IRC log for #edev on 20080102

00:13.11cajakaSpeedEvil, the chart looks good. I think prpplague said the 3.3v out was maxed at 100ma.
00:18.23GPSFanSpeedEvil: in your chart, pin 32 should be EINT13, not EINT15. Which is pin 30.
00:23.40*** join/#edev bbradley_ (n=bbradley@5ac808a0.bb.sky.com)
00:24.04SpeedEvilI should have spotted that - 29-30-31-32 are not a subtle clue :)
00:24.24SpeedEviloh - right
00:24.33SpeedEvilthey are 'misordered' normally.
00:24.40SpeedEvilthat's probablyt what confused me
00:26.45SpeedEvilanyway - fixed
00:27.45SpeedEvilIt'd be so nice if the chip could route arbitrary lines to the output.
00:53.18cajakaWhat are your guys thoughts on shifting "Hammer details" onto a separate page? That way we could go into high detail about the supported interfaces(SPI, I2C, LCD, etc).
00:56.37cajakanvm
00:57.21SpeedEvilProbably sensible.
00:57.32SpeedEvilI was intending to make the various bits of the table into links.
00:57.41SpeedEvilclick the 'spi' section, and ...
00:58.07cajakaI just noticed there is already a hardware page.
04:52.36*** join/#edev dijenerate (n=dijenera@72.51.111.182)
05:54.55*** join/#edev LyosNorezel (n=LyosNore@unaffiliated/lyosnorezel)
06:30.02LyosNorezelanyone around?
06:34.18davidc__what didja want LyosNorezel ?
06:34.57LyosNorezeldavidc_: any recommendations on/for a MIPS toolchain
06:34.59LyosNorezel?
06:36.15LyosNorezelRedhatter: think that'll work on Fedora 7?
06:36.36RedhatterDirectly, no.  Prefixed portage tree?  Perhaps.  chroot?  No problem.
06:36.58LyosNorezelhmmm
06:37.01davidc__yeah, I use crossdev too.. or build from scratch myself
06:37.07davidc__but building from scratch is a huuuge PITA
06:37.20RedhatterYour easiest bet if you wanted to go that route, would be to grab a Gentoo stage3 tarball, unpack that somewhere, and chroot into it when you want a cross toolchain.
06:38.01RedhatterDan Kegel(sp)'s crosstool is a non-distro-specific option, but I'm not sure what the status of that is at the moment.
06:38.23LyosNorezelok... will a generic MIPS toolchain work for a jmr3927 compatible CPU?
06:38.53RedhatterWould I be right in guessing that thing is MIPS I or MIPS II based?
06:39.29LyosNorezelummm... honestly... I'm not sure
06:39.47LyosNorezelit's a TMPR3927 32bit toshiba processor
06:40.28RedhatterI'm pretty sure that thing is MIPS II
06:40.43RedhatterI had a PDA based on the TMPR3922U, which is MIPS II
06:40.51*** join/#edev DrZimmerman (n=theo@2001:5c0:8fff:fffe:0:0:0:6af1)
06:41.07LyosNorezelthat would make sense
06:41.09RedhatterBooted netbsd/hpcmips just fine
06:41.40Redhatter(although under NetBSD, it was useless... no PCMCIA and no framebuffer)
06:42.02LyosNorezellol
06:42.28LyosNorezelI don't need PCMCIA... though I will need to support 2 miniPCI device
06:42.29LyosNorezels
06:43.47RedhatterYeah, in this case, I suspect PCMCIA and the framebuffer sat behind a mystery chip that no-one knew anything about -- hence their non-functional status under NetBSD.
06:44.24RedhatterWindows CE of course, could see them, but I'm not sure how to get at the various parts of the kernel.  This is all academic now however, since the said PDA has died.
06:45.18LyosNorezelfun
07:05.32*** join/#edev Heet (n=lucas@a82-92-5-118.adsl.xs4all.nl)
08:00.15*** join/#edev redblue (i=star@ppp082.109-253-207.mtl.mt.videotron.ca)
08:35.59*** join/#edev DrZimmerman (n=theo@2001:5c0:8fff:fffe:0:0:0:6af1)
09:36.05*** join/#edev mmp (n=mmp@adsl-dyn11.78-98-166.t-com.sk)
09:52.02*** join/#edev redblue (i=star@ppp041.108-253-207.mtl.mt.videotron.ca)
10:17.10*** join/#edev linac (n=lin@222.76.84.82)
10:54.41*** join/#edev lyakh (n=lyakh@p57BD2A83.dip0.t-ipconnect.de)
11:52.06*** join/#edev flameman (n=root@host52-189-dynamic.50-82-r.retail.telecomitalia.it)
12:05.51*** join/#edev dijenerate (n=dijenera@72.51.111.182)
12:09.51*** join/#edev T0mW (n=Tom@24.238.86.158.res-cmts.sth.ptd.net)
12:19.51*** join/#edev linac (n=lin@121.41.66.29)
14:32.29*** join/#edev chouimat|work (n=mchouina@209.217.106.98)
14:33.16chouimat|workmorning
14:47.05*** join/#edev GPSFan (n=kenm@12.10.255.246)
14:47.06*** mode/#edev [+o GPSFan] by ChanServ
15:14.29*** join/#edev bbradley (n=bbradley@5ac808a0.bb.sky.com)
15:49.28dijeneratehappy new year everyone!
15:50.12dijenerateany of you guys using a linksys nslu2 with debian etch?
16:00.14SpeedEvilI can answer that!
16:00.18SpeedEvilAlas only with a no.
16:00.20SpeedEvilSorry :)
16:27.43Crofton|homehttp://people.debian.org/~terpstra/message/20071217.142656.9f55d329.en.html
16:52.36*** join/#edev samuelr (n=samuelr@dsl093-061-094.pit1.dsl.speakeasy.net)
17:02.27*** join/#edev prpplague (n=dave@ppp-70-244-175-101.dsl.rcsntx.swbell.net)
17:02.45prpplagueho ho hum
17:05.14chouimat|workhi prpplague
17:05.22prpplaguechouimat|work: greetings
17:05.34chouimat|workprpplague: happy 2008
17:05.55prpplagueyea yea whatever
17:05.57prpplaguehehe
17:07.56prpplaguexchat doesn't seem to like to keep my irc connection active for very long
17:08.12chouimat|workprpplague: I learned to day we have a release for the 14th ... and I also got a lot more  P1 tasks to do
17:08.59chouimat|workok bbl lunch
17:09.02chouimat|worktime
17:09.08prpplagueokie dokie
17:10.50prpplagueSpeedEvil: ping
17:12.15SpeedEvilopng
17:12.19SpeedEvils/op/po/;
17:12.37chouimat|workopng? Old PNG?
17:13.18prpplagueSpeedEvil: hey, i think all those pinouts and info for the hammer need to go on the hammer hardware page
17:14.08prpplagueSpeedEvil: you ordered a hammer board?
17:14.34SpeedEvilNot yet, getting money together - cashflow problems :/
17:14.40prpplagueahh
17:15.05SpeedEvilprpplague: yes - it probably should - I was just putting it there as I was referring to the diagram, as the diagram was confusing m.
17:15.07SpeedEvilme
17:15.32SpeedEvilI had hoped I could get away without using the hammer - for cost reasons - but it's probably not going to happen for V0
17:15.35prpplagueahh ok, you wanna move it to the hardware page?
17:15.48prpplagueSpeedEvil: what kind of project?
17:15.54SpeedEvilUAV
17:16.01SpeedEvilhttp://www.mauve.plus.com/test.png
17:16.12prpplagueSpeedEvil: ahh did you see the presentation on hackaday?
17:16.18SpeedEvilNo.
17:16.23prpplagueone sec url
17:16.25SpeedEvilwhat's it on?
17:17.07prpplaguehttp://www.hackaday.com/2007/12/27/24c3/
17:17.15prpplaguecould easily be used with the hammer
17:18.47SpeedEvilI'm not sure.
17:18.55SpeedEvilI'm in a very differnt space to them.
17:18.58SpeedEvilNo wings.
17:19.32SpeedEvil1Kg total weight or so. 35cm or so across the nacelles.
17:19.41prpplagueoh?
17:19.43prpplaguehow so?
17:22.36SpeedEvilIt's a ducted fan basically, with thrust vectoring surfaces in the output.
17:22.40SpeedEvilVTOL
17:23.00SpeedEviltakes off, ascends to 1Km or so, takes pic, lands on takeoff spot.
17:26.44prpplagueSpeedEvil: ahh interesting
17:26.54prpplagueSpeedEvil:  you ever done anything like that before?
17:27.22SpeedEvilI've done some RC design, and have played with thrust vectoring rocket nozzles (though only in cold flow)
17:28.03SpeedEvilThe other thing I like about it is that it can be moderately gradually tested.
17:28.13prpplagueahh
17:28.22SpeedEvilFirst takeoffs from a trampoline, tethered.
17:28.37prpplagueSpeedEvil: you wanna move those entries over to the hardware page? or do you want me to?
17:28.52SpeedEvilumm - I have no idea why, but FF is core dumping for me now.
17:29.17SpeedEvilI'd like to say I'm sure it's FF, but it may also be hardware.
17:29.39SpeedEvilso it's probably be quicker for you to move it over
17:35.50prpplagueSpeedEvil: okie dokie
17:56.23*** join/#edev bbradley_ (n=bbradley@5ac808a0.bb.sky.com)
18:24.44*** join/#edev flameman (n=root@host52-189-dynamic.50-82-r.retail.telecomitalia.it)
18:57.47*** join/#edev lyakh (n=lyakh@p57BD2A83.dip0.t-ipconnect.de)
19:20.47*** join/#edev landley (n=landley@cpe-72-177-114-214.austin.res.rr.com)
19:22.20*** join/#edev prpplague (n=dave@ppp-70-244-175-101.dsl.rcsntx.swbell.net)
19:38.29*** join/#edev prpplague (n=dave@ppp-70-244-175-101.dsl.rcsntx.swbell.net)
20:32.49*** join/#edev samuelr (n=samuelr@dsl093-061-094.pit1.dsl.speakeasy.net)
22:17.00*** join/#edev JonHylands (n=hylandsj@CPE001c102333bd-CM0014e88f58e0.cpe.net.cable.rogers.com)
22:17.20JonHylandsprpplague: you there?
22:23.16prpplagueJonHylands: hey
22:23.20prpplagueJonHylands: whats up?
22:23.35JonHylandsJust wanted to let you know I got the Hammer kit, looks good, it powers up fine
22:23.56JonHylandsIs there a build environment option for Windows?
22:24.46*** join/#edev prpplague (n=dave@ppp-70-244-175-101.dsl.rcsntx.swbell.net)
22:24.58prpplagueJonHylands: still there?
22:25.01JonHylandsyep
22:25.08prpplagueJonHylands: you get your kit?
22:25.11JonHylandsyes
22:25.18JonHylandsJust wanted to let you know I got the Hammer kit, looks good, it powers up fine
22:25.30prpplaguegood deal
22:25.37JonHylandsShould I ask tech questions on the forums?
22:25.51prpplagueJonHylands: i gotta finish cleaning up the garage , about 10 minutes, then i can chat
22:25.57JonHylandsI won't be here
22:26.00prpplagueor here
22:26.04JonHylandssorry, gotta go
22:26.08prpplagueJonHylands: np
22:26.13prpplagueJonHylands: yea on the forum is fine
22:26.16JonHylandsokay
22:26.29prpplagueJonHylands: lots of hammer folks here
22:26.36prpplagueJonHylands: so if you are online try here
22:26.40JonHylandsokay
22:28.44*** join/#edev prpplague (n=dave@ppp-70-244-175-101.dsl.rcsntx.swbell.net)
22:28.48*** part/#edev JonHylands (n=hylandsj@CPE001c102333bd-CM0014e88f58e0.cpe.net.cable.rogers.com)
22:29.11*** join/#edev prpplague (n=dave@ppp-70-244-175-101.dsl.rcsntx.swbell.net)
22:45.27ds2anyone got the recipe for loading a new uboot bin from within uboot itself?
23:03.59*** join/#edev linuxguy (n=linuxguy@dsl093-038-120.pdx1.dsl.speakeasy.net)
23:09.24RobotGuy<PROTECTED>
23:11.31flyback-http://en.wikipedia.org/wiki/List_of_device_bandwidths
23:13.22Roboteer<PROTECTED>
23:13.53RedhatterRoboteer, Nice password
23:14.34prpplaguelinuxguy: greetings
23:15.12SpeedEvil<PROTECTED>
23:15.39RobotGuyI had to register with a different nick because the ones I usually use are already taken. :)
23:16.01RobotGuy<-- Linuxguy on TinCanTools forums
23:16.25prpplagueRobotGuy: your kit should have shipped today
23:16.43SpeedEvilprpplague: can the store take paypal?
23:16.51RobotGuyWonderful!  I am looking forward to learning about and using the Hammer!
23:17.00prpplagueSpeedEvil: iirc yes
23:17.18SpeedEvilK.
23:17.49RobotGuyCan you e-mail me a tracking number so I will know when to expect my kit?
23:19.41SpeedEvilli: whaat're you doing with yours?
23:19.44SpeedEvilerr rob:
23:20.15prpplagueRobotGuy: yea you should get an email with the info
23:22.23ds2n/m the gumstix recipe worked well enough
23:23.40prpplagueds2: thats why i use apex, it's soooo easy
23:32.22*** join/#edev redblue (i=star@ppp117.108-253-207.mtl.mt.videotron.ca)
23:35.47prpplagueho ho hum
23:36.15prpplagueRobotGuy: we've send out a number of eval kit
23:36.32prpplagueRobotGuy: we are looking to get alot of talk going on the forum and on the wiki
23:53.30*** join/#edev cajaka (n=none@cpe-24-58-193-200.twcny.res.rr.com)

Generated by irclog2html.pl Modified by Tim Riker to work with infobot.