| 01:44.39 | *** join/#edev bigbootay (n=bigboota@CPE0004e28a9289-CM000a73a14ed4.cpe.net.cable.rogers.com) |
| 03:35.41 | *** join/#edev bigbootay (n=bigboota@CPE0004e28a9289-CM000a73a14ed4.cpe.net.cable.rogers.com) |
| 03:59.29 | *** join/#edev chouimat|Zzzz (n=dieu@r2351064.cidc.net) |
| 04:10.19 | *** join/#edev Karo-sam (i=karosa@ob-889.adsl.datanet.hu) |
| 04:24.37 | *** join/#edev sunrunner20 (n=jamesdoe@pool-71-252-248-115.dllstx.fios.verizon.net) |
| 08:06.31 | lkm | T0mW: Yestarday i take schemes. Etherner chip address wire is directly connected to general. |
| 08:08.32 | lkm | T0mW: Also, reading into chip documentation, after reset it must return 0x3000 on base address + 0x0A, until i write some data to it. So i map all 128 MB space and in cycle i read all adresses + 2 |
| 08:12.35 | lkm | T0mW: But not find this value anywhere. |
| 08:17.22 | *** join/#edev redblue (i=star@ppp024.108-253-207.mtl.mt.videotron.ca) |
| 11:06.21 | T0mW | lkm: well, as I said before, you have to break the problem into two steps: |
| 11:06.36 | T0mW | lkm: 1. verify that the Chip Select is working. |
| 11:06.54 | T0mW | lkm: 2. then work on the driver. |
| 11:07.47 | T0mW | lkm: you have written the code, now you need to debug it. |
| 11:12.13 | T0mW | lkm: that is where an oscilloscope or logic probe would help |
| 12:05.26 | *** join/#edev chouimat|Zzzz (n=dieu@r2351064.cidc.net) |
| 13:32.02 | *** join/#edev leoncamel (n=leoncame@219.142.143.88) |
| 13:47.21 | *** join/#edev GPSFan (n=kenm@12.10.255.248) |
| 13:47.21 | *** mode/#edev [+o GPSFan] by ChanServ |
| 14:22.55 | *** join/#edev leoncamel (n=leoncame@219.142.128.47) |
| 14:35.29 | *** join/#edev linac (n=lin@121.71.54.49) |
| 15:07.31 | T0mW | prpplague: screw usb |
| 15:44.08 | *** join/#edev ChanServ (ChanServ@services.) |
| 15:44.09 | *** mode/#edev [+o ChanServ] by irc.freenode.net |
| 15:48.44 | prpplague | T0mW: hehe |
| 15:48.47 | prpplague | T0mW: troubles? |
| 15:57.34 | *** part/#edev bigbootay (n=bigboota@CPE0004e28a9289-CM000a73a14ed4.cpe.net.cable.rogers.com) |
| 17:01.16 | *** join/#edev chouimat (n=dieu@kde/developer/chouinard) |
| 17:06.58 | *** join/#edev redblue (i=star@ppp173.108-253-207.mtl.mt.videotron.ca) |
| 18:17.23 | *** join/#edev purl (i=ibot@pdpc/supporter/active/TimRiker/bot/apt) |
| 18:17.23 | *** topic/#edev is #edev discussion for small embedded device development and hacking || http://www.elinux.org/wiki/ || http://www.hackaday.com || http://www.linux-hacker.net || buildroot now has a mailing list, please subscribe at http://buildroot.busybox.net |
| 18:58.18 | *** join/#edev purl (i=ibot@pdpc/supporter/active/TimRiker/bot/apt) |
| 18:58.18 | *** topic/#edev is #edev discussion for small embedded device development and hacking || http://www.elinux.org/wiki/ || http://www.hackaday.com || http://www.linux-hacker.net || buildroot now has a mailing list, please subscribe at http://buildroot.busybox.net |
| 19:42.21 | *** join/#edev silverpower (n=shrike@adsl-234-211-250.cha.bellsouth.net) |
| 19:59.30 | *** join/#edev kakaroto (n=cerne@2001:5c0:8fff:fffe:0:0:0:5b4f) |