |
| 17:15.09 | acehunky | its hard to get hold of them .. |
| 17:15.18 | acehunky | they are busy building lot of things :) |
| 17:15.29 | acehunky | rpath .. asterisknow .. etc etc .. |
| 17:15.37 | Grnd-Wire | but they're willing to connect to the machine and figure out what is going wrong.. Doesn't that count for something? Or is that normal with Rhino and Sangoma too? |
| 17:16.36 | acehunky | Grnd-Wire connect to machine is something that you get even from the last end reseller :) |
| 17:16.42 | jpablo | I rember once rhino asking me for a shell. |
| 17:17.29 | acehunky | and the best part .. they dont list out their resellers and their distributors are selling directly to end consumers . Gee that kills the entire chain of Distributor - Resellers ! |
| 17:17.31 | Grnd-Wire | huh.. ok |
| 17:18.15 | Grnd-Wire | acehunky: Again, referring to Digium? Well in all fairness, their prices are ALOT higher than if you go with a reseller.. and they do have a lookup for resellers on their website.. ? |
| 17:19.00 | *** join/#asterisk sahafeez (n=sahafeez@ip68-6-215-70.sd.sd.cox.net) |
| 17:19.35 | acehunky | well thats one more valid point .. |
| 17:19.43 | jpablo | <PROTECTED> |
| 17:19.43 | jpablo | <PROTECTED> |
| 17:19.46 | jpablo | eek |
| 17:19.49 | jpablo | supid mouse. |
| 17:19.56 | jpablo | so, I guess i'll go with sangoma. |
| 17:21.34 | Strom_M | the fud machine wins again! |
| 17:21.42 | jpablo | jeje |
| 17:21.51 | jpablo | i guess if thoses redfones are worth a look |
| 17:22.28 | Grnd-Wire | Strom_M: FUD? On my part? I just said their prices are higher on the website than a reseller, and they do have a list of resellers available.. ? |
| 17:22.48 | *** join/#asterisk SLiNK (n=KNOCK@c-68-63-34-189.hsd1.al.comcast.net) |
| 17:24.41 | jpablo | Strom_M: I already have a dual E1/T1 card from digium and it was a PITA to get it working, it crashed a lot in my sun server. |
| 17:24.50 | *** join/#asterisk [TK]D-Fender (n=joe@64.235.216.2) |
| 17:26.27 | *** join/#asterisk Gunnar (n=gunnar@nat.sigmasoft.com) |
| 17:37.35 | *** join/#asterisk h0 (n=fakhir@unaffiliated/fakhir) |
| 17:39.51 | *** join/#asterisk Chris-NB (n=chris@argos.campus-sbg.at) |
| 17:41.48 | *** join/#asterisk EriSanHome (n=EriSan@81-174-35-6.f5.ngi.it) |
| 17:42.38 | osiris | i work for a voip provider, and i'm interested in setting up an asterisk box, just to see how it works and what it's all about. what would you guys recomend (cpu/ram wise) for a basic asterisk system |
| 17:42.58 | danp | if you just want to play with it it doesn't take much at all |
| 17:43.02 | Strom_M | osiris, what kind of call load are you expecting to handle on the box? |
| 17:43.04 | osiris | will an old 800 w/ 128M be enough ? |
| 17:43.13 | osiris | well, 1 to start |
| 17:43.14 | danp | to mess around, sure |
| 17:43.35 | danp | i use an old celeron 500 with 128M RAM as my home PBX |
| 17:43.36 | EmleyMoor | osiris: I experimented with it on a much worse system - it was fine except for its own sounds |
| 17:43.46 | Strom_M | for 1 call, 800mhz with 128M RAM is plenty |
| 17:43.58 | osiris | how many would you say that COULD handle |
| 17:44.03 | EmleyMoor | I use my only P4 as mine - but that's because I had it spare |
| 17:44.24 | danp | i think you'd be surprised |
| 17:44.27 | osiris | im kind of looking for a rle of thumb here i guess |
| 17:44.33 | Strom_M | osiris, that's a complex question. are you transcoding? |
| 17:44.34 | osiris | er rule of thumb |
| 17:44.51 | osiris | not sure, but will be using g711u for codec |
| 17:45.12 | Strom_M | and only g711u? |
| 17:45.18 | osiris | yep |
| 17:45.31 | osiris | could use others, but that is the primary one |
| 17:45.35 | Strom_M | ok, so no transcoding |
| 17:45.46 | EriSanHome | anyone using YAC with * |
| 17:45.50 | osiris | i DO want it to be g722 capable to show off our new polycom HD phones |
| 17:46.03 | *** join/#asterisk tzafrir_laptop (n=tzafrir@bzq-88-155-125-67.red.bezeqint.net) |
| 17:46.04 | Strom_M | 1.4 can do g722 passthrough |
| 17:46.09 | osiris | kewl |
| 17:46.27 | osiris | damn if those soundpoint 650's dont sound awesome |
| 17:47.18 | Strom_M | osiris, on my 1ghz p3 with 128 megs of RAM, as a single user I was easily able to get 10+ calls going without a hitch |
| 17:47.20 | [TK]D-Fender | osiris : G722 is pretty worthless. Only works inside your building, and we're talking about PHONE calls here... Hardly worth the extra cost vs the lower models |
| 17:47.47 | *** join/#asterisk sahafeez (n=sahafeez@ip68-6-215-70.sd.sd.cox.net) |
| 17:47.48 | osiris | i understand. but when cost isnt the issue |
| 17:48.24 | osiris | and im not sure about the 722 inside the building alone. i called from 650 to 650 outside our net, and it still sounded HD grade |
| 17:48.33 | joe | anyone running asterisk on an smp machine, that compiled it themselves? |
| 17:49.05 | joe | weirdness w/ the Makefile when calling make w/ smpflags |
| 17:50.33 | danp | joe: i am, what's up? |
| 17:50.33 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 17:50.35 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 17:51.04 | *** join/#asterisk Bazy (n=bazy@86.125.51.251) |
| 17:51.07 | joe | danp: when you build it what smp flags do you pass it? |
| 17:51.34 | *** join/#asterisk Alakazamz0r (n=Alakazam@198.170.183.130) |
| 17:51.38 | joe | thought that running make w/ -j1 would avoid a problem in the make file but it doesn't |
| 17:51.52 | danp | you modified the makefile for SMP? |
| 17:52.14 | danp | i just did 'make'. do you have some error output you could paste somewhere? |
| 17:52.20 | *** join/#asterisk sasch (n=sasch@host102-30-static.107-82-b.business.telecomitalia.it) |
| 17:52.45 | tzafrir_laptop | -j1 may work around broken dependencies decorations |
| 17:52.48 | sasch | hi all |
| 17:52.51 | joe | danp: so the problem is if you run it w/ make -j1 vs just make |
| 17:52.59 | tzafrir_laptop | decelerations, that is |
| 17:53.11 | joe | tzafrir_laptop: the issues is it doesn't |
| 17:53.27 | tzafrir_laptop | joe, could you be more specific? |
| 17:53.49 | danp | i guess i'm not sure what you're talking about...both make and make -j1 work fine for me |
| 17:54.14 | tzafrir_laptop | danp: is this Asterisk? |
| 17:54.19 | danp | yeah |
| 17:54.56 | danp | a recent checkout of the 1.2 branch |
| 17:56.42 | joe | danp, tzafrir_laptop: -j1 causes issues for me b/c the target for include/asterisk/version.h doesn't get made before the rest of the targets shoot of all the other targets, and you get a race condition. |
| 17:56.57 | joe | I could be interpreting this wrong |
| 17:57.07 | joe | but I thought -j1 was basically the same as w/o it |
| 17:57.37 | joe | since -j Specifies the number of jobs (commands) to run simultaneously. |
| 17:57.40 | danp | right |
| 17:57.55 | tzafrir_laptop | -j1 means *no* parallel building |
| 17:58.14 | RoyK | tzafrir_laptop: as in 'synonymous to not using -j at all' |
| 17:58.16 | danp | well, i just finished with -j1. i did a make clean beforehand and just verified that it deletes include/asterisk/version.h |
| 17:58.28 | joe | right which is what's soo damn weird and makes me think there is a bug in the makefile |
| 17:58.51 | tzafrir_laptop | so if -j2 solves it, it is still a problem |
| 17:58.53 | danp | and i just kicked off a make -j5 and i saw it create version.h |
| 17:59.17 | *** part/#asterisk mog (i=ejabberd@c-71-207-215-93.hsd1.al.comcast.net) |
| 17:59.19 | joe | thanks, danp must be something else then |
| 17:59.25 | tzafrir_laptop | danp, any chance you have a clock skew issue (see such warnings from make?) |
| 17:59.32 | danp | nope |
| 17:59.41 | EriSanHome | if i need to fire an action on an incomming call (int & ext), in what context should i put my command ? |
| 17:59.53 | danp | the output of this looks basically the same as make or make -j1 |
| 18:00.17 | blitzrage | EriSanHome: the context you assigned for the peer |
| 18:02.09 | danp | albeit busier |
| 18:02.09 | tzafrir_laptop | (context is actually in the user, not peer) |
| 18:02.09 | blitzrage | tzafrir_laptop: I use peer for both directions |
| 18:02.10 | tzafrir_laptop | danp, any hint from 'make -n'? What order do you see there? |
| 18:03.56 | danp | http://pastie.caboo.se/33038 |
| 18:04.15 | danp | it dies not too long after that but that's to be expected |
| 18:05.24 | *** join/#asterisk DaveCanoe (n=Dave@H235.C72.B0.tor.eicat.ca) |
| 18:08.20 | *** join/#asterisk die_z (n=dieeasy@host159-115-static.104-80-b.business.telecomitalia.it) |
| 18:09.49 | joe | tzafrir_laptop: I'm confused now. are you saying there is or isn't a problem w/ the Makefile for smp boxen? |
| 18:14.44 | EmleyMoor | What's a suitable speed for Morse code when used for a ring cadence? |
| 18:15.33 | joe | hehe |
| 18:15.39 | Strom_M | EmleyMoor, you win the "bizarrest question of the week" award |
| 18:15.47 | joe | I second that |
| 18:15.59 | Qwell | bizarrest? |
| 18:16.34 | EmleyMoor | I have them on a 125ms-based speed at the moment, but wonder if slower might be better |
| 18:21.17 | EmleyMoor | ... especially as I'm sounding them on a bell |
| 18:22.52 | Strom_M | single-gong or dual-gong? |
| 18:23.10 | EmleyMoor | Dual |
| 18:24.10 | Strom_M | see, why do morse code? why not just have "riiiiiing" for home and "riing riing" for work? |
| 18:24.54 | EmleyMoor | I have one of those for internal calls, one for external, before considering my two work needs ("H" is the initial of a special customer we deal with) |
| 18:25.23 | EmleyMoor | (I also use the three rings and pause for external camp) |
| 18:26.06 | Strom_M | as much as I love analog phones, do yourself a favor and get a modern multiline voip set |
| 18:26.45 | EmleyMoor | I will give due consideration to that as and when... |
| 18:27.08 | EmleyMoor | Still awaiting approval on one of the uses anyway |
| 18:29.09 | *** join/#asterisk stkn|work (n=stkn|wor@gentoo/developer/pdpc.active.stkn) |
| 18:31.17 | *** join/#asterisk sahafeez (n=sahafeez@ip68-6-215-70.sd.sd.cox.net) |
| 18:38.41 | *** join/#asterisk ivanfm (n=ivanfm@c93481ec.virtua.com.br) |
| 18:39.44 | Lokiji | bye |
| 18:43.26 | *** join/#asterisk mtaht4 (n=m@c-71-198-23-124.hsd1.ca.comcast.net) |
| 18:44.41 | *** join/#asterisk karmatronic (n=karmatro@84.77.167.129) |
| 18:44.45 | *** part/#asterisk mtaht4 (n=m@c-71-198-23-124.hsd1.ca.comcast.net) |
| 18:48.09 | *** join/#asterisk kFuQ (n=somedude@c-67-185-123-34.hsd1.wa.comcast.net) |
| 18:49.46 | SLiNK | Anybody know right off why my AGI scripts exit with 0 and completed but perform no actions but did 6 months ago? |
| 18:50.15 | Qwell | a lot changes in 6 months |
| 18:50.17 | *** part/#asterisk oQPa (n=uawename@15.Red-83-40-197.dynamicIP.rima-tde.net) |
| 18:50.33 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 18:50.33 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 18:51.15 | SLiNK | hmmm 3 different scripts though |
| 18:51.26 | SLiNK | what might be a primary factor? |
| 18:52.19 | RoyK | SLiNK: try to run them manually |
| 18:52.43 | *** part/#asterisk Lokiji (n=Lokiji@ip-89-102-178-195.karneval.cz) |
| 18:53.09 | *** join/#asterisk rene- (n=pirruris@200.34.66.137) |
| 18:56.12 | *** join/#asterisk BSDTech (n=RNeese@ppp-69-238-75-25.dsl.irvnca.pacbell.net) |
| 18:56.53 | rene- | transfers from outside a queue |
| 18:57.13 | rene- | naah i am bored |
| 18:58.30 | BSDTech | who broke it |
| 18:58.32 | BSDTech | and why |
| 19:01.43 | *** join/#asterisk KuJaX (n=one@c-67-164-251-181.hsd1.ut.comcast.net) |
| 19:01.49 | *** join/#asterisk |dennis| (n=dennis@200.32.233.82) |
| 19:05.50 | *** join/#asterisk oQPa (n=uawename@15.Red-83-40-197.dynamicIP.rima-tde.net) |
| 19:10.22 | KuJaX | How does the Linksys LVS9000 compare to the functionality Asterisk has to offer? I am looking for an out of the box solution without a lot of admin overhead. |
| 19:10.51 | Strom_M | i believe the lvs9000 offers you a lot less flexibility |
| 19:12.39 | *** join/#asterisk ptblank (n=MURDER1@cpe-76-173-170-186.socal.res.rr.com) |
| 19:15.42 | battini | since when do out of the box and anything running on linux go together? =P |
| 19:15.48 | KuJaX | Strom_M: How about admin overhead though. I own a small business (less than 5 office employees) |
| 19:16.09 | KuJaX | and they area ll in the office thus I don't think I need the flexability Asterisk has to offer? |
| 19:16.18 | KuJaX | I have installed Trixbox, but have found it to be flakey at times. |
| 19:16.29 | Strom_M | well, trixbox is flaky by definition |
| 19:16.40 | KuJaX | and I know Asterisk is probably better as far as not flakey, but there is also a lot more to implement to have it working correctly. |
| 19:17.16 | Strom_M | KuJaX, i install this stuff professionally, and almost every client I have, regardless of size, wants some unique feature |
| 19:17.42 | Strom_M | asterisk's flexibility lets me say "yes, I can do that" in the vast majority of situations |
| 19:18.24 | Strom_M | and with a small office, once you have it set up, there will be little admin overhead apart from moves, adds, changes, and keeping the system upgraded from time to time |
| 19:19.30 | KuJaX | I see. So i guess it is just the initial setup. |
| 19:20.46 | KuJaX | The only thing I want is to have the 5 extensions work properly for both inbound and outbound with voicepulse. The ability for voicemails to be e-mailed to the appropriate employees email account, and an IVR type deal when customers call in where they can select sales or support or dial direct extension. The last thing is time conditions, when we close I want a different IVR/welcome message. Pretty simple? |
| 19:20.46 | Strom_M | that's all really easy |
| 19:21.36 | *** join/#asterisk alamantia (n=Anthony@65.4.1.65) |
| 19:22.14 | KuJaX | I will also be running SugarCRM on the linux (probably CentOS). I am also afraid that there may be some security holes. |
| 19:22.33 | KuJaX | Approximately how much time would it take to implement the above for a professional like yourself Strom_M? |
| 19:23.13 | Corydon76-home | I wouldn't go with CentOS unless I absolutely had to |
| 19:23.14 | Strom_M | apart from the sugarcrm, I could set up the above system easily within a business day |
| 19:23.28 | *** join/#asterisk bkruse_home (i=kruz@nat/digium/x-396bfbb29c147289) |
| 19:26.01 | Strom_M | and that includes all the testing and the "oh, and one more thing" features |
| 19:26.19 | WAudette | Corydon76-home: What do linux distro do you use? |
| 19:26.19 | Corydon76-home | Mandriva or Ubuntu |
| 19:26.38 | WAudette | Corydon76-home: I've been taking a poll lately. |
| 19:26.38 | Strom_M | i'm a debian guy, myself |
| 19:27.07 | *** join/#asterisk xheliox (n=jeff@pdpc/supporter/active/xheliox) |
| 19:27.07 | WAudette | I've heard a lot a people say Debian too. The ones that doen't like rpms like Debian. How does Ubunto deploy packages? |
| 19:27.25 | Strom_M | it's ubuntu, not ubunto |
| 19:27.25 | Strom_M | and ubuntu also uses apt :) |
| 19:27.26 | KuJaX | Problem is Strom_M that I am also already running Linksys SPA-941 phones. It seems like hardcoding everything in asterisk wouldn't be very cost effective as once it is done it won't be changed. One day for Asterisk, one hour for the Linksys IVR9000 |
| 19:27.26 | WAudette | lol... typo. Didn't mean to offend. |
| 19:28.13 | Strom_M | KuJaX, you can use those phones with asterisk |
| 19:28.16 | Corydon76-home | Ubuntu is a Debian derivative |
| 19:28.58 | Strom_M | KuJaX, and you may find that doing even the basic things you want to do may be difficult with that thing |
| 19:29.23 | Strom_M | i dont know how well it handles IVRs, call queueing, voicemail and email integration, etc etc |
| 19:29.49 | KuJaX | right. :( I just don't have time to implement this myself nor do I know someone locally that profession is in Asterisk setup |
| 19:29.58 | Strom_M | where's "locally"? |
| 19:30.06 | KuJaX | Salt LAke City |
| 19:30.41 | Strom_M | good old 801-land |
| 19:30.59 | KuJaX | indeedy |
| 19:31.19 | Strom_M | there are probably consultants in your area who can help you |
| 19:31.23 | Strom_M | check the voip-info wiki |
| 19:32.33 | Strom_M | alternatively, I could probably do quite a lot of the work for you remotely (I'm in Los Angeles) |
| 19:33.45 | KuJaX | I could install the minimal CentOS server installation and latest Asterisk, but it is the dialplan that I know would take me forever to implement. Everything else such as registering with Voicepulse and getting the SIP phones to register wouldn't be a problem. |
| 19:34.38 | WAudette | Corydon-w: D/Ling the latest Ubuntu ISOs now. |
| 19:35.18 | WAudette | Corydon76-home: Have you had your Weaties yet this morning? Care to help me w/ that issue I had on oss.conf? |
| 19:35.26 | WAudette | ;) |
| 19:35.31 | Corydon76-home | I'll check |
| 19:35.35 | Strom_M | KuJaX, well, fortunately, i can code dialplan in my sleep |
| 19:35.35 | battini | i wish i could install a spam filter on my tv. |
| 19:36.10 | WAudette | lol |
| 19:36.21 | WAudette | MythTV and fast forward button. |
| 19:38.13 | KuJaX | Strom_M: Check PM |
| 19:38.14 | Strom_M | i don't see a PM from you |
| 19:38.45 | battini | I had a media center box setup for awhile, but it didnt play nice with my dish 311 box |
| 19:39.43 | *** join/#asterisk obnauticus (i=asd@c-24-21-116-29.hsd1.mn.comcast.net) |
| 19:40.28 | WAudette | Corydon76-home: Do you remember where we left off? We were going to add a context [noanswer] to the existing [general] |
| 19:41.11 | WAudette | battini: Don't they sell a dual tuner pci decoder card for Dish and DirctTV yet? |
| 19:41.38 | battini | no idea |
| 19:41.43 | battini | I didnt look that far into it |
| 19:42.20 | battini | All i know is i was getting sick of going to watch tv and having 3 hours of 'you don't get this channel, please press channel up or down' |
| 19:46.50 | bkruse_home | zomgz |
| 19:47.09 | *** join/#asterisk [hC] (n=hardcore@S0106000fb51cc225.vf.shawcable.net) |
| 19:47.30 | battini | eloo bk |
| 19:50.33 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 19:50.33 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 19:51.28 | *** join/#asterisk obnauticus (i=asd@c-24-21-116-29.hsd1.mn.comcast.net) |
| 19:57.06 | bkruse_home | battini: sup! |
| 19:57.15 | bkruse_home | file: im not sure man ;[ we need IT! |
| 19:57.28 | bkruse_home | unfortunatly there is 0 IT personel here |
| 19:58.05 | The_LightSide | hiya Strom_C, how u feeling? ;p |
| 19:58.36 | bkruse_home | ~shoes |
| 19:58.46 | jbot | shoes is probably something that strom_M rambles about |
| 19:58.47 | Strom_M | hi |
| 19:59.00 | Strom_M | im waking up :) |
| 19:59.10 | The_LightSide | lol ok |
| 20:01.33 | *** join/#asterisk lorinc (n=ang@caracas-3441.adsl.interware.hu) |
| 20:01.41 | *** join/#asterisk andew (n=andew@andew.co.uk) |
| 20:01.59 | *** join/#asterisk DaveCanoe (n=Dave@H6.C30.B96.tor.eicat.ca) |
| 20:07.27 | *** join/#asterisk tzafrir_laptop (n=tzafrir@bzq-88-152-221-24.red.bezeqint.net) |
| 20:08.09 | tzafrir_laptop | I see that asterisk.org now looks OK with SeaMonkey. Thanks to whoever fixed it |
| 20:09.42 | brookshire | bkruse_home: ?? |
| 20:11.48 | The_LightSide | hey Strom_C, im still having the progress tone issue tho :( |
| 20:12.10 | bkruse_home | brookshire: woot, bugs.digium.com doesnt work? |
| 20:12.27 | Strom_M | The_LightSide, ok, let me put on pants or something |
| 20:12.40 | The_LightSide | lol, u mean u not in the office ;p |
| 20:12.48 | [hC] | holy shit. this utstarcom f1000g was fully charged last night when i went to bed, and now its dead. |
| 20:12.59 | Strom_M | The_LightSide, it's saturday |
| 20:13.01 | Strom_M | i'm at home |
| 20:13.09 | The_LightSide | OH SHIT! sorry dude! |
| 20:13.17 | The_LightSide | dont worry ;) |
| 20:13.30 | battini | who wears pants in the office? |
| 20:13.40 | Strom_M | i would at this point say something witty in afrikaans, but I don't know how to spell anything in afrikaans |
| 20:13.48 | EmleyMoor | [hC]: Dodgy battery? |
| 20:14.17 | [hC] | EmleyMoor: possibly! I hadnt used it up until today. I'll have to try that again. |
| 20:15.26 | The_LightSide | Strom_C, i completly forgot its a weekend |
| 20:19.10 | Strom_C | !! |
| 20:19.20 | Strom_C | i never forget it's a weekend |
| 20:20.08 | The_LightSide | lol, i never really have a weekend... its usually all work and no play |
| 20:22.29 | *** part/#asterisk pigpen (n=mark@fw.seamans.cc) |
| 20:22.53 | RoyK | The_LightSide: sounds boring |
| 20:23.15 | The_LightSide | yip... but thats the entertainment industry for u |
| 20:24.04 | bkruse_home | brookshire: is that server in the closet? |
| 20:27.26 | SomeOne1 | how do you make an extension act different depending on the time of the day |
| 20:27.26 | *** join/#asterisk Jabroni (n=Hercules@red-corp-200.76.249.142.telnor.net) |
| 20:27.32 | SomeOne1 | someone was showing me their dialplan |
| 20:27.34 | SomeOne1 | i forgot how it goes |
| 20:27.39 | *** join/#asterisk xheliox (n=jeff@pdpc/supporter/active/xheliox) |
| 20:28.54 | Jabroni | Guys anyone knows where could I grab the latest firmware/app for my polycom 301?? I bought it from voipsupply like a year ago, tried contacting polycom but they said that I need to contact my reseller.. and voipsupply wont give it out to me |
| 20:32.14 | WAudette | Voipsupply has an ftp site for getting them. |
| 20:32.16 | *** join/#asterisk s1gny|wrk (n=s1gny@p54914B89.dip.t-dialin.net) |
| 20:33.04 | WAudette | Send a request via their support form requesting access and they'll email you a username and password. |
| 20:33.20 | WAudette | Jabroni: ^^^ |
| 20:33.54 | billf | hmm |
| 20:33.59 | billf | where is the bugs site? |
| 20:34.38 | WAudette | Corydon76-home: I have to head out for a bit. I'll PM you w/ my contact information. |
| 20:43.02 | *** join/#asterisk Hansin321 (n=eric@c-67-190-5-42.hsd1.co.comcast.net) |
| 20:48.01 | *** join/#asterisk paavum (n=dorphals@pcsp163-73.supercabletv.net.co) |
| 20:48.13 | paavum | Hello can anybody help me debug a sip connection? |
| 20:50.33 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 20:50.33 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 20:50.40 | tzafrir_laptop | paavum, as a more specific question |
| 20:52.03 | paavum | http://www.pastebin.ca/315721 |
| 20:52.12 | paavum | there it is |
| 20:52.17 | paavum | the output of a sip debug |
| 20:52.24 | paavum | and my config file |
| 20:52.50 | The_LightSide | does anyone know if zaptel 1.2.12 has a issue with immediate=yes? |
| 20:55.47 | paavum | My qyestion is |
| 20:55.58 | paavum | I have somebody with a cisco trying to connect to my server |
| 20:56.01 | paavum | but I get that |
| 20:56.44 | paavum | what could be wrong?? |
| 20:57.03 | tzafrir_laptop | The_LightSide, immediate=yes in zapata.conf? It will simply be ignored.. |
| 20:57.28 | tzafrir_laptop | What Cisco exactly? |
| 20:57.34 | The_LightSide | where should it be? it always used to work with the older versions |
| 21:00.22 | tzafrir_laptop | Wow, why haven't I used ssh's ControlMaster before? Quite handy |
| 21:00.43 | The_LightSide | and also y does the TE110P not work properly with zaptel 1.10.X and below? |
| 21:00.54 | *** join/#asterisk |dennis| (n=dennis@200.32.233.82) |
| 21:01.41 | The_LightSide | unless its the libpri giving hassels... |
| 21:03.51 | tzafrir_laptop | The_LightSide: 1.0.x? |
| 21:05.07 | The_LightSide | erm.. sorry i have a issue that the TE110P does not recognise the E1 link from zaptel version 1.2.10 and below |
| 21:05.35 | paavum | tzafrir_laptop --> I'm finding out |
| 21:06.00 | The_LightSide | and now im running 1.2.12 and i need the immediate function, as well as early media/inband progress tones |
| 21:08.58 | *** join/#asterisk lefant (n=lefant@muybridge.danyx.com) |
| 21:13.43 | paavum | We have a Nextone MSW |
| 21:13.51 | paavum | trying to connect to an asterisk 1.2.14 |
| 21:14.46 | paavum | the output of the sip debug is in http://www.pastebin.ca/315721 |
| 21:19.02 | The_LightSide | this te110p was the worst card evr to be developed |
| 21:19.16 | *** join/#asterisk ptblank (n=MURDER1@cpe-76-173-170-186.socal.res.rr.com) |
| 21:20.20 | bkruse_home | in zaptel.conf 0 for timing source means im the timing source correctg? |
| 21:20.22 | bkruse_home | correct* |
| 21:21.52 | The_LightSide | tzafrir, where should the immediate =yes be placed for it to work? |
| 21:22.09 | The_LightSide | Strom_C, i figured out the inband progress tones issue |
| 21:23.13 | *** join/#asterisk fetcher (n=jnh@ip-209-172-35-240.reverse.privatedns.com) |
| 21:23.19 | Corydon76-home | WAudette: ping |
| 21:28.01 | *** part/#asterisk oQPa (n=uawename@15.Red-83-40-197.dynamicIP.rima-tde.net) |
| 21:31.52 | *** join/#asterisk vgster (n=vgster@cpc2-ledn1-0-0-cust826.leed.cable.ntl.com) |
| 21:34.49 | EmleyMoor | I presume asterisk can take decisions based on the number of digits dialed? |
| 21:37.28 | EmleyMoor | (so I could use _[378]XXXXXXX to match a local number in London for example?) |
| 21:38.20 | danp | that is correct |
| 21:38.39 | danp | assuming that pattern really matches london stuff |
| 21:39.06 | EmleyMoor | All London numbers are 8 digits and begin with 3, 7 or 8 |
| 21:39.32 | *** join/#asterisk Skarmeth (n=Skarmeth@201009050090.user.veloxzone.com.br) |
| 21:42.45 | *** join/#asterisk riddlebox (n=james@75-132-205-166.dhcp.stls.mo.charter.com) |
| 21:44.25 | *** join/#asterisk sahafeez (n=sahafeez@ip68-6-215-70.sd.sd.cox.net) |
| 21:45.04 | bkruse_home | zaptel.conf, timing source = 0 means that im the timing source, right? |
| 21:45.17 | *** join/#asterisk BSDTech (n=RNeese@ppp-69-238-75-25.dsl.irvnca.pacbell.net) |
| 21:45.26 | The_LightSide | i sure hope so ;p |
| 21:48.18 | bkruse_home | k |
| 21:48.19 | bkruse_home | ;] |
| 21:50.33 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 21:50.33 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 21:52.34 | bkruse_home | no....... |
| 21:52.42 | The_LightSide | oh :/ |
| 21:52.47 | bkruse_home | when its set to 0 that means that the span is NOT used as primary timing source |
| 21:52.52 | bkruse_home | :X |
| 21:53.00 | The_LightSide | lol ok... |
| 21:53.22 | bkruse_home | battini: :] |
| 21:53.33 | bkruse_home | who was the dude having the te110p problem |
| 21:53.40 | The_LightSide | me |
| 21:54.03 | battini | so i was hungry right, and I made some sausage...in guiness |
| 21:59.33 | Hansin321 | I just downloaded * 1.4. I have a wildcard101 FXO interface so I can connect my server to my phone line. I obviously need the Zaptel package also. What about Libpri (I have no T1/E1 interfaces)? I would like to install the least amount of stuff possible. Also, are sounds separate from the main install now |
| 21:59.45 | Hansin321 | ? Do I need the Sounds package also? Thanks. |
| 22:00.41 | *** join/#asterisk Gunnar (n=gunnar@nat.sigmasoft.com) |
| 22:06.23 | *** join/#asterisk axisys (n=axisys@c-69-143-190-152.hsd1.va.comcast.net) |
| 22:08.28 | *** join/#asterisk ShadowHntr (n=sentinel@wikipedia/Shadowhntr) |
| 22:12.44 | *** join/#asterisk obnauticus (i=asd@c-24-21-116-29.hsd1.wa.comcast.net) |
| 22:13.18 | fetcher | Hansin321: Gentoo's package system includes "basic" / common sounds for voicemail, IVR etc. in the main asterisk package, and puts less-common things (weather, home automation etc.) in a separate asterisk-sounds |
| 22:13.25 | *** join/#asterisk aptura (n=sales@S010600a0c93f6f7e.vs.shawcable.net) |
| 22:15.42 | *** join/#asterisk Soul (n=Soul@87-196-105-234.net.novis.pt) |
| 22:20.28 | rene- | battini: cool |
| 22:20.36 | *** join/#asterisk linlin (i=will@71.194.70.13) |
| 22:21.21 | battini | rene- it was damn good. |
| 22:22.34 | *** join/#asterisk pder (n=pder@cpe-69-133-88-135.twmi.res.rr.com) |
| 22:23.36 | pder | i am having problems dialing out when my POTS lines are configured with kewlstart. it does work with loopstart however. can anyone help? |
| 22:28.45 | *** part/#asterisk pder (n=pder@cpe-69-133-88-135.twmi.res.rr.com) |
| 22:29.54 | Hansin321 | Unless I am using ISDN, I don't need to install Libpri, right? Even if I do need Zaptel for use with Wildcard101 FXO interface? I have read somewhere where they recomended to intall it just because, but I don't think I need it. Anyone know off hand? Thanks. I have been looking around but can't find definite answer. |
| 22:30.33 | x86 | shouldn't need it |
| 22:30.35 | wiljacket | Hansin321: Try it and post to a wiki your results |
| 22:30.47 | wiljacket | but I dont think it loads on my FXO setup |
| 22:31.01 | x86 | but the bristuff patch adds a lot of cool functionality that you may desire, even if you dont have a BRI circuit |
| 22:31.21 | Hansin321 | wiljacket: Sounds good. I am going to test it out... |
| 22:33.12 | *** join/#asterisk SurfnKid (n=SurfnKid@unaffiliated/surfnkid) |
| 22:33.22 | wiljacket | if you are using a wildcard101 you will want to rule out all of the possible problems that you can, probably doesnt hurt to comple libpri.. it's a small build |
| 22:33.46 | *** join/#asterisk blitzrage (n=blitzrag@asterisk/documenteur-extraordinaire/blitzrage) |
| 22:33.54 | *** join/#asterisk CrashHD (n=crashhd@c-67-182-167-222.hsd1.ca.comcast.net) |
| 22:34.00 | SurfnKid | http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&rd=1&item=230075617970 |
| 22:34.44 | *** part/#asterisk SurfnKid (n=SurfnKid@unaffiliated/surfnkid) |
| 22:34.50 | b11d | heh |
| 22:34.55 | b11d | what a bastard |
| 22:36.24 | wiljacket | oh come on, it sounds like a great deal |
| 22:36.26 | wiljacket | <PROTECTED> |
| 22:36.50 | wiljacket | how many laptops posted to ebay have LCD 150% top shape |
| 22:37.18 | monsted | 0 |
| 22:38.02 | monsted | it'd almost be worth buying it just to give him a crap rating |
| 22:39.19 | b11d | hahaha |
| 22:39.48 | b11d | i've got a strange issue.. if i have an extension in one context, it fails.. if i put it into a different context, it works.. |
| 22:40.06 | b11d | but both contexts appear to be the same, only named differently for organization |
| 22:40.39 | wiljacket | b11d: I've had problems liek that which were fixed just by ordering the contexts differently (order of operations problem), could that be it? |
| 22:41.02 | b11d | possibly.. |
| 22:41.10 | *** join/#asterisk oQPa (n=roque@15.Red-83-40-197.dynamicIP.rima-tde.net) |
| 22:41.26 | b11d | did you see anything obviously wrong, or did you just reorder them to see if it would work? |
| 22:41.27 | wiljacket | when you load the extensions in the cli do you see different priorities? |
| 22:41.48 | wiljacket | pretty much kept running extensions reload, seeing what was there and then hitting the system as I watched |
| 22:42.01 | b11d | hrm.. both show up in "show dialplan" |
| 22:42.36 | b11d | when its in the context [it] it dials the correct sip peer.. but when its in [msha] it tries to dial back out another zap channel.. when it should go to a sip peer.. |
| 22:45.11 | wiljacket | top to bottom in the dialplan, is [it] after [msha]? |
| 22:45.30 | b11d | it is before msha |
| 22:45.31 | b11d | :) |
| 22:45.52 | wiljacket | can you put up your extensions.conf on pastebin.ca? |
| 22:46.00 | b11d | yeah give me a few mins |
| 22:46.27 | *** join/#asterisk Ryushin (i=proxy@windwalker.openinnovations.com) |
| 22:50.33 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 22:50.33 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 22:54.47 | aptura | rene, you can have our -5 C weather |
| 22:55.25 | blitzrage | -5C here... and that's practically spring |
| 22:55.48 | lters | 59.7 F :) |
| 22:56.25 | Druken | can i use asterisk as a SIP passthrew? |
| 22:56.26 | rene- | here is like 28 C but the fuckers wont breathe without the ac on |
| 22:56.34 | rene- | i like warm weather |
| 22:56.51 | Druken | never mind, stupid question... course i can... bah! |
| 22:57.16 | b11d | -35 C here last night |
| 22:57.34 | rene- | but i work at a call center in cancun where the agents are from the us and what can i say gringos dont like the warm weather as much as me |
| 22:57.47 | battini | 39f here. |
| 22:58.06 | aptura | btw looking at putting together a ultra low power embeded asterisk system can anyone make some recomendations? Power requirments of 25 watts or less if possible. |
| 22:58.24 | rene- | aptura a soekris box powered over ethernet? |
| 22:58.45 | aptura | you speaking from experaince rene |
| 22:58.52 | aptura | I know of the soekris box. |
| 22:58.56 | rene- | linksys wrt powered over ethernet |
| 22:59.07 | aptura | needs one pci slot for fxo |
| 22:59.08 | rene- | no i am just talking my ass |
| 22:59.13 | rene- | then soekris |
| 22:59.19 | rene- | i havent used them |
| 22:59.21 | rene- | but |
| 22:59.27 | rene- | i know they can be powered over ethernet |
| 22:59.40 | rene- | i dont know if that leaves enough power for them to power a pci card |
| 22:59.43 | monsted | soekris are great little boxes |
| 22:59.46 | aptura | you mean powered by poe? |
| 23:00.05 | rene- | yes |
| 23:00.12 | aptura | k |
| 23:00.15 | b11d | fxo will require far more than 45 watts |
| 23:00.24 | b11d | so its virtually out of the question |
| 23:00.25 | b11d | for PoE |
| 23:00.26 | aptura | If its solar powered in remote locations even better. |
| 23:00.26 | rene- | isnt fxs |
| 23:00.40 | *** join/#asterisk simonc_ (n=simon@62.3.101.121) |
| 23:00.49 | rene- | the one that demands tons of energy for ringing , b11d? |
| 23:01.18 | aptura | s as in signaling renea. That is what the co puts out to your home phone. Dial,tone signaling. so in my cased its fxo. |
| 23:02.17 | rene- | ok |
| 23:02.40 | b11d | yeah |
| 23:02.49 | b11d | i guess it is fxs that would generate rings and such |
| 23:03.08 | rene- | so if you want to plug an analog phone you couldnt power it if you used POE? |
| 23:03.26 | rene- | or what you coulnt power is a trunk/line from the CO? |
| 23:03.47 | x86 | rene-: the CO line is already powered |
| 23:03.51 | b11d | yeah |
| 23:04.02 | rene- | ok |
| 23:04.35 | monsted | rene-: FXS eats a lot of power, FXO doesn't |
| 23:04.52 | rene- | aptura: i was dreaming of using a generator attached to a model plane mini diesel engine |
| 23:05.04 | rene- | with some diesel depot |
| 23:05.06 | aptura | Co sends 90 volts to your house phone and the co generates a dial tone and ring signaling in the local loop. |
| 23:05.19 | monsted | hmm |
| 23:05.20 | aptura | rena a mini generator? |
| 23:05.26 | rene- | aptura: yes |
| 23:05.38 | rene- | as a backup for solar |
| 23:05.47 | monsted | how much power can you steal from the Co via the phone line? :) |
| 23:05.58 | aptura | I have been resurching mini generators for some time as a backup source of power from my diesel truck. |
| 23:06.01 | rene- | monsted: that is a great idea hhehe |
| 23:06.25 | rene- | aptura: cool |
| 23:06.44 | aptura | Only mini generars are typical small generaors such as kuboto and yanmar. |
| 23:07.06 | rene- | ohh |
| 23:07.12 | rene- | never heard of those |
| 23:07.46 | rene- | how small they can be> |
| 23:07.48 | rene- | ? |
| 23:09.10 | aptura | size of a motorcycle |
| 23:09.11 | aptura | engine |
| 23:09.20 | Druken | anyone know if you can relay the vmwi status via SIP ? |
| 23:09.31 | rene- | it is not that big |
| 23:09.57 | rene- | i am sure they could power the box very easily |
| 23:10.30 | rene- | maybe something smaller could be built from a diesel rc engine? |
| 23:10.51 | rene- | you dont want to go and put diesel on the thing all the time |
| 23:12.00 | x86 | Druken: that's what SIP's SUBSCRIBE message is used for ;) |
| 23:12.55 | rene- | x86 if my phone can light its MWI led is it possible that can also subscribe the other leds to check presence for other lines? |
| 23:12.55 | Druken | x86: uhmm... think you can learned me?? i'm trying to run the vmwi threw a intermediate asterisk server |
| 23:15.24 | aptura | btw, are there any gms/wifi phones that switch over from gsm to wifi in the absence of gsm signaling? |
| 23:24.55 | *** join/#asterisk CrashHD (n=crashhd@c-67-182-167-222.hsd1.ca.comcast.net) |
| 23:29.47 | *** join/#asterisk BitBandit (i=McDonald@68-187-56-58.dhcp.stgr.ut.charter.com) |
| 23:35.54 | RoyK | I'll sue sid maier |
| 23:38.14 | *** join/#asterisk bkruse_home (n=kruz@69.73.127.92) |
| 23:39.17 | EmleyMoor | If I want to have a universal "force X provider" code prefix, what would people suggest? I want standard dialing available but a code available to force calls over each provider (and, in one case, with a given caller ID). |
| 23:40.15 | niZon | # codes |
| 23:40.29 | *** join/#asterisk De_Mon (n=de_mon@fl-76-4-98-162.dhcp.embarqhsd.net) |
| 23:40.36 | EmleyMoor | Ah, problem: I also need them reachable from a rotary phone |
| 23:40.58 | niZon | ouch |
| 23:41.08 | niZon | 10 10 codes then |
| 23:41.10 | monsted | EmleyMoor: so far, i've used a 0 prefix for "best effort" and 6-9 prefixes for the various providers |
| 23:41.25 | EmleyMoor | 0 = non-local prefix here |
| 23:41.31 | niZon | oh |
| 23:41.44 | De_Mon | aargh chanspy has crashed 4times in the last hour I need to upgrade from 1.2.13 :/ |
| 23:41.54 | monsted | well, you can just define that people must hit 0 first to get an outside line |
| 23:42.39 | EmleyMoor | At present, I use 5X for two of them and plan to migrate the third (currently on 6) tomorrow to 57X (where X is the last digit of the caller ID to present) |
| 23:43.37 | EmleyMoor | (neither local nor internal numbers begin with 5 at present, and no announcement has been made as to the use of 5 to start local numbers) |
| 23:44.11 | SomeOne1 | can you switch back to the main dialplan/extensions.conf once you've done Switch to realtime? |
| 23:48.28 | *** join/#asterisk SirThomas_Home (n=tomc@209-169-198-159.us.warpdriveonline.com) |
| 23:50.02 | *** join/#asterisk shido6 (n=shido6@d221-68-200.commercial.cgocable.net) |
| 23:50.33 | *** part/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 23:50.33 | *** join/#asterisk Bhaal (i=bhaal@freenode/staff/bhaal) |
| 23:53.44 | *** join/#asterisk bkruse_home (n=kruz@69.73.127.92) |
