| 00:09.47 | *** join/#htc-linux cr2_ (n=cr2@ip-77-25-90-106.web.vodafone.de) |
| 00:31.16 | BabelO | cr2_, you use transparetn proxy ? |
| 00:31.24 | BabelO | i is just a forward iptables |
| 00:35.26 | cr2_ | BabelO: i've mounted the disk over ptp eth, and copied some broken rpms |
| 00:35.35 | cr2_ | so it's working again. |
| 00:35.54 | cr2_ | but running yast over ppp may be a better idea |
| 00:36.46 | cr2_ | BabelO: what do you suggest ? |
| 00:36.53 | dcordes_ | hi |
| 00:37.07 | BabelO | cr2_, yast over ppp should be slow |
| 00:37.07 | cr2_ | hi dcordes_ |
| 00:37.23 | BabelO | cr2_,where is your proxy ? |
| 00:37.30 | BabelO | hi dcordes_ |
| 00:37.51 | cr2_ | BabelO: i'may fix it on monday |
| 00:38.13 | BabelO | cr2_,else iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 80 -j REDIRECT --to-port 3128 |
| 00:38.15 | BabelO | is enough |
| 00:38.19 | BabelO | if squid is on your box |
| 00:38.22 | cr2_ | BabelO: i have nc10 as a gateway, and a notebook cnnected over ethernet. |
| 00:38.42 | BabelO | then just to the previous iptable on nc10 |
| 00:38.44 | cr2_ | BabelO: squid is already working |
| 00:38.59 | BabelO | as your other notebook should have nc10 in route table |
| 00:39.02 | cr2_ | BabelO: i'd like to run yast on the notebook |
| 00:39.04 | BabelO | as default |
| 00:39.59 | cr2_ | BabelO: what ports yast is using ? |
| 00:40.19 | BabelO | depend of the repo |
| 00:40.25 | BabelO | usaully it is http std |
| 00:41.08 | cr2_ | i'll check |
| 00:42.00 | BabelO | dcordes_, i can do back fly now with the t rex :) |
| 00:43.45 | cr2_ | BabelO: it's unhappy about dns |
| 00:43.52 | dcordes_ | BabelO: nice. I upgraded my side rudder today with balsa |
| 00:44.06 | BabelO | dcordes_, no aluminium |
| 00:44.14 | BabelO | with antenna to the floor |
| 00:44.49 | dcordes_ | BabelO: I think I will buy an industrial produced receiver antenna |
| 00:44.51 | cr2_ | hm. curl |
| 00:45.16 | BabelO | cr2_, on my suse , i need to configure curl by hand |
| 00:45.23 | BabelO | in /root/.curlrc |
| 00:45.30 | BabelO | option my hand |
| 00:45.36 | BabelO | the one set by yast are wrong |
| 00:46.13 | dcordes_ | BabelO: you mean I should use some aluminum plates as transmitter antenna? |
| 00:46.51 | BabelO | yes |
| 00:47.05 | BabelO | as a reflector |
| 00:47.16 | BabelO | so all go to the ground |
| 00:47.43 | dcordes_ | so instead of omni sending to all directions I wanna send only below the plane? |
| 00:47.47 | dcordes_ | or what is the idea |
| 00:48.00 | dcordes_ | right now I have the normal dipol onmni antenna |
| 00:48.33 | dcordes_ | I could cover the bottom of the plane with metal foil and mount the ant below that? |
| 00:50.41 | BabelO | if yes |
| 00:50.46 | BabelO | exactly |
| 00:50.56 | BabelO | to microwave go to the floor |
| 00:51.12 | BabelO | plane are like that |
| 00:51.20 | BabelO | no antenna on top |
| 00:51.24 | BabelO | only on bottom |
| 00:51.53 | dcordes_ | and they have metal fuselage.. |
| 00:52.05 | dcordes_ | interesting approach. I haven't seen that on the internet before |
| 00:52.25 | dcordes_ | can you propose some material to use? I have seen anti interference foil |
| 00:52.46 | dcordes_ | people used that to shield RC rx from video tx |
| 00:54.26 | BabelO | i will try aluminium like the one you use for food :) |
| 00:55.16 | BabelO | and antenna on the middle of the plane below the big plan |
| 00:57.58 | BabelO | two antenna should be good like we do on helicopter |
| 01:00.29 | dcordes_ | I have enough alumnium foil available. also I have the wiring perfect for putting the whole stuff on the bottom. no need for resoldering |
| 01:00.59 | BabelO | be carefull |
| 01:01.11 | dcordes_ | what do you mean by 'below the big plan' ? |
| 01:01.12 | BabelO | antenna should be isolated from the aluminium |
| 01:01.23 | BabelO | i look for the word :) |
| 01:01.30 | dcordes_ | wing?? |
| 01:02.18 | BabelO | yes middle of the wings |
| 01:02.45 | dcordes_ | ok. can I use the normal dipol biquad antenna? |
| 01:02.51 | dcordes_ | (like used for router) |
| 01:03.03 | dcordes_ | 802.11* ap |
| 01:03.14 | BabelO | should look like a V ? |
| 01:04.57 | dcordes_ | like a V? current antenna is just like the ones used for wifi |
| 01:05.46 | dcordes_ | http://www.quatech.com/catalog/images_big/wifi_antenna_DP002.jpg |
| 01:06.39 | BabelO | ok try with that first |
| 01:07.01 | BabelO | how much it works 800 m ? with the video ? |
| 01:07.28 | dcordes_ | with the biquad on the ground 800m should be doable |
| 01:07.51 | dcordes_ | a big problem is the orientation of the transmitter antenna |
| 01:08.21 | BabelO | yes |
| 01:08.25 | dcordes_ | when I fly sharp courbes |
| 01:08.35 | dcordes_ | and the antenna goes horizontal => noise |
| 01:08.35 | BabelO | with akluminium it should be better |
| 01:09.08 | dcordes_ | what about the orienation? when the antenna is at the botton, it's hard ot have it in vertical orientation. |
| 01:09.14 | dcordes_ | can I try horizontal? |
| 01:12.12 | dcordes_ | or I just flip it 180° and mount it so it can be flipped during landing (joint is flexible) |
| 01:12.48 | BabelO | you can't use a spring ? |
| 01:13.04 | dcordes_ | or a spring.. |
| 01:13.28 | dcordes_ | so that is no problem. but do you know a better microwave omni type than the normal dipole? |
| 01:13.58 | dcordes_ | there is enough space |
| 01:13.58 | dcordes_ | it's a pity if the tx ant sucks |
| 01:17.03 | BabelO | no |
| 01:17.14 | BabelO | no idea |
| 01:17.40 | dcordes_ | ok. I will try the bottom mounted aluminum foil vs dipole then |
| 01:17.58 | dcordes_ | flying backwards with the t-rex. you mean you can also stear while in backwards flight? |
| 01:18.19 | dcordes_ | just like you would fly straight ahead? |
| 01:20.49 | BabelO | i mean flying upside / down |
| 01:24.45 | dcordes_ | oh that's crazy |
| 01:25.22 | dcordes_ | it seems like you were flying a lot :) |
| 01:28.00 | Dunedan | is booting Android on his Blackstone :D |
| 01:31.42 | dcordes_ | Dunedan: with the msm_fb fix? |
| 01:32.35 | Dunedan | I'm just trying the zip from the wiki. |
| 01:32.41 | Dunedan | But it get's stuck during boot. :-/ |
| 01:34.35 | Dunedan | mmc1: host does not support reading read-only switch, assuming write-enable. |
| 01:34.36 | Dunedan | mmc1: new high speed SDHC card at address 8fe4 |
| 01:34.38 | Dunedan | mmcblk0: mmc1:8fe4 SU08G 7761920KiB |
| 01:34.39 | Dunedan | mmcblk0: p1 |
| 01:34.43 | Dunedan | these are the last messages |
| 01:34.47 | dcordes_ | display works? |
| 01:34.51 | Dunedan | yes |
| 01:34.56 | dcordes_ | ok nice |
| 01:35.08 | dcordes_ | boot angstrom |
| 01:35.25 | Dunedan | Debian would be nicer. ;-) |
| 01:35.28 | dcordes_ | maybe add a rootwait or rootdelay in cmdline |
| 01:36.45 | dcordes_ | the messages you pasted look normal |
| 01:37.07 | dcordes_ | you can use some initrd |
| 01:37.28 | dcordes_ | try this old kaiser initrd http://linuxtogo.org/~lgorris/kaiser-bootkit/angstrom-20081127.cpio.gz |
| 01:37.53 | dcordes_ | set INITRD angstrom-20081127.cpio.gz |
| 01:37.55 | dcordes_ | good night |
| 01:38.15 | Dunedan | yeah. got android booting. |
| 01:38.34 | Dunedan | seems only to work with plugged in usb in active sync mode. |
| 01:39.51 | Dunedan | dcordes_: Let me play a bit with android first. ;-) |
| 01:44.33 | Dunedan | dcordes_: Which kernel should I use? The android one? |
| 01:48.35 | BabelO | good night |
| 01:51.56 | Dunedan | dcordes_: Angstrom seems to run! |
| 01:52.00 | Dunedan | yeah |
| 02:04.56 | Dunedan | hum hum. Angstrom can't find some modules. So also dropbear still fail. |
| 02:13.15 | *** join/#htc-linux dcordes (n=dcordes@unaffiliated/dcordes) |
| 02:20.32 | Dunedan | dcordes: ping |
| 02:28.46 | *** join/#htc-linux Gentoon (n=Sean_Jon@unaffiliated/thesarge) |
| 02:30.13 | Gentoon | Whats up everyone? |
| 02:49.18 | *** part/#htc-linux Gentoon (n=Sean_Jon@unaffiliated/thesarge) |
| 03:46.14 | AstainHasPS3 | hiya |
| 04:08.46 | *** join/#htc-linux mrmoku` (n=mrmoku@ppp-93-104-48-226.dynamic.mnet-online.de) |
| 04:35.09 | *** join/#htc-linux woodson (n=CDP@c-68-54-66-168.hsd1.fl.comcast.net) |
| 04:41.43 | *** join/#htc-linux dzo_ (n=dzo@121-98-128-127.bitstream.orcon.net.nz) |
| 04:54.58 | *** join/#htc-linux dgmdan (n=dontspam@c-68-46-183-90.hsd1.pa.comcast.net) |
| 06:20.11 | *** join/#htc-linux Student (n=Student@62.16.118.7) |
| 06:35.51 | Marajin | hey AstainHasPS3 |
| 07:14.47 | *** join/#htc-linux dream_kill (n=nospam@92.56.48.66) |
| 07:40.53 | dgmdan | hey all |
| 07:42.42 | dgmdan | so what is "let's define a common setup" referring to anyway? |
| 07:42.59 | *** join/#htc-linux xutywx (n=pawel@195.205.38.92) |
| 08:26.16 | *** join/#htc-linux goxboxlive (n=goxboxli@185.84-48-126.nextgentel.com) |
| 08:34.22 | *** join/#htc-linux wdslbr (n=asa@dslb-088-069-211-174.pools.arcor-ip.net) |
| 08:38.03 | *** join/#htc-linux pleemans (n=toi@d54C2AAB7.access.telenet.be) |
| 08:44.37 | *** join/#htc-linux kiozen (n=oeichler@rgnb-5d87c436.pool.einsundeins.de) |
| 09:00.05 | *** join/#htc-linux goxboxlive_ (n=goxboxli@185.84-48-126.nextgentel.com) |
| 09:26.17 | *** join/#htc-linux goxboxlive (n=goxboxli@185.84-48-126.nextgentel.com) |
| 09:33.18 | *** join/#htc-linux tmzt (n=tmzt@adsl-76-244-156-116.dsl.akrnoh.sbcglobal.net) |
| 10:05.49 | dcordes | Dunedan: pong |
| 10:06.13 | dcordes | Kevin2: I think we can remove the android-msm and android-msm-htc-2.6.25 branches |
| 10:11.09 | *** join/#htc-linux yoyey (n=yoann@lns-bzn-49f-81-56-185-87.adsl.proxad.net) |
| 10:14.32 | *** join/#htc-linux Xime (n=xime@bankize.net) |
| 10:17.48 | *** part/#htc-linux yoyey (n=yoann@lns-bzn-49f-81-56-185-87.adsl.proxad.net) |
| 10:36.02 | *** join/#htc-linux nebi (n=nebi@170.ftth2.cust.fyrobs1.upps.se.borderlight.net) |
| 11:04.41 | Dunedan | dcordes: ping |
| 11:07.56 | Dunedan | dcordes: With our initrd I'm unable to create an ssh connection to the Blackstone, but it works with the initrd from the wiki. |
| 11:09.42 | *** join/#htc-linux Untouchab1e (n=Untoucha@cm-84.209.89.86.getinternet.no) |
| 11:09.46 | Untouchab1e | Good morning :) |
| 11:18.15 | *** join/#htc-linux DasBaum (n=DasBaum@p508F64B1.dip.t-dialin.net) |
| 11:19.49 | *** join/#htc-linux zycho (n=zycho@a89-182-215-223.net-htp.de) |
| 11:24.01 | *** join/#htc-linux Untouchab1e (n=Untoucha@cm-84.209.89.86.getinternet.no) |
| 11:32.55 | *** join/#htc-linux hechu (n=hechu@116.22.18.105) |
| 11:39.10 | *** join/#htc-linux marex (n=marex@vasut.kolej.mff.cuni.cz) |
| 12:13.58 | *** join/#htc-linux StarLite (n=nnscript@s55916ca6.adsl.wanadoo.nl) |
| 12:20.39 | *** join/#htc-linux BabelO (n=BabelO@unaffiliated/babelo) |
| 12:39.34 | *** join/#htc-linux he_chu (n=hechu@113.64.108.84) |
| 12:48.03 | *** part/#htc-linux DasBaum (n=DasBaum@p508F64B1.dip.t-dialin.net) |
| 12:54.11 | *** join/#htc-linux Zinbolic (n=chatzill@84.238.80.215) |
| 12:57.37 | dcordes | Dunedan: the wiki one has auto usb0 added in /etc/network/interface |
| 12:57.41 | dcordes | s |
| 12:58.26 | Dunedan | dcordes: well, without ssh your image might not useful or is there another way to access the device? |
| 12:59.48 | *** join/#htc-linux Zoolooc (n=fredsiba@nrbg-4dbfdddb.pool.einsundeins.de) |
| 13:00.08 | Dunedan | dcordes: Do you have some useful hints for building an own initrd? |
| 13:00.15 | dcordes | ppp but I don't know if it works correctly yet |
| 13:00.39 | dcordes | it's a gzipped cpio archive of the rootfs |
| 13:00.58 | dcordes | but why don't you use a partition on the sd card? |
| 13:01.27 | dcordes | does the touchscreen work? which kernel do you use? |
| 13:01.51 | Dunedan | I used the kernel which is also used for android 1.0 on Blackstone |
| 13:02.33 | Dunedan | touchscreen works with android, but I'm not sure if it works with angstrom too |
| 13:03.50 | dcordes | I don't know which kernel is used for android 1.0 on blackstone |
| 13:04.02 | Dunedan | and I don't use a partition on the sd card, because I'm new to this whole stuff and don't know what's possible, what's best practice and so on |
| 13:04.26 | dcordes | imo the best practice is to use a partition on the micro sd |
| 13:05.02 | Dunedan | hm |
| 13:05.03 | dcordes | where is the framebuffer fix discussed where's the kernel? do you have alink? |
| 13:05.18 | Dunedan | I assume android uses this kernel image: http://www.gavero.com/pichurri/blackstone/zImage |
| 13:05.32 | Dunedan | everything is mentioned on the wiki page: http://wiki.xda-developers.com/index.php?pagename=BlackstoneLinux |
| 13:05.38 | dcordes | ok |
| 13:05.55 | dcordes | ~seen pichurri |
| 13:05.57 | apt | pichurri <n=pichurri@users3.ilo.org> was last seen on IRC in channel #htc-linux, 10d 21h 24m 43s ago, saying: 'Marajin, saw the pics on the wiki? now a port to the latest version of 2.6.27 of the diamond is being developed...meaning sd support...etc'. |
| 13:06.28 | Dunedan | dcordes: So do you have any docu about additional partition on sd card, building own initrds and such stuff? |
| 13:06.50 | dcordes | http://www.gavero.com/pichurri/blackstone/pichurri_2.6.27_2009-03-03.diff |
| 13:08.44 | dcordes | Dunedan: I use gparted to parition sd card. in default.txt add root=/dev/mmcblk0pn where n is partition number to cmdline |
| 13:09.04 | dcordes | Dunedan: do you have OE? |
| 13:09.08 | Dunedan | hm, first problem: I don't have an SD-card reader. ;-) |
| 13:09.21 | Dunedan | nope, I don't have OE |
| 13:09.57 | dcordes | they are cheap. I think you can use the usb mass storage driver in wince to expose the card as a normal block device |
| 13:10.15 | dcordes | I like the direct microsd readers |
| 13:10.33 | dcordes | I got one from hama at saturn 10⬠|
| 13:10.37 | Dunedan | all right. But I think the additional partition will be the least problem. |
| 13:10.55 | Dunedan | If I've the partition how to proceed? |
| 13:11.39 | dcordes | have haret passing the root cmdline param ass described above |
| 13:11.58 | dcordes | and put whatever rootfilesystem on the partition of course |
| 13:12.13 | Dunedan | hm |
| 13:12.28 | Dunedan | that would work with every linux distribution? |
| 13:13.11 | dcordes | you can use debian |
| 13:13.17 | Dunedan | \o/ |
| 13:13.43 | Dunedan | That's what I wanted to hear. ;-) |
| 13:15.06 | dcordes | :) the pichurri patch applies fine with latest htc-msm-2.6.27 revision |
| 13:15.06 | *** join/#htc-linux kiozen (n=oeichler@rgnb-5d87c436.pool.einsundeins.de) |
| 13:15.50 | dcordes | I will ask him if we can comitt it |
| 13:20.12 | Dunedan | having this patches in the mainline kernel would be awesome. |
| 13:21.01 | dcordes | googel must get their stuff in mainline first |
| 13:21.22 | dcordes | then we will add the htc stuff |
| 13:26.31 | *** join/#htc-linux MethoS- (n=lem@host-091-097-247-067.ewe-ip-backbone.de) |
| 13:26.46 | dcordes | Dunedan: can you try a kernel build? |
| 13:27.11 | Dunedan | hm, maybe. If it's not to complicated. |
| 13:27.30 | dcordes | you replace zImage |
| 13:28.20 | Dunedan | well, trying one of your kernels is no problem. I thought I should build one. |
| 13:28.33 | *** join/#htc-linux wdslbr (n=asa@dslb-088-069-211-174.pools.arcor-ip.net) |
| 13:29.49 | dcordes | Dunedan: http://linuxtogo.org/~lgorris/builds/kernel/blackstone/zImage-htcblackstone-20090308-00 |
| 13:30.22 | dcordes | it's htc-msm-2.6.27 with http://www.gavero.com/pichurri/blackstone/pichurri_2.6.27_2009-03-03.diff built with htcraphael_defconfig |
| 13:30.24 | Dunedan | all right. Might take a while, because I'm doing some sd card backup now. |
| 13:30.59 | dcordes | ok just boot with the android rootfs and tell me if everything works like with the pichurri built zImage |
| 13:31.34 | Dunedan | ok |
| 13:32.34 | dcordes | thanks I'll be back later |
| 13:33.07 | dcordes | I need new hdd |
| 13:34.33 | *** join/#htc-linux zycho_ (n=zycho@a89-183-82-24.net-htp.de) |
| 13:41.31 | Dunedan | dcordes: yes. Your kernel image works exactly as good as the one from pichurri. |
| 13:51.15 | dcordes | ok http://git.linuxtogo.org/?p=groups/mobile-linux/kernel.git;a=commit;h=a7bbc84bc783acc349b030a4621541eab84165e0 |
| 13:51.40 | marex | hi |
| 13:51.47 | marex | is it possible to disable PXA OS timer 0 ? |
| 13:52.35 | marex | looks like I have a pending interrupt from it in ICPR when I boot and it hangs me |
| 14:04.53 | *** join/#htc-linux evildarknight (n=charles@41.207.133.92) |
| 14:35.25 | Kevin2 | dcordes: Send a note to the mailing list, and if no one objects after a few days then remove it. |
| 14:39.06 | *** join/#htc-linux hechu (n=hechu@113.64.108.84) |
| 14:40.34 | *** join/#htc-linux MethoS-- (n=lem@host-091-096-208-194.ewe-ip-backbone.de) |
| 14:46.11 | dcordes | Kevin2: they were intendet as pristine referrence to htc-msm and htc-msm-2.6.25 which are both obsolete |
| 14:48.29 | *** join/#htc-linux wippeout (n=wippeout@unaffiliated/wippeout) |
| 14:48.32 | wippeout | hello |
| 14:48.54 | wippeout | i just got a angstrom image for htc blackstone |
| 14:49.11 | dcordes | wippeout: hi |
| 14:49.18 | wippeout | the phone boots correctly with haret, i have a login with root |
| 14:49.31 | Kevin2 | dcordes: Okay - I'd still send a note to the mailing list - it can't hurt. |
| 14:49.53 | wippeout | what's the way to have a gui for ir |
| 14:49.54 | dcordes | Kevin2: yea thanks. I'm just saying fyi |
| 14:50.04 | *** join/#htc-linux c4software (n=c4softwa@roo49-2-88-161-139-221.fbx.proxad.net) |
| 14:50.13 | dcordes | wippeout: if you want to build it yourself, you can use openembedded |
| 14:50.14 | wippeout | i tried startx but it doesn't work :) |
| 14:50.22 | c4software | Hi everyone |
| 14:50.42 | wippeout | http://wiki.xda-developers.com/index.php?pagename=BlackstoneLinux |
| 14:50.50 | dcordes | lupine_85: can you provide him with your x image you used on raphael? |
| 14:50.52 | wippeout | i got the image from this wiki |
| 14:51.15 | Dunedan | wippeout: can you use the touchscreen with this image? |
| 14:51.21 | wippeout | yes |
| 14:51.28 | wippeout | i have a small keyboard |
| 14:51.32 | Dunedan | ah nice. Need to try it again later. |
| 14:51.34 | wippeout | on the top of the console |
| 14:51.40 | Dunedan | how do you got the keyboard? |
| 14:52.05 | dcordes | Dunedan: I think it's the kernel keyboard |
| 14:52.24 | Dunedan | hm. That didn't appear when I tried it. |
| 14:52.33 | wippeout | http://www.netripper.com/raphael/pics/20081027_touchscreen_keyboard2.jpg |
| 14:53.00 | wippeout | Dunedan: just to be sure to copy the images into the device root, not in the storage card |
| 14:53.09 | wippeout | and check your default.txt |
| 14:53.14 | wippeout | i had similar problem |
| 14:53.22 | Dunedan | ah, ok. I used another kernel. |
| 14:53.24 | wippeout | i had login without virtual keybord |
| 14:53.32 | Dunedan | And this kernel worked from storage card. |
| 14:53.37 | c4software | on the Diam and Raph the Navi Wheel have an init code ? |
| 14:53.41 | Dunedan | But this kernel doesn't seem to have the keyboar.d |
| 14:53.54 | wippeout | check the wiki, they told to install the image in the device root |
| 14:54.01 | dcordes | c4software: the scroll wheel on the side? |
| 14:54.05 | wippeout | not the device root |
| 14:54.16 | wippeout | perhaps due to path name |
| 14:54.16 | Dunedan | wippeout: sure, but I thought: hey, why not using it from the storage card if it works? ;-) |
| 14:54.27 | c4software | the scrool wheel on botom of the device |
| 14:54.27 | wippeout | Dunedan: mail the author ;) |
| 14:54.50 | Dunedan | I'm currently trying to setup Debian. So I don't wanna stick with Angstrom. ;-) |
| 14:55.02 | c4software | i change the rom of my diam and its don't work now. Strnage |
| 14:55.16 | dcordes | Dunedan: the blackstone kernel I built from git has the on screen keyboard enabled |
| 14:55.17 | wippeout | have you screenshots of your htc with linux ? |
| 14:55.33 | Dunedan | dcordes: Well, I tried your kernel only with android. ;-) |
| 14:55.54 | Dunedan | dcordes: But I'll try to use your kernel with debian later. |
| 14:56.04 | dcordes | Dunedan: it doesn't matter. the onscreen keyboard is drawn from the kernel to framebuffer |
| 14:56.11 | wippeout | have you info to add some gui feature to this image ? |
| 14:56.30 | dcordes | wippeout: you want an x11-image |
| 14:56.47 | wippeout | does debian work on htc ? |
| 14:56.55 | dcordes | wippeout: but you need to modify the kernel to use X. do you have htc-msm-2.6.27 locally? |
| 14:57.08 | wippeout | no, i'm newbie |
| 14:57.09 | Dunedan | wippeout: I'll know that a few hours. |
| 14:57.13 | Dunedan | +in |
| 14:57.15 | wippeout | i just got the pre builded images |
| 14:57.17 | dcordes | wippeout: ok I can make a zImage that works with X. |
| 14:57.26 | Dunedan | dcordes: ++ |
| 14:58.01 | wippeout | please not a bricked image |
| 14:58.03 | wippeout | :) |
| 14:58.16 | dcordes | Dunedan: it's a kernel config that enables a thread that refreshes the display. |
| 14:58.36 | dcordes | wippeout: it has the brick-guarantee. your phone will never power up again after it's booted |
| 14:58.45 | wippeout | hehe |
| 14:59.53 | dcordes | http://linuxtogo.org/~lgorris/builds/kernel/blackstone/zImage-htcblackstone-20090308-01-xfbdev |
| 15:01.41 | dcordes | this is a build with X http://linuxtogo.org/~lgorris/builds/OE/htcraphael/htcraphael/Angstrom-x11-sato-image-glibc-ipk-2008.1-test-20081207-htcraphael.rootfs.tar.gz |
| 15:02.06 | dcordes | this has X too http://linuxtogo.org/~lgorris/builds/OE/kensan/openmoko-shr-image-glibc-ipk--20081223-htckaiser.rootfs.tar.gz |
| 15:02.28 | dcordes | initrd with X http://linuxtogo.org/~lgorris/builds/OE/x11-image-120708.cpio.gz |
| 15:05.44 | wippeout | dcordes: thanks |
| 15:05.51 | wippeout | have you docs about building these ? |
| 15:07.52 | dcordes | lol the omapzoom looks so funny |
| 15:08.00 | dcordes | wippeout: http://www.angstrom-distribution.org/building-angstrom it's very easy |
| 15:08.36 | dcordes | wippeout: just use htcraphael or htcdiamond as machine |
| 15:09.29 | wippeout | no need to make patch , as indicated on the wiki ? |
| 15:11.38 | c4software | dcordes: You have an diamond right ? |
| 15:12.08 | Dunedan | dcordes: I'm having trouble to provide a correct root-cmdline option for debian. :-/ |
| 15:13.05 | Dunedan | "Plwas append a correct "root=" boot option; here are the available partitions:" |
| 15:13.11 | Dunedan | *Please |
| 15:13.48 | Dunedan | "Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)" |
| 15:14.40 | dcordes | Dunedan: sorry can' |
| 15:14.43 | dcordes | t help now |
| 15:14.56 | dcordes | c4software: bluangel, kaiser, kovsky |
| 15:15.01 | Dunedan | hm, schade ;-) |
| 15:15.05 | dcordes | wippeout: kernel patch? |
| 15:15.14 | c4software | ah oki, thanks. ^^ |
| 15:15.26 | wippeout | dcordes: thanks |
| 15:15.34 | c4software | I try to found a correct and clean rom for my diam :P. I had some problem with de the navipad... |
| 15:18.52 | dcordes | can't help with android |
| 15:19.34 | dcordes | wippeout: use htcblackstone machine instead. if you already did git-clone use git-pull to update. |
| 15:19.45 | dcordes | it will also make the kernel with xfbdev support |
| 15:24.52 | wippeout | for this moment, i just want to test |
| 15:25.02 | wippeout | perhaps, later i'll build my own image |
| 15:25.06 | wippeout | step by step :) |
| 15:30.05 | dcordes | lorl |
| 15:33.35 | wippeout | dcordes: have you the default.txt and haret.exe ? |
| 15:33.36 | wippeout | :) |
| 15:34.22 | dcordes | for which purpose? |
| 15:38.44 | wippeout | to boot your images |
| 15:40.40 | *** join/#htc-linux Venny (i=Travis@h216-45-127-2.dynamic.platinum.ca) |
| 15:45.22 | wippeout | dcordes: can you give me your default.txt |
| 15:45.50 | wippeout | in previous install, i don't make partition ext2fs and extract rootfs |
| 15:46.01 | wippeout | i just put 4 files on the fat sdcard |
| 15:46.22 | wippeout | angstorm.bin , default.txt, haret.exe, zImage |
| 15:49.57 | wippeout | i have error |
| 15:50.05 | Dunedan | hm. Something is wrong here. I've two partitions on my storage card. According to angstrom mmcblk0p1 and mmcblk0p2. The sceond one should be the ext2 partition with debian, but when I try to boot it, the kernel didn't find it. |
| 15:50.08 | wippeout | undefined MTYPE |
| 15:50.20 | wippeout | into the haret.exe |
| 15:52.09 | wippeout | i append the |
| 15:52.12 | wippeout | set MTYPE 2030 |
| 15:52.16 | wippeout | it boot |
| 15:52.17 | wippeout | s |
| 15:53.52 | wippeout | i freeze now |
| 15:54.06 | wippeout | mmcblk0 : p1 p2 |
| 15:56.53 | *** join/#htc-linux captnoord (i=4da104ed@gateway/web/ajax/mibbit.com/x-a2c5c44dcb3674b5) |
| 16:00.01 | wippeout | ok good now , angstrom X11 boots |
| 16:00.28 | wippeout | thank you all for your help |
| 16:00.29 | wippeout | bye |
| 16:01.29 | *** join/#htc-linux doodles_ (n=chatzill@BACARDI.MIT.EDU) |
| 16:02.58 | *** part/#htc-linux doodles_ (n=chatzill@BACARDI.MIT.EDU) |
| 16:03.40 | *** join/#htc-linux power_usr (n=chatzill@BACARDI.MIT.EDU) |
| 16:05.40 | *** join/#htc-linux dzo (n=dzo@121-98-128-127.bitstream.orcon.net.nz) |
| 16:06.26 | *** join/#htc-linux xray7224 (n=xray7224@89-168-153-197.dynamic.dsl.as9105.com) |
| 16:06.36 | xray7224 | hey |
| 16:07.40 | xray7224 | i have a htc elf and i want to run linux but im not sure if it works ont he elf |
| 16:08.13 | Dunedan | yeah |
| 16:08.16 | Dunedan | Debian ist booting. |
| 16:08.41 | xray7224 | debian works, hmmm not keen on debian but i suppose its that or wm |
| 16:09.00 | Dunedan | xray7224: erm sorry. I'm talking about blackstone. |
| 16:09.20 | xray7224 | ah right |
| 16:09.26 | xray7224 | no worries |
| 16:09.40 | xray7224 | i want android but i dont think i have a hope in hell with getting that working |
| 16:10.59 | xray7224 | no |
| 16:11.26 | power_usr | Hey, looking at chat logs, two days ago Maejrep posted two links to zImage for RAPH800. Did either of these turn out OK? |
| 16:37.08 | *** join/#htc-linux MethoS- (n=lem@dyndsl-085-016-166-034.ewe-ip-backbone.de) |
| 16:54.25 | *** join/#htc-linux MethoS-- (n=lem@dyndsl-085-016-166-021.ewe-ip-backbone.de) |
| 17:00.50 | Dunedan | hm, I couldn't get a login prompt with debian :-( |
| 17:14.55 | *** join/#htc-linux MethoS- (n=lem@host-091-096-211-235.ewe-ip-backbone.de) |
| 17:32.04 | dcordes | Dunedan: at least you booted. you could check /etc/inittab compare it to the angstrom one |
| 17:32.44 | Dunedan | dcordes: Got it in the meantime. /dev/tty1 was missing ... |
| 17:33.29 | *** join/#htc-linux BHSPitLappy (n=BHSPitLa@unaffiliated/bhspitmonkey) |
| 17:38.06 | dcordes | Dunedan: so you created the node manually? can you make a textfile with all the steps? |
| 17:38.19 | Dunedan | dcordes: yeah. I'm doing some documentation. |
| 17:50.15 | Dunedan | usbnet is working (well no surprise) |
| 17:56.21 | *** join/#htc-linux techie (n=blarg@74.235.162.90) |
| 17:56.22 | *** join/#htc-linux t3chi3 (n=blarg@74.235.162.90) |
| 18:05.22 | Dunedan | ok, further research has to wait till later this evening. But Debian on such a device is just awesome. |
| 18:16.02 | *** join/#htc-linux mooky (n=suzannet@berger.projecthugo.co.uk) |
| 18:20.24 | *** join/#htc-linux Pure4Real (n=pure4rea@89-97-140-219.ip17.fastwebnet.it) |
| 18:25.43 | *** join/#htc-linux opennandra (n=opennand@afrodita.advanet.sk) |
| 18:25.49 | *** join/#htc-linux BHSPitLappy (n=BHSPitLa@unaffiliated/bhspitmonkey) |
| 19:01.47 | *** join/#htc-linux Pure4Real_ (n=pure4rea@89-97-140-219.ip17.fastwebnet.it) |
| 19:14.51 | *** join/#htc-linux ali1234 (n=al@robotfuzz.co.uk) |
| 19:15.08 | *** join/#htc-linux AstainHasPS3 (n=AstainHe@unaffiliated/astainhellbring) [NETSPLIT VICTIM] |
| 19:15.08 | *** join/#htc-linux PoohbaLT (n=BlkPoohb@c-69-141-71-249.hsd1.nj.comcast.net) [NETSPLIT VICTIM] |
| 19:15.09 | *** join/#htc-linux Kevin2 (n=Kevin2@207-237-194-161.c3-0.avec-ubr2.nyr-avec.ny.cable.rcn.com) [NETSPLIT VICTIM] |
| 19:15.09 | *** join/#htc-linux einand (n=einand@unaffiliated/einand) [NETSPLIT VICTIM] |
| 19:15.09 | *** join/#htc-linux ecze (n=ecze@eczema.ecze.com) [NETSPLIT VICTIM] |
| 19:15.09 | *** join/#htc-linux defiant (n=add@p0pc0rn.eu) [NETSPLIT VICTIM] |
| 19:27.10 | mordy_ | haha, i finally got angstrom to work |
| 19:27.15 | mordy_ | hmm.. no wifi in this thing? |
| 19:35.08 | mordy_ | wow, this acx driver is buggy :/ |
| 19:40.28 | mordy_ | hey, what's the escape key on the universal? i'm stuck in vi :( |
| 19:47.29 | *** join/#htc-linux pleemans (n=toi@d54C2AAB7.access.telenet.be) |
| 19:48.04 | *** join/#htc-linux Shinto (n=John@f048178180.adsl.alicedsl.de) |
| 19:53.53 | power_usr | Hey what is angstrom? |
| 19:56.10 | mordy_ | it's jsut another distro |
| 19:57.50 | mordy_ | i just wish it had sshd, although it does use a considerable amount of ram |
| 20:21.10 | *** join/#htc-linux swc|666 (n=carramro@unaffiliated/swc666/x-4934821) |
| 20:28.49 | *** join/#htc-linux wippeout (n=zsirc@unaffiliated/wippeout) |
| 20:29.03 | wippeout | hello |
| 20:31.06 | *** join/#htc-linux Untouchab1e (n=Untoucha@77.17.46.196.tmi.telenormobil.no) |
| 20:31.45 | Untouchab1e | good evening! anyone has a adp1 here? :) |
| 20:32.07 | Untouchab1e | anyone? |
| 20:34.43 | wippeout | can we later get the htc magic nbh rom and put it in the blackstone ? |
| 20:35.03 | wippeout | the both devices are very similar |
| 20:57.33 | dcordes | wippeout: hi again. magic? |
| 20:57.44 | wippeout | yes |
| 20:57.44 | dcordes | BabelO: ping |
| 20:57.52 | wippeout | the htc g2 |
| 20:58.06 | dcordes | ok |
| 20:58.32 | dcordes | some people talked about the dream radio rom on other htcs lately |
| 20:58.47 | dcordes | but why would you want to do that? |
| 20:59.20 | wippeout | for android |
| 20:59.26 | wippeout | full support |
| 21:00.08 | ali1234 | well |
| 21:00.15 | ali1234 | do they have the same radio core? |
| 21:00.19 | wippeout | to have natively and fully supported android on my htc blackstone |
| 21:00.30 | dcordes | wippeout: I guess you can just try ;) |
| 21:00.31 | wippeout | i dont know |
| 21:00.49 | dcordes | ali1234: yeah |
| 21:00.50 | ali1234 | do they have the same cpu? |
| 21:01.23 | wippeout | take screenshots of htc blackstone and htc g2 |
| 21:01.36 | ali1234 | if they have the same cpu then there is a very very good chance that the radio rom will work on different phones... in fact there is a very good chance they all use the same rom anyway |
| 21:01.44 | wippeout | ali:i suppose |
| 21:01.56 | dcordes | ali1234: they don't. the wince radios are different |
| 21:02.22 | ali1234 | how is it different? |
| 21:02.28 | wippeout | htc g2 doesnt have wince |
| 21:02.41 | wippeout | it s a pure android phone |
| 21:02.58 | ali1234 | we know for example, that omap smartphones, no matter what OS they use, all use the same radio roms |
| 21:03.34 | wippeout | i hope that |
| 21:03.42 | dcordes | ali1234: e.g. wince radio rom has a ppp serial device and radio rom on dream uses "rmnet" |
| 21:03.58 | dcordes | for data |
| 21:04.17 | wippeout | MAGIC.nbh ->BLACIMG.nbh |
| 21:04.33 | dcordes | wippeout: it's possible |
| 21:04.38 | ali1234 | the omap radio rom has both serial ppp and packet level interfaces... it is software selectable |
| 21:04.42 | dcordes | wippeout: you might ask dream_kill about it ;) |
| 21:05.09 | wippeout | ok |
| 21:05.20 | dcordes | ali1234: for the msm7* it's burnt into the amss. nothing selectable |
| 21:05.54 | dcordes | wippeout: which X image did you try? did it work well? |
| 21:06.03 | ali1234 | has nobody tried to analyse the images then? |
| 21:06.15 | wippeout | no i just hope and wait |
| 21:06.30 | ali1234 | msm7* includes a very different cpus |
| 21:07.16 | wippeout | om |
| 21:07.57 | wippeout | what are mainly features to have linux on htc ? |
| 21:08.01 | dcordes | ali1234: msm7?0?? :) |
| 21:08.08 | wippeout | advantages |
| 21:08.37 | wippeout | i dont talk about android |
| 21:09.42 | ali1234 | there is more difference between msm7500 and msm7500a than there is between omap710/730/750 |
| 21:10.15 | ali1234 | *850 |
| 21:10.33 | mordy_ | dcordes: oh, finally got the angstrom rootfs to run as an initrd |
| 21:11.29 | mordy_ | sucks that it doesn't have sshd thoguh... although i guess i can try and use it anyway |
| 21:12.10 | mordy_ | and the wifi is broken pretty much :/ |
| 21:13.14 | wippeout | dcordes : initrd vs rootfs ? |
| 21:14.52 | mordy_ | wippeout: well, the images that are available are intended to be used as root filesystem on an actual media |
| 21:15.43 | wippeout | i tested initrd and rootfs way |
| 21:15.57 | wippeout | a .bin file for initrd |
| 21:16.16 | wippeout | angstrom.bin for initrd |
| 21:16.20 | mordy_ | the one i used was a tarball |
| 21:17.40 | *** join/#htc-linux m0zzie (n=m0zzie@203-206-130-101.perm.iinet.net.au) |
| 21:21.30 | wippeout | bye |
| 21:22.00 | Dunedan | Does somebofy know if I can give linux on an Blackstone safely more RAM, than the 76MB which are configured in the most default.txts? |
| 21:25.09 | *** join/#htc-linux Untouchab1e (n=Untoucha@82.147.51.146) |
| 21:25.15 | Untouchab1e | hi! Anyone here got an ADP1? |
| 21:30.05 | dcordes | mordy_: as long as you have wireless tools wifi should be no problem. all angstrom rootfs have dropbear instead of sshd |
| 21:30.26 | dcordes | Dunedan: try |
| 21:30.37 | dcordes | Dunedan: you won't break anything |
| 21:30.40 | mordy_ | dcordes: and how do i use dropbear? |
| 21:30.47 | Dunedan | ok, that's what I wanted to hear ;-) |
| 21:31.42 | dcordes | mordy_: same way as you use openssh-server |
| 21:33.59 | mordy_ | gah, now i can't even ping it :/ |
| 21:35.58 | mordy_ | hehe this is cool |
| 21:36.49 | mordy_ | it won't pick anything up in the scan :/ |
| 21:37.31 | dcordes | you provide the driver with a firmware? |
| 21:37.54 | mordy_ | i'm just using the amstrong image.. let me check in /lib/firmware |
| 21:38.04 | mordy_ | although i should be getting an error about missing firmware |
| 21:38.53 | mordy_ | http://pastebin.com/f76d2307b |
| 21:38.53 | dcordes | maybe it's the wrong firmware file. get a known working one |
| 21:39.22 | dcordes | acx: === chipset TNETW1100B, radio type 0x0D (Maxim), form factor 0x03 (Compact Flash), EEPROM version 0x05: uploaded firmware 'Rev 1.10.7.K' === |
| 21:40.05 | mordy_ | and what's the latest? |
| 21:40.09 | dcordes | http://linuxtogo.org/~htcpxa/htcuniversal/index.html these images should have the correct formware |
| 21:40.30 | mordy_ | i'm quite sure that's where i have this one from |
| 21:41.09 | dcordes | ok |
| 21:41.28 | mordy_ | let me verify thouugh.. |
| 21:42.51 | mordy_ | i stripped out Qtopia from this image, fi that matters |
| 21:43.41 | *** join/#htc-linux techie (n=blarg@74.235.162.90) |
| 21:44.01 | mordy_ | yeah, the firmware is from thaqt site. same md5 |
| 21:44.06 | *** join/#htc-linux blargg (n=blarg@74.235.162.90) |
| 21:44.55 | *** join/#htc-linux wdslbr (n=asa@dslb-088-069-211-174.pools.arcor-ip.net) |
| 21:51.52 | mordy_ | hmm.. any suggestions? |
| 21:51.54 | *** join/#htc-linux wdslbr (n=asa@dslb-088-069-211-174.pools.arcor-ip.net) |
| 21:53.32 | *** join/#htc-linux MethoS-- (n=lem@dyndsl-085-016-165-219.ewe-ip-backbone.de) |
| 21:54.42 | Dunedan | dcordes: Could you please tell me how to determinate the maximal ramsize to use? |
| 21:55.40 | Dunedan | If I set a highter mem as kernel param, it won't boot linux anymore. |
| 21:58.53 | mordy_ | http://pastebin.com/m6ff26a32 |
| 21:59.13 | mordy_ | that's all i'm using now -- lsmod -- it's still horribly buggy though :( |
| 22:12.14 | mordy_ | gah, stupid windows |
| 22:12.28 | mordy_ | how do i set up a usb network connection in windows? or can i only od it in linux |
| 22:16.09 | maejrep | you need a cdc-ether driver |
| 22:16.27 | mordy_ | hmm... how do i get it on windows though? |
| 22:16.46 | maejrep | no clue |
| 22:16.52 | mordy_ | lol |
| 22:17.12 | maejrep | google? i run linux, so couldn't say |
| 22:17.46 | *** join/#htc-linux cr2 (n=cr2@ip-77-25-112-138.web.vodafone.de) |
| 22:17.49 | mordy_ | me too |
| 22:18.47 | mordy_ | i meant windows mobile though. i know it's somewhat possible using a windows usb host.. |
| 22:18.51 | mordy_ | whatever |
| 22:21.59 | cr2 | mordy_: we don't have msm-A usb host driver. yet |
| 22:22.17 | dcordes | cr2: he has uni |
| 22:22.47 | mordy_ | hehe, it works with linux, just not windows - it's ok.. i can use wifi for file transfer |
| 22:22.48 | cr2 | on the uni we don't know if it's properly soldered |
| 22:23.16 | mordy_ | i need to transfer files via wifi and http lol |
| 22:24.47 | cr2 | wifi on the uni more or less works |
| 22:24.47 | mordy_ | not for me |
| 22:25.24 | cr2 | maejrep: got some new patches ? :) |
| 22:25.42 | maejrep | cr2: was thinking about committing the clock api changes |
| 22:25.45 | mordy_ | where would i build it though :P |
| 22:25.51 | cr2 | maejrep: i feel completely demotivated to reinvent the wheel myself |
| 22:25.51 | mordy_ | i don't have any ARM platform |
| 22:25.59 | maejrep | lol, which wheel? |
| 22:26.17 | cr2 | maejrep: what you have already done :) |
| 22:26.30 | cr2 | mordy_: ? crosscompile ? |
| 22:26.39 | mordy_ | bah, i'm noobish sorta |
| 22:26.53 | mordy_ | i have enough trouble compiling stuff against external kernels |
| 22:27.01 | mordy_ | never mind external arches |
| 22:27.08 | cr2 | maejrep: there was some much developemnt already, like the accelerometer driver. |
| 22:27.16 | maejrep | oh really? |
| 22:27.19 | maejrep | who did that |
| 22:28.00 | cr2 | mordy_: it's no more difficult than installing a crosscompiler toolchanin, and prepend the env variables to make |
| 22:28.18 | cr2 | maejrep: forgot already. probably j0b0 |
| 22:28.43 | cr2 | i must have it locally somewhere. |
| 22:32.04 | maejrep | grr, who broke git :p |
| 22:33.36 | maejrep | raph doesn't compile with blackstone support enabled |
| 22:34.04 | cr2 | blackstone patch is such a hack that really hirts an eye ;) |
| 22:34.17 | cr2 | s/hi/hu/ |
| 22:36.46 | *** join/#htc-linux MaRciN_PL (n=IceChat7@chello089077138234.chello.pl) |
| 22:39.54 | cr2 | board-htcblackstone-panel.c cut'n'pastes a lot of code that is completely irrelevant, like the toshiba registers and setup |
| 22:40.21 | cr2 | and the pasted raph800 settings are probably wrong too |
| 22:41.41 | power_usr | I'm ready to test a RAPH800 build whenever it gets uploaded :) |
| 22:42.43 | maejrep | cr2: Created commit 55740d7: Update MSM Clock API, fix RAPH800 colors |
| 22:42.50 | mordy_ | hrmmm.. the x11 root fs won't work nicely as an initrd |
| 22:42.55 | mordy_ | but the qtopia one does |
| 22:42.57 | cr2 | i still don't undertsand one thing |
| 22:43.03 | cr2 | <PROTECTED> |
| 22:43.04 | cr2 | <PROTECTED> |
| 22:43.06 | cr2 | <PROTECTED> |
| 22:43.17 | maejrep | it works fine for me without that btw |
| 22:43.36 | cr2 | why can't we declare the usb eth and "network" class |
| 22:44.10 | cr2 | something is broken here too: |
| 22:44.13 | cr2 | printk(KERN_ERR "mdp irq already on already on %x %x\n", |
| 22:44.15 | cr2 | <PROTECTED> |
| 22:44.50 | maejrep | o.0 |
| 22:44.58 | cr2 | and don't get me on the msm_ts.c ;) |
| 22:45.04 | *** join/#htc-linux captnoord (i=5147a47b@gateway/web/ajax/mibbit.com/x-a965a12332219aca) |
| 22:45.44 | cr2 | maejrep: i suggest to name all the gpios, and put them into a header. |
| 22:46.02 | maejrep | i agree, but a different header for each raph100/800 type? |
| 22:46.12 | maejrep | also it still needs to be determined at runtime |
| 22:46.18 | maejrep | so that makes it difficult to put into a header |
| 22:46.56 | maejrep | you can't define pdata structs with ternary operators |
| 22:47.25 | *** join/#htc-linux zycho (n=zycho@a89-183-82-24.net-htp.de) |
| 22:47.28 | cr2 | looking at the patch :) |
| 22:47.42 | cr2 | maejrep: but the hardcoded numbers are really evil... |
| 22:48.03 | AstainHasPS3 | hows it going maejrep |
| 22:48.20 | cr2 | and lead a lot of other people to make dumb assumptions |
| 22:48.43 | cr2 | AstainHasPS3: new ptch is in git |
| 22:48.57 | AstainHasPS3 | cool |
| 22:49.21 | cr2 | maejrep: .clk_id = USB_HS_CLK, .idx = 25, .offset = 0x2c0, |
| 22:49.51 | cr2 | maejrep: i think that the 0x0 , 0x100+ and +0x200 areas have different purpose |
| 22:50.19 | maejrep | ie, not clocks? |
| 22:50.25 | cr2 | at least they are separated (as functions) in oemsbl |
| 22:50.40 | cr2 | well, let's leave it as is for now. |
| 22:50.51 | maejrep | yeah, been using it for a long time now, and doesn't seem broken |
| 22:50.57 | cr2 | if we will get more information, we may modify it- |
| 22:51.02 | maejrep | we can make it more "correct" later |
| 22:51.03 | *** join/#htc-linux toer (i=tore@179.81-166-86.customer.lyse.net) |
| 22:51.10 | cr2 | agreed |
| 22:53.47 | cr2 | maejrep: static unsigned long pc_clk_get_rate(uint32_t id) |
| 22:53.55 | cr2 | why is it only for the SD ? |
| 22:54.22 | maejrep | not sure, I think we just never knew for sure hwo to get it for the other clocks |
| 22:54.23 | cr2 | btw, i think that reading the MD/NS register does not provide the right data anyway |
| 22:54.41 | cr2 | wince reads the values, only to orr or bic specific bits |
| 22:54.46 | maejrep | all I changed there was whitespace |
| 22:54.49 | maejrep | (turning spaces into tabs) |
| 22:54.59 | cr2 | but you can't derive anything useful from the read value itself. |
| 22:55.34 | cr2 | + //TODO: support all clocks |
| 22:55.35 | cr2 | + printk("unknown clock: %u\n", id); |
| 22:55.48 | maejrep | bbiaf |
| 22:55.51 | cr2 | hardcode the name ? |
| 22:59.18 | AstainHasPS3 | cr2 the new checkin having the smd tty code that for gsm stuffs too? |
| 22:59.38 | *** join/#htc-linux dzo (n=dzo@121-98-128-127.bitstream.orcon.net.nz) |
| 23:00.18 | *** join/#htc-linux Student (n=Student@62.16.118.7) |
| 23:02.05 | cr2 | AstainHasPS3: does not look so. |
| 23:02.34 | power_usr | cr2: What are the key features being checked in since the latest release? th |
| 23:02.35 | power_usr | thx |
| 23:02.35 | cr2 | it hardcodes smd1, from what i can see |
| 23:02.54 | cr2 | power_usr: what is 'release' ? |
| 23:03.14 | power_usr | 20090219 is the latest posted on Connect-UTB |
| 23:03.16 | power_usr | I guess that one |
| 23:04.03 | cr2 | the epson devices switched to 565 mode |
| 23:04.13 | cr2 | to get right colors |
| 23:04.33 | cr2 | i guess wince also uses 666 on the raph100 |
| 23:04.47 | cr2 | otherwises we would have got a lot of troubles before. |
| 23:04.53 | power_usr | OK |
| 23:05.05 | cr2 | wastes a bit of fbram though. |
| 23:05.27 | cr2 | i doubt that somebody can see the difference between 565 and 666 |
| 23:05.36 | cr2 | on a small 2.8" lcd anyway |
| 23:05.52 | power_usr | This is RGB you are talking about, and bits? |
| 23:06.02 | cr2 | yes |
| 23:06.04 | power_usr | OK |
| 23:06.12 | *** join/#htc-linux captnoord (i=5147a47b@gateway/web/ajax/mibbit.com/x-794b2e0959543549) |
| 23:06.47 | *** join/#htc-linux imfloflo (n=imfloflo@cap31-6-88-180-73-121.fbx.proxad.net) |
| 23:07.03 | cr2 | it would be nice to switch raph100 into 565 mode, though. |
| 23:07.28 | AstainHasPS3 | tried that one 100 didn't like it |
| 23:07.33 | AstainHasPS3 | had screwed up colors |
| 23:07.52 | cr2 | AstainHasPS3: you have changed only the dma flags |
| 23:08.15 | AstainHasPS3 | oh? |
| 23:08.20 | cr2 | AstainHasPS3: but not the lcd spi init/ toshiba init |
| 23:08.26 | AstainHasPS3 | ahh ic |
| 23:08.40 | cr2 | but if wince uses 666, then we will never know how to switch to 565 |
| 23:08.49 | cr2 | but we need to investigate it. |
| 23:09.14 | AstainHasPS3 | what difference does it make 666 vs 565 or 655? |
| 23:09.33 | cr2 | a lot |
| 23:09.58 | cr2 | you need 32bit vs 16bit to store the rgba quad |
| 23:10.05 | AstainHasPS3 | ahh ok |
| 23:10.16 | cr2 | and the internal conversions look different |
| 23:10.26 | cr2 | but it's hidden from a normal user |
| 23:10.42 | cr2 | unless somebody implicitely assumes 16bit color |
| 23:11.03 | cr2 | i thought m$ requires the vendors to do 565 |
| 23:11.22 | cr2 | but raph100 obviously works in 666 mode. |
| 23:20.05 | power_usr | cr2: so the RGB thing is the key addition since 20090219 release? |
| 23:20.36 | cr2 | i think yes. and the phone support for cdma |
| 23:20.50 | power_usr | CDMA phone support is huge! |
| 23:20.58 | power_usr | But I guess no microphone |
| 23:21.00 | cr2 | but i guess maejrep has broken gsm now ;) |
| 23:21.09 | cr2 | no, sound is not yet there. |
| 23:21.18 | AstainHasPS3 | wait huh he broke gsm? |
| 23:21.20 | power_usr | OK, but still, wow that's great. |
| 23:21.25 | cr2 | and gps does not work too. |
| 23:21.40 | power_usr | A very promising step for RAPH800 owners |
| 23:21.48 | cr2 | AstainHasPS3: the UMTS data channel should be smd7 |
| 23:21.56 | cr2 | power_usr: sure |
| 23:22.24 | cr2 | AstainHasPS3: and afaik there is no gps on a cdma smd27 |
| 23:22.43 | AstainHasPS3 | hmm cr2 how would we find out what smd it is on? |
| 23:22.46 | cr2 | so it's a bit unflexibale now. |
| 23:23.21 | cr2 | AstainHasPS3: for cdma ? it's not known. the gps data is not found in the smem |
| 23:23.39 | AstainHasPS3 | anything I can do with haret? |
| 23:23.58 | cr2 | i'm not excited about msm gps performance anyway. |
| 23:24.08 | *** join/#htc-linux _ecze (n=ecze@eczema.ecze.com) |
| 23:24.13 | cr2 | i think no. we need to find a way to trace rpc in wince. |
| 23:24.35 | maejrep | cr2: broke gsm? |
| 23:24.36 | maejrep | how? |
| 23:24.37 | cr2 | asking dzo may help :) |
| 23:24.53 | cr2 | maejrep: you have hardcoded smd1 as a data channel now ? |
| 23:25.55 | cr2 | then if(raph800) smd1 else smd7 may be better. for now. |
| 23:26.32 | maejrep | no |
| 23:26.38 | cr2 | 800|500 |
| 23:26.40 | cr2 | ? |
| 23:26.40 | maejrep | well |
| 23:27.00 | maejrep | I added smd1 to be usable as a tty, but that didn't break gsm, cause gsm wasn't registering smd7 either |
| 23:27.13 | cr2 | ok |
| 23:27.29 | cr2 | but an "if" will be better. |
| 23:27.56 | maejrep | true, actually we could probably make it a boot param |
| 23:27.58 | cr2 | maejrep: can you add smd7 for non800/500 ? |
| 23:28.29 | cr2 | the gsm channels can be all derived from smem |
| 23:28.44 | cr2 | the hack is cdma only ? |
| 23:30.40 | maejrep | the hack is only for smd_7500 for detecting the channels |
| 23:30.48 | maejrep | but smd_tty.c checks the cid before allowing it |
| 23:31.03 | maejrep | http://git.linuxtogo.org/?p=groups/mobile-linux/kernel.git;a=commit;h=57f8b6c754c93c4614377fd281baef68bc1ea215 |
| 23:31.10 | cr2 | ok. but the smd1 vs smd7 ? |
| 23:31.20 | maejrep | what about it? |
| 23:31.34 | maejrep | smd7 would have never worked previously, without changing smd_tty.c |
| 23:31.46 | maejrep | that might have been what NetRipper was doing to test it |
| 23:31.52 | AstainHasPS3 | maejrep does it work now? |
| 23:31.59 | maejrep | does what work? |
| 23:32.10 | AstainHasPS3 | smd1 is data right? |
| 23:32.12 | mordy_ | hey, are the images here ok? http://www.linuxtogo.org/~htcpxa/htcuniversal/images/x11-GPE/ <-- i'm trying to make the OpenMoko image into an initrd, and i'm getting a 'filename too long' - bad archive? |
| 23:32.24 | cr2 | maejrep: uh, you get the dzo award :) |
| 23:32.24 | maejrep | AstainHasPS3: yes, for cdma, but I havent tested it yet |
| 23:32.25 | NetRipper | oops, did i not commit that |
| 23:32.27 | maejrep | this just allows the smd to work |
| 23:32.29 | mordy_ | for cpio |
| 23:32.34 | maejrep | cr2: lol what? |
| 23:33.03 | AstainHasPS3 | maejrep what would one need to do to test it? |
| 23:33.12 | cr2 | maejrep: an award for reckless hardcoding the numbers into the kernel :) |
| 23:33.47 | maejrep | google did it first :p |
| 23:34.49 | maejrep | AstainHasPS3: follow the vogue initrd for setting up the modem |
| 23:34.54 | cr2 | AstainHasPS3: you can actually try ppp with the latest git |
| 23:35.10 | maejrep | they write HTC_DUN=0 and ATDT#777 to the modem, then start up pppd on smd1 |
| 23:35.49 | cr2 | maejrep: it's ev(do) something |
| 23:36.12 | dcordes | what does HTC_DUN=0 do? |
| 23:36.28 | cr2 | maejrep: for gprs/umts you need at+cgdcont and some other (standard) things |
| 23:36.28 | maejrep | dunno, but its in the vogue initrd |
| 23:36.40 | cr2 | dcordes: something htc specific |
| 23:36.50 | dcordes | cr2: on kais it's not needed for ppp |
| 23:37.10 | cr2 | dcordes: kais != cdma |
| 23:38.18 | cr2 | dcordes: can we add the umts cfg to the angstrom initrd ? |
| 23:38.24 | maejrep | dcordes: vogue initrd checks phone type at boot. if gsm, it changes the setupmodem scripts |
| 23:38.31 | dcordes | cr2: which one? |
| 23:38.35 | cr2 | enetering the pppd paramteres by hand can be panful |
| 23:39.21 | dcordes | ok I will look up the parameters in the vogue initrd and add them to angstrom |
| 23:39.25 | cr2 | dcordes: i use 'pon' on nc10, but it's debian-specific afaik |
| 23:39.59 | dcordes | maejrep: blackstone breakage is fixed with your comitt? |
| 23:40.46 | maejrep | $ cat initmodem1;echo |
| 23:40.46 | maejrep | AT+HTC_DUN=0 |
| 23:40.47 | maejrep | $ cat initmodem2;echo |
| 23:40.48 | maejrep | ATDT#777 |
| 23:40.57 | maejrep | $ cat initmodem2-gsm ;echo |
| 23:40.57 | maejrep | ATD*99***1# |
| 23:41.08 | maejrep | dcordes: no, I only changed the mdp.c part |
| 23:41.14 | maejrep | I didn't fix board-blackstone |
| 23:41.37 | maejrep | the compile error happens if you select all 5 machines (raph/diam, cdma/gsm, +blackstone) |
| 23:41.41 | dcordes | how does board-blackstone destroy raph build? |
| 23:41.47 | dcordes | ah |
| 23:41.53 | maejrep | cause it redefines an already existing function |
| 23:42.08 | maejrep | if you don't mix them, it compiles |
| 23:42.39 | dcordes | don |
| 23:42.43 | dcordes | don't see the problem then |
| 23:43.08 | maejrep | because we're trying to make it possible to build one kernel that will boot all the machine types, within reason |
| 23:43.19 | dcordes | ok |
| 23:43.25 | maejrep | like on raph/diam, you can compile all 4 machine types, and the zImage should boot on all 4 |
| 23:43.32 | dcordes | yea |
| 23:44.35 | maejrep | even my smd_7500 can be compiled in and will still boot on a raph100, which doesn't need it |
| 23:45.14 | dcordes | no doubt it's useful |
| 23:45.23 | maejrep | it's not critical :p |
| 23:45.25 | dcordes | I didn't make blackstone patch |
| 23:46.39 | maejrep | cr2: another way we can fix the color issue is to get the epson controller setup with 666/18bpp |
| 23:47.00 | maejrep | but i'm sure it requires a lot more parameters to be changed than the one that I tried |
| 23:47.17 | cr2 | maejrep: the blac100 patch does a lot of #ifdef |
| 23:47.46 | maejrep | yeah ;x |
| 23:47.50 | cr2 | maejrep: 565 for raph100 may bemore useful |
| 23:47.50 | dcordes | maejrep: it's also useful for openembedded because it doesn't need to decide cdma vs gsm |
| 23:48.40 | cr2 | why do they hardcode the screen size into msm_ts.c ??? |
| 23:48.52 | *** join/#htc-linux miknix (n=miknix@gentoo/developer/miknix) |
| 23:48.59 | cr2 | is android incapable of screen calibration ?? |
| 23:49.17 | maejrep | might be because the epson controller doesn't respond with capabilities |
| 23:49.51 | AstainHasPS3 | doesn't g1 have screen calibration stuffs? |
| 23:50.21 | cr2 | i also do not understand why do they have problems with pin |
| 23:50.23 | maejrep | would be nice if it does, so we don't have to use the msmts_calib param |
| 23:50.38 | cr2 | we had this problem for qtopia, because it was not implemented. |
| 23:52.21 | *** join/#htc-linux [1]BabelO (n=BabelO@lun34-2-82-238-28-28.fbx.proxad.net) |
| 23:52.48 | dcordes | hi [1]BabelO |
| 23:53.19 | cr2 | [1]BabelO: what was the qtopia pin problem ? |
| 23:54.13 | *** join/#htc-linux [2]BabelO (n=BabelO@lun34-2-82-238-28-28.fbx.proxad.net) |
| 23:54.35 | maejrep | lol |
