| 00:07.15 | *** join/#brlcad nKf (i=fKn@p54B53C9E.dip.t-dialin.net) |
| 00:07.20 | nKf | hi |
| 00:08.04 | nKf | which c++ preprocessor should i use for compiling brlcad? |
| 00:08.59 | brlcad | hello |
| 00:09.06 | brlcad | any |
| 00:09.24 | brlcad | if you're getting a c++ preprocessor error, it usually means that a preprocessor isn' |
| 00:09.27 | brlcad | isn't installed |
| 00:09.35 | brlcad | er, that c++ isn't installed |
| 00:09.44 | brlcad | the C preprocessor should work fine as well |
| 00:10.03 | brlcad | might get away with ./configure CXXCPP=cpp |
| 00:10.31 | nKf | well, cpp is installed (3.4 and 4.0) but none of them seems to work |
| 00:10.50 | brlcad | is g++ installed? |
| 00:11.02 | brlcad | or tried the CXXCPP=cpp? |
| 00:12.01 | brlcad | need to run out, back in 2 hours.. :/ |
| 00:12.35 | nKf | g++ ? i use ubuntu.. i found no g++ package |
| 00:13.29 | nKf | in config.log i see the following message: "cannot exec cc1plus: no such file..." |
| 00:14.08 | nKf | ok, see you later or tomorrow, thanks anyway |
| 00:22.22 | nKf | strange thing, you are right... g++ is not installed... |
| 00:24.06 | nKf | now it work.. thanks a lot... byebye |
| 01:27.16 | *** join/#brlcad Guu` (i=guu@myth.gibbscam.com) |
| 05:49.44 | *** join/#brlcad brlcad_ (n=sean@bz.bzflag.bz) |
| 05:51.04 | *** mode/#brlcad [+o brlcad] by ChanServ |
| 07:30.41 | *** join/#brlcad clock_ (n=clock@84-72-62-188.dclient.hispeed.ch) |
| 09:03.27 | *** join/#brlcad clock_ (n=clock@zux221-122-143.adsl.green.ch) |
| 12:14.03 | *** join/#brlcad clock__ (n=clock@zux221-122-143.adsl.green.ch) |
| 17:23.17 | *** join/#brlcad pier (n=pier@151.56.253.233) |
| 18:21.00 | pier | Hi everyone |
| 18:21.33 | pier | a questin about replication and referencing |
| 18:22.41 | pier | What is the differences between the two procedures in building them? |
| 18:22.50 | pier | I mean the commands |
| 18:22.56 | pier | used |
| 18:47.23 | brlcad | which commands? or is that what you're asking? |
| 18:47.46 | brlcad | in general when you create a combination with the g or comb commands, they are simply references, not copies, of the objects |
| 18:47.53 | brlcad | cp replicates an object |
| 18:48.32 | brlcad | yet if you cp a combination, it only replicates that combination, not the objects that are referenced inside that combination |
| 18:48.55 | brlcad | there is a way to perform a "deep copy", but the command escapes me right this second |
| 18:49.03 | brlcad | and is generally discouraged ;) |
| 18:49.33 | brlcad | if you cp a primitive, it replicates that primitive just like how it replicates a combination |
| 18:52.48 | pier | as a matter of fact I created a combination |
| 18:53.01 | pier | then copied it |
| 18:53.23 | pier | and moved as a matrix in the right place |
| 18:53.41 | pier | made several cp of the same comb |
| 18:53.52 | pier | and placed them but |
| 18:54.28 | pier | when a change in a dimension called this wasn't reflected in the other objects |
| 18:54.46 | pier | perhaps I did somethig wrong |
| 19:24.01 | *** join/#brlcad clock_ (n=clock@84-72-91-59.dclient.hispeed.ch) |
| 19:53.39 | pier | Sorry, my fault... it works ... perhaps had one two many |
| 20:01.42 | pier | too |
| 20:27.23 | pier | Brlcad.. the translation of the second volume is getting on |
| 20:27.28 | pier | slowly though |
| 20:28.19 | pier | I hope to be able to work on it full time as soon as I get rid of some dead lines |
| 21:30.30 | *** join/#brlcad ChanServ (ChanServ@services.) |
| 21:30.30 | *** mode/#brlcad [+o ChanServ] by irc.freenode.net |
| 21:33.24 | *** part/#brlcad pier (n=pier@151.56.253.233) |
| 21:46.39 | *** join/#brlcad nelson (n=nelson@rrcs-72-43-17-50.nys.biz.rr.com) |
| 21:47.35 | nelson | ignorant question: can I use BRL-CAD to design plastic parts and then send off to a fab shop to have them made? |
| 22:38.02 | *** join/#brlcad clock_ (n=clock@84-72-61-2.dclient.hispeed.ch) |
| 22:51.29 | *** join/#brlcad nelson_ (n=nelson@rrcs-72-43-17-50.nys.biz.rr.com) |
| 23:06.07 | ``Erik | depends on the format the fabricator can take... |
| 23:19.00 | brlcad | nelson_: for the most part, it can assuming the fab shop groks one of the formats brl-cad exports |
| 23:36.12 | ``Erik | (finding out if the plastic part has the structural integrity to exist, however, is a different problem :) ) |
| 23:45.03 | nelson_ | So I should locate a fab shop first, and then ask them. Okay, will do, thanks. |
| 23:46.10 | ``Erik | yeah, I have a feeling "stl" is a common format, and brlcad exports stl files, but some places want them in a certain arrangement, so make sure to ask |
| 23:46.19 | ``Erik | (like print fabricators want them 'layered' |
| 23:46.19 | ``Erik | ) |
| 23:50.40 | *** join/#brlcad nKf (i=fKn@p54B56E76.dip.t-dialin.net) |
| 23:51.00 | nKf | hi |
| 23:51.56 | nKf | i'm back again with new questions :) while compiling i got this error message: ../../src/libdm/.libs/libdm.so: undefined reference to `XFreeDeviceList' |
| 23:52.28 | nKf | is a library missing? what could be the problem? |
| 23:56.26 | ``Erik | X |
| 23:56.42 | ``Erik | that's an Xlib function... |
| 23:59.43 | nKf | but xlib and xlib-dev ist installed |